Firstly, I probably need to give you a quick explanation of why I’m making a fancy frock during the lockdown because it must seem rather incongruous.
This is my first post as a Lamazi Fabrics blogger and before the Covid-19 pandemic reared it’s ugly head I had offered to make an outfit using a slightly ‘tricky’ fabric in order to share a few hints and tips for sewing with it. I selected the beautiful Tencel/Cupro ‘Bark’ fabric in Lavender because we were going to a wedding in late May which would be the perfect chance to make a something using this special fabric. Very sadly that wedding is now postponed indefinitely but I’m making the dress because I’ll still need something to wear when it’s rescheduled.
The fabric has a lovely weight and handle which makes it drape really well. It’s has a bark-like finish and is different on each side, you could use this to your advantage if you want to create an interesting visual effect by having some pieces with one side out and some using the reverse side.
I made life harder for myself by choosing the new Bias T-shirt Dress by Trend patterns (generously gifted to me by them) in which EVERY piece except the sleeves are singles and strange shapes which means you cut everything out on a single layer of fabric right side up (RSU). Unlike most patterns, when you are cutting pairs of parts you can usually flip a piece without too much difficulty, however if you do that for a piece which must be cut RSU you would have completely reversed the print/design to the wrong side when you try to sew it up. This Tencel/Cupro has a nice look whichever side you use but my advice is to be really careful on printed fabrics before reversing any piece labelled RSU.
Next, when cutting slippery or fluid fabrics (unless you have a lovely big cutting table) you’ll need to handle them as little as possible (by which I mean pulling them about to get them into position) which might be easier said than done. I know that cutting out is most people’s least favourite part of sewing but it’s so important to take time and care at this stage. If you’re cutting out on a table with straight sides use the edges as a visual marker to get the end of your cloth at a right angle to start with, ensure the weft (across the fabric) is nice and straight as well as the warp, pull a few threads to find the grain if necessary. If you have more cloth than will fit on the table in one go you could try having the excess rolled on a cardboard tube if you have one to keep it under control rather than sliding off the table all the time.
Because my pattern has large awkward-shaped pieces cut from a single layer I had no option but to cut out on the floor! This can be physically quite tiring so you might want to get help if you need to. This is slippy slidey fabric so an extra pair of hands could help you lay it up nice and straight, again, rolling the fabric onto a long cardboard tube would also help keep the fabric taut and straight as you lay it out on the floor. This is not a fabric to use weights and a rotary cutter on unless the whole lot fits onto a cutting board without disturbing the fabric, if you’re spending time laying up the fabric carefully so that the grain lines are straight in both (warp and weft) directions you can’t then mess it about shifting a cutting mat underneath it and the pattern pieces need to be secured in place with pins. Cut out carefully moving the pieces as little as possible and try to keep them flat after cutting until you’re ready to sew. All of this will help minimise the pieces stretching out of shape, especially as a lot of this pattern has seams running on a diagonal.
Once I’ve finished cutting out it’s vital to transfer all notches and mark darts and a couple of pivot points so I use old-fashioned tailor’s tacks (obviously you can use a textile marker pen if you prefer, I often do but it’s a pale fabric and I didn’t want to risk any marks being left) It’s a habit of mine to keep all the pattern pieces attached by just a couple of pins to the fabric until I need it, so that I don’t them get muddled. These are curious-shaped pieces so the chance of having them the wrong way round could be quite high! Next I stay-stitched all the neck edges on the machine 5mm in, if you have a very loose weave fabric it would probably be sensible to stay-stitch the bottom edge of the front bodice piece to prevent stretching. If you’re using a particularly fine fabric like chiffon you should stabilise the neck, and any other seams which could stretch, by hand-stitching very narrow cotton tape or ribbon over the seam line on the wrong side of the fabric. When I worked for bridal designer David Fielden many years ago we would cut the selvedges off the silk habutai linings for the seamstresses to use on necklines.
There is just a little fraying on the cut edges which I overlocked singly as I went along, as per the pattern instructions. Whether you’re sewing or overlocking the fabric I strongly suggest you have the whole piece supported on the table in front of the machine rather than feeding up from your lap. This is to prevent the piece becoming stretched as you’re sewing and possibly causing it to become misshapen.
If you find, as I did, that there’s a slight discrepancy between two seams (assuming that it isn’t an error in cutting or adjustment of the pattern) then pin it with the excess on the underside so that when you sew the feed dogs will take up the ease.
My photos should make it clearer, a good press will help steam out some of the excess too. Also, to minimise the risk of making a shiny patch on the fabric make sure you use a pressing cloth, you can often buy silk organza ones although I have a piece of plain fine pure cotton lawn which I’ve overlocked around the edge. I use this when I’m pressing darts or turning points or corners out too.
To sew an invisible zip into the diagonal seam across the back I machined the seam closed but I used a long basting stitch just for the section where the zip will go. This stitching will be removed later.
Once the zip was in and side seams sewn up I checked the fit on myself. I cut a UK 16 and overall I’m happy with the fit and apart from the length I made no alterations to the bodice. Because I made the linen version first I already knew that the shoulders were a bit too broad for me and the sleeves dangled too much off the crown of my arm. I calculated that I needed to remove approximately 3cms to lift them up to a slightly better position. I found I didn’t need to alter the sleeve head though, fortunately it still fitted into the armhole. Another thing I did decide at this point was that the sleeve needed ’something’ else so I mocked up some small pleats and pinned the sleeve into the armhole to try out the effect.
After making the pleats in the sleeves and sewing up the underarm seam I used a ‘pin hem’ to finish the edge. This is similar to a simple rolled hem but even narrower. Begin by stitching a turning of approx 1cm very close to the edge, trim this carefully
I love the 1930s/40s vibe of this dress, the drapey qualities of the fabric enhance the bias lines of the skirt in particular. I really enjoyed the challenge of putting the dress together, there are no particularly difficult techniques as such but it’s an interesting puzzle which you’ll need to spend a little time concentrating on, you’ll be rewarded with a striking but really wearable dress.
Thank you to Trend Patterns for gifting me the pattern, there was no expectation to write a review. You can read my previous review of the Square Dress pattern here. The fabric was provided by Lamazi Fabrics in return for a review which is also published on their own website.
I hope you find some tips and advice in here that might be of use to you if you’re thinking of using a fabric that needs a bit more forward planning than you’re used to. Trend have created another beautiful pattern with stunning and unusual details but the pieces cleverly work with the grain of the fabric so that working with the bias cut is a lot easier than it usually is. They have been gradually increasing their size range too so the TPC26 comes in UK sizes 6-22.
Quite a long blog this time so thank you for reading this far and, until next time,