Tips for sewing with linen jersey, a new Lamazi post

Did you know that linen jersey was even a thing? It’s an unusual fabric which you don’t see often, we all know knits are available in most other fibre types-cotton, wool, silk or man-mades for example- but I’ve never worked with it before so when Liana invited me to sew my next Lamazi project using it, and to pass on any hints and tips for sewing it, I was up for the challenge. 

This 100% linen jersey comes from Mind the Maker in a range of colours and I picked the Dry Mustard shade which is a lovely vibrant ochre. The fabric has a beautiful lustrous sheen on the right side, the reverse is duller so it makes it much easier to tell the difference between the two. It has lovely light drapey quality too and is slightly sheer.

Linen fabric is not a textile known for its inherent stretch qualities and this jersey does feel slightly different from other knits because it has only a small amount of stretch along its length and quite a lot of stretch across the width but it has very little recovery so once it’s been stretched out it will stay like that at least until it’s washed again. During construction the application of plenty of steam will encourage some of this accidental stretching to be eased back into position so, coupled with its sheerness, this means that you need to think carefully about what garment to sew with it. 

Plenty of steam will help remove most unwanted bagginess like this

The properties of linen fabric itself [cool in warm weather, warm in cold weather] mean that it would be ideal for loose-fitting leisure or exercise wear, for yoga or Pilates for example. I would definitely say it’s better to avoid anything that is particularly close fitting because areas like the elbows or wrists would become stretched or baggy with little recovery. However the fabric has a lovely drape and its fine gauge allows it to be gathered up successfully so these properties could be exploited instead.

Bearing all these factors in mind I decided to make (another) Sewing Revival Heron dress which I would hack into a blouse. The pattern has a neckline which is gathered using elastic along with raglan sleeves with deep elasticated cuffs. To mix it up further I decided to pull the hemline in onto elastic rather than have a wide smock silhouette.

First things first, I washed the fabric by hand to remove any risk of excessive shrinkage or twisting in the machine. If you want to wash it in the machine then it might be an idea to overlock the cut ends together first to form a long loop and place it into a large washing bag to protect it further. Alternatively you could press it on your ironing board with plenty of steam instead. If at all possible it is better to dry the fabric flat, and certainly don’t wring or twist it. All of this might sound off-putting, and it is clearly not as straightforward as chucking a nice stable cotton into the machine but this is a luxurious fabric and deserves to be treated and handled carefully in the preparation. When it comes to cutting out your pattern pieces lay the fabric as flat as possible, handle it gently and don’t pull it about too much, especially if you decide to fold it. I made a whole back pattern piece for my top so that I could cut it flat, another appeal of the Heron pattern for me is that it has just three pieces so it’s a relatively quick sew usually. 

After cutting all the pieces the first thing I did was stabilise all the raglan shoulder seams using some iron-on seam tape, I did this to prevent any unwanted stretching before I sewed the sleeves in later on. I added small squares of iron-on interfacing to reinforce the bottom of the opening on the centre front seam too. I also decided to press all the folded parts of the casings/ruffles for the neckline, sleeves and hem before sewing anything together, just so that I was handling the cut-out pieces as little as possible, again to prevent unwanted stretching before they got joined together. I also tacked these folded parts into position temporarily. All this might sound excessive but I wasn’t in a rush, and I found the slow and considered processes very soothing at quite a difficult time. 

iron-on stay tape to prevent unwanted stretching of the raglan seams
I pressed and tacked casing/ruffles before joining the sections together later on
reinforcing the bottom of the neck opening with small squares of iron-on interfacing.

Something else I did before commencing was check on fabric scraps which needle and stitch-type would give me the best results. A ballpoint needle suitable for stretch/knits/jersey is essential to prevent snagging which could lead to laddering of this delicate fabric, and I found a short straight stitch was better than a narrow zigzag but you must do what works best on your own machine. You could sew a garment together entirely on an overlocker but be aware of the lack of rebound this fabric has so if it gets stretched or misshapen while it’s being sewn then it’s probably like that permanently. I also tested the overlocker finish before diving in for the same reasons. If you don’t have an overlocker this fabric is fine enough that where possible you could probably sew self-neatening French seams, or a wide zigzag might work but just be careful it doesn’t chew up the edges. If you have an overlock stitch option on your sewing machine and/or a special foot to sew an overlock-style stitch then definitely use them. Test all options before making your choice, the time taken could save you upsets later on. I slipped some folded strips of paper underneath the seam allowances when I pressed them to minimise any chance of the seam showing through on the front

testing stitches and overlocking
I popped two strips of folded paper under the centre front seam while I pressed it so that there was no show-through or unwanted shininess on the right side.

If you have a walking foot for your machine this is definitely a fabric worth using it for, even if you don’t it’s a good idea to use plenty of pins. I’m not a fan of mini-clips because I think they are too heavy and get in the way, this fabric is lightweight and I think mini-clips could distort it while you’re sewing but it’s up to you. Tacking seams is always an option too of course, any technique that prevents the fabric shifting while you sew basically.

If you’ve followed my blog for a while you’ll know I’ve made a few Herons before so the construction was straightforward, the only area I did differently was to create the ruffled hem with a wide elastic casing. I couldn’t decide between my planned 2cms or 1cm wide elastic initially so I tested with the two widths to see which I preferred-I chose to stay with the 2cms width as planned. 

testing which elastic width I preferred for the hem, this was the narrow one (the fabric scrap is wrong side out!)
and this is wider width, it’s the one I used at the hem in the end.
using a bodkin to insert the narrow elastic in the neck casing.
checking the gathered neckline on the stand
I used this quilting attachment on my machine so that I sewed an accurate parallel width for the elastic casing
close up of the elasticated hem casing

To sum up, I’m really pleased with how my first experience of sewing with linen jersey has gone, I’ll admit I was a little nervous because Liana was putting her trust in me with an expensive fabric but taking the time to plan and test, and use my existing knowledge of working with knits definitely helped. Because of the sheerness of the fabric Lamazi also provided me with a metre of Atelier Brunette crepe viscose in Ochre to make a camisole to wear underneath, I used the Simone camisole and trousers pattern by Maven which is a very quick make and a very useful garment to wear on its own or underneath other garments. The crepe viscose is a beautiful quality fabric with lovely handle and drape but be aware that there’s a disappointing amount of creasing, you might want to take that into account when planning, for example if you’re making something you’ll spend a lot of time sitting in.

all finished

As always, I hope you find my hints and tips helpful if you choose this lovely fabric, I wouldn’t recommend it to a novice sewer because some experience of sewing with other similar fabrics is definitely an advantage, plus it would be shame to end up with a costly mistake, but if you’re looking for a new challenge to add to your repertoire this could be a good start. I’ll launder the finished garment either by hand or in a wash bag on a gentle cycle in the machine. I’ll dry it flat too and store it that way, I don’t want a coat hanger to make it misshapen. If you’re a person who prefers not to worry too much about their clothes or their maintenance then this might strike you as overkill, and that’s fair enough, but I don’t think it hurts to have a few special things in our wardrobes which were worth the effort to make for ourselves. 

I’m looking forward to wearing this top as autumn is fast approaching (did summer ever arrive!?) thank you to Lamazi for providing me with the fabric to review.

Until next time, happy sewing,

Sue

A return to blogging with a Kingfisher top from The Sewing Revival

There’s been quite a lull in my sewing and blogging of late due to a distinct lack of motivation and generally feeling meh about everything. I don’t know about you but I’m utterly cheesed off with the persistence of the ‘Rona and, whilst I really try to find the positives as much as I can, there comes a time when I’m all out of good thoughts.

Anyhoo, I’ve finally managed to get my act together and to cut out and sew something which is worth blogging about!

You’ll know I use The Sewing Revival patterns a lot, and especially because they are SewOver50-friendly in their representation. Janine kindly offered me a copy of the new and improved Kingfisher top recently so here are my thoughts on it. The original version was one of the first in the Sewing Revival collection and it now features extra variations including 3 sleeve lengths and additional ruffles and frills to gussy it up.

Initially I’d settled on using a length of fabric I bought recently but in the end, whilst searching-sorry-shopping, my stash I came across a length of batik-printed lightweight cotton which had originally been a dress. I bought it as a remnant which was in two different-sized pieces pieces so I joined them right across the weft to make it useable. From that I turned it into a simple ‘pillowcase’ dress with a gathered drawstring top and hemmed at the bottom. Needless to say, this being England, I didn’t get a massive amount of wear from it because our climate is so unreliable. Sadly I don’t seem to have a photo of it now so you’ll just have to believe me.

The Kingfisher has raglan sleeves which are always so nice to make because they are simple and quick to construct. One of The Sewing Revival’s trademarks is to mix a stretch neck band, cuffs or hem with a woven fabric and this top features a ribbed, rounded neck band. But first I had to get all the pieces out of a length of fabric with a join across it at about 50cms in, plus a tear at right angles to the selvedge in another place AND a small hole just near that! I calculated that I could get a pair of 3/4 length sleeves but one would have to have the seam running horizontally across it. Another new feature of the Kingfisher is additional small ruffles to add so, instead of placing them vertically on the sleeves, I opted to cover the seam with horizontal ruffles, that way way both sleeves would look the same. After a bit of pattern Tetris I got everything I needed out including the ruffles. I started by making the sleeves.

Inside the sleeve with the exisiting join running horizontally

Because of the limitations of the fabric the ruffles were only 5cms wide so, in order to lose as little of their width as possible, I finished each edge with a rolled-hem finish on the overlocker. Check your instruction booklet because I’m sure many models will offer this feature, it will involve a few simple adjustments to the settings to achieve. A rolled hem is a quick and attractive way of neatening fine or lightweight fabrics when you can’t afford to lose too much off the edges.

Each ruffle was cut twice as long as the width of the sleeve because the fabric is quite fine and will gather up well. If you are limited for fabric (mine were cut on the straight grain) or if your fabric is quite stiff or thick, then 1.5x the width will be fine. I sewed a rolled hem on both edges of the sleeve ruffles and then ran two rows of a long gathering stitch along the centre line. Make sure the gathers are evenly distributed before sewing the ruffle down, I used a zigzag stitch to sew the ruffle in place.

I created a cuff to finish the sleeve ends by cutting two pieces of fabric from along the selvedge and sewing them on. My original plan was to create an elasticated cuff using a casing but then inspiration struck(!) and I sewed three rows of shirring instead.

Shirring works best on lighter-weight fabrics such as soft cotton-types [lawn, batiste, voile, Swiss Dot, pique, poplin if it isn’t too stiff] also most viscose/rayons, many silks, and fine woollens such as challis. This isn’t a definitive list by any means, basically nothing too thick, or stiff or overly ‘bouncy’. As with anything you’re unsure about I’d strongly suggest sewing a few samples first to see how it goes.

To begin (and these are very much my own thoughts on shirring, you will find many others which might vary to these-trial and error before you start is the best plan of action) you ideally need a bare minimum of 1.5x the eventual finished measurement but as a rule of thumb I would say at least 2 or 2.5x your finished measurement, especially if the fabric is very fine. I also wrote advice on shirring the back of a sundress in a previous blog post which you can still read here.

Gently wind shirring elastic onto your bobbin by hand, do not stretch it as you wind, you will use regular sewing thread on the top as normal. Set your stitch length as long as possible and, sewing on the right side of the work, make sure you backstitch at the start to secure your threads then sew your first row of stitching. Do not backstitch at the end of the row, carefully remove the sewing by gently pulling the elastic out so that there’s enough to tie off the ends eventually. Repeat by sewing parallel to the first row of stitch as many times as you require, I’ve just done three for the cuff. You could draw on the lines using a marker pen or chalk if it will help, I just keep the edge of the foot in line with the previous row of stitching. The work will gradually start to pucker up as you increase the rows. The photo above shows you what it looks like on the reverse.
This is the right side of the cuff, wherever possible work with the fabric flat and then joint it in a seam or to the next piece it’s connected with. It won’t be gathered up enough to start with so hover your hot iron with plenty of steam over the area and it will pucker up a lot more. When it’s gathered as much as it’s going to tie off or backstitch the threads/elastic to secure.
In the photo above, the top cuff is before the steam was applied and the lower cuff is afterwards, you should be able to see that the stitching is a fair bit tighter-looking.
Next I added small ruffles to the front raglan seams, also neatened with the rolled hem finish just on one edge. The rest of the Kingfisher was very straightforward, the ribbing band went on neatly and gives the neckline a nice finish. You could also use bias binding or make facings if you don’t want to deal with stretch but I like it like this.
Close-up of the finished neckline, I think I bought the navy ribbing from Lamazi Fabrics a little while ago.
Sleeve ruffle

I cut this top in a UK10 so it’s a closer fit than some tops I’ve generally made but I’m really happy with the fit, there’s still ample room for comfort and movement. From a fabric that was languishing in a box I’ve concocted a casual top I can wear in warmer or cooler weather.

Thank you to Janine for providing me with the pattern, I hope my review will be helpful, for a such a simple shape there are so many possibilities with it. If you haven’t tried any Sewing Revival patterns I’d definitely suggest you pop over there and take a look, and if you choose to follow any link I’ve created in this post or previous TSR ones, and you then make a purchase, I will receive a modest fee from it. You can also read my previous reviews for the Sidewinder pants, the Heron dress plus a hack, the Bellbird top and the Fantail top and it’s follow-up. If you want any more inspiration use the hashtag #KingfisherTop on Instagram or Facebook. I’ve got plans for a deep-cuff version later in the year, just so long as I don’t have another creative slump…!

Welcome back and thanks for reading this far, I’ll try not to leave it so long next time!

Until then, keep sewing!

Sue

Fantail follow-up!

I published my review of The Sewing Revival Fantail top recently and since then I’ve made a second using an alternative finish which I thought I would share with you.

the first Fantail top

This second version uses a ribbing finish on the neck, cuffs and back hem instead of hemming or elastication. I’d bought some Art Gallery viscose from Sew Me Something with an interesting graphic design and then my fellow @SewOver50er Kate @stitchmeayear generously offered me some grey ribbing, she had more than she needed. It turned out to be the perfect match and I couldn’t have planned it better if I tried.

There are separate pattern pieces for the ribbing cuffs, neck and hem and, although the same front, back and sleeve pieces are used, there are very slightly different cutting lines for the sleeve.

I had bought 1.5m of the graphic print and it has a fairly distinct one-way design which meant I needed to place each pattern piece carefully to try and get a reasonable match whilst not wasting too much fabric. I was able to do this by folding over one selvedge by just enough to position the front and back pieces along the same fold. This left a good sized piece from which I could individually position and cut a pair of sleeves whilst still just about getting a good match.

Sewing the Fantail with ribbing is very slightly different to the woven version. First, the deep ribbing band is sewn on the back in place of the narrow hem [I’m not sure if there’s a small discrepancy in the pattern or my cutting out but on both my versions I’ve found there to be about 5mm too much fabric in the back compared to the front when joining the side seams]

Like the first version I sewed the ribbing band onto the neck after joining the raglan seams and before sewing up the side seams. As I probably explained in the previous post, I always find it’s easier to put a facing, binding or whatever neck finish on whilst everything can still be laid out flat unless there’s a technical construction reason for doing it later.

The main reason for writing this second post is because I want to show you the way I turned the band at the hem-I forgot to take photos as I was making the first one! It’s a really neat way of of finishing the bottoms of the side seams and can be a useful technique in other places when you’re sewing different hems or edges together because it gives a crisp and level finish to an edge with the seams enclosed. The photos will help make more sense.

Pin the side seams together like so first, the raw edge of the deep elastic casing for the front is already pressed up by 1cm and the bottom of the ribbing is lined up against the notch for the casing.
Next, fold up the front so that it sandwiches the ribbing like this, pin in place. Now sew the seam starting at the fold on the hem. If you haven’t used this method before you may want to sew one side first and check it to make sure you’re happy with it, it can be a little confusing initially but it’s worth persevering.
Turn the hem to check it is level and, if you’re happy with it, neaten the seams however you wish. This is before I neatened the side seam but it will look like this on the inside.
The outside will look like this, so neat!

One other slight change I made was to the width of the ribbing cuffs, I cut the UK 12 pieces but they were much too baggy for my wrists so I shortened them by 5cms so they aren’t so wide and gapey.

At the moment I haven’t edge stitched any of the ribbing like I would do normally on knit garments. Because this is a combination of woven and knit fabrics I don’t want the woven fabric, at the neck especially, to end up puckered where its attached to the band so I’ve left it for now [and I don’t want holes if I had to unpick it]

The ribbing is currently not edge-stitched in case it causes puckering

I don’t normally post two of the same thing in such quick succession but I wanted to share the hem tip more than anything. I fully anticipate making a knit version of the Fantail at some point, or a short sleeve one in something really light and pretty…That’s what I enjoy about Sewing Revival patterns, so many possibilities if you have the imagination.

Until next time, Happy sewing

Sue

The Heron dress by The Sewing Revival

By being a part of the organisation of the first Sew Over 50 challenge it has meant I’ve come across pattern companies which I hadn’t heard of before. In several cases they made contact with me directly through the comments at the end of the first blog post. Not all of these companies make patterns that appeal to me personally but The Sewing Revival in New Zealand was one which did. Janine Pomeroy has created a small but growing number of simple, chic and wearable styles and because they are PDFs they are easily available to you wherever you are in the world.

Janine very generously gifted me the Heron dress (it also comes as a top too) and I’ve just finished making it up in time for my upcoming holiday.

The PDF was initially just available as A4 or US letter format but is one one of their first to also come as A0 copy shop format too. It comes with LOTS of useful and helpful information for when you print it out-there’s even instructions in how to print only the size you need if you prefer, I can’t think of another company I’ve come across which actually talks you through it, I have limited IT skills and wouldn’t have known how to do this for myself so that was helpful. Also, when ordering your pattern, you opt for the set of 3 sizes closest to the size you require according to your measurements. I like this arrangement because you don’t have an overwhelming number of lines to try and cut out from. I’m a UK 12-14 in RTW so I’ve made the size Medium and I’m very happy with it. If you do print all the sizes because you want to cut between different measurements for example then each size prints in a different colour-this is worth bearing in mind because if you print in B&W only they aren’t various styles of dot and dashed lines.

I bought some lovely pale blue viscose/linen printed with navy and red flowers from my recent visit to Ditto fabrics in Brighton specifically for the Heron. If you’re a novice sewer there is plenty of guidance included on which fabrics would work well, as well as other lay plan and cutting tips too.

It’s more pale blue than grey, you’ll see in my later photos.

There are only a few pattern pieces so it doesn’t take long to cut out and start sewing. There are some clever details which mean you don’t have lots of extra facings or elastic casings to cut and sew on, they are included which means the sewing doesn’t take that long either.

I printed out the making instructions in booklet format and I found the photos a tad small that way, I should have left them A4 for clarity although, that said, it’s fairly obvious what you’re doing and there are plenty of written instructions too.

I like the clever way the front facing is ‘grown-on’ so you just neaten the centre front seam and, eventually, once the backs and sleeves are sewn together [raglan sleeve so not tricky setting in] the neck edge gets folded over twice and stitched. This becomes the casing for the elastic.

the neck edge folds over and the stitching encloses the elastic. It’s a very simple method.

The deep cuffs fold up in a similar way which is clever because it does away with the need to neaten the cuff hem or to sew on any binding to create a casing for the elastic. It all forms one finished unit in the end.

I used the quilting guide on my machine to keep the correct distance away from the first row of stitching [it’s the piece of bent metal that might be included with your other machine attachments. It slots into a little hole just behind the foot usually and you tighten a little screw to keep it the distance you want] The elastic is wide in the sleeves which means you can’t see any of your usual visual markers and this saves having to laboriously draw on markings.

I should add that the Heron includes in-seam pockets which are a must, and there is a belt pattern too with additional ideas on how to add D-rings to it so it isn’t just a tie belt. I was so eager to finish that I didn’t notice until after I’d sewn it that the hem is finished using bias tape! This gives a lovely neat finish without losing any length, I just did a narrow rolled hem which looks fine too.

worn without the belt
…and with the belt.
rosy cheeks after a run and no make up!

As I said earlier, I was given the pattern to try out but I can honestly say I’m really pleased with my Heron and I look forward to wearing it. I’ve already got another fabric lined up for a blouse length version. I thought the sleeves looked like they might be too short but actually they are fine.

The reason The Sewing Revival came to my attention is because they use realistic models to promote their patterns, Janine made a conscious decision to do that whilst still creating covetable and wearable styles of the sort that dressmakers of any age will want. I’d love to know if you’ve used this brand and what you thought, or do you know of any others like it that could be brought to a wider audience? The Sew Over 50 challenge runs until March 15th 2019 so you’ve still got time to join in, and you don’t need to be over 50 to participate!

Until next time,

Sue