Simple Sew Chelsea Collection blouse hack.

A lot has happened since I wrote my last Simple Sew blog post, Christmas for one thing, and I had a lovely holiday in the sunshine too but now we are all confined to our homes because of Covid 19. Without wishing to trivialise the gravity of this situation, one of the side effects of it is that you might have more time to sew. 

I’ve had a rummage through my Simple Sew patterns to find one which I haven’t already shown you, and which has opportunities to hack, and I settled on the Chelsea Collection. This is a capsule wardrobe of a short sleeve blouse with two variations, a pair of trousers and a button-front skirt in two lengths. I liked the blouse with it’s shirred sleeves and keyhole back detail but I decided to mix it up a little by adding a button front. Normally we are able to select fabric from a couple of generous sponsors but I wanted to ‘shop my stash’ to find something this time. I found a very pretty vibrant floral John Kaldor cotton lawn which I think I picked up from a swap table sometime and I knew would work well for the blouse. 

I didn’t want the blouse to be overly tight so, after checking my measurements I opted for a larger size than I’ve made previously. If you’ve been a regular reader of my posts you’ll know that I tend to check Simple Sew patterns for any discrepancies before I start. There didn’t seem to be any glaring ones but I just added a slight curve to the back hem so that it dipped in the same way as the front and I trued the shoulder seams so there was a smooth flow from front to back. 

Adding a curved hem to the back, I measured the distance from the lengthen/shorten line on the front then made the back the same amount, curving the line gently upwards to the side seam.
trueing the shoulder seams

As I wanted to alter the front significantly I had to make some changes there first. In order to create a button-stand I simply added 2.5cms to the centre front all the way down what would have been the fold. [2.5cms was a fairly arbitrary figure because it depends really on what size buttons you’re using, a general rule of thumb is that the bigger the button the bigger the button-stand needs to be so that there’s enough overlap and the garment doesn’t end up too tight because the overlap isn’t big enough.]I was able to do this by drawing directly onto the tissue before cutting the piece out as there was enough space to do so.

adding the button stand to the front

If you’ve already cut a pattern that you want to add to just stick some extra paper to the centre front fold line, or trace off the whole piece again adding the extra. The original front had a facing for the neckline so now I needed to create a new facing which would neaten both the neck edge and the button-stand. To do this I simply traced off the whole of the new front opening including the neck edge and made the facing a depth of 7cms all the way down from shoulder to hem, with a smooth and gradual curve. The photo should make this clearer. The back neck needed a new facing too because the existing one took the armhole into account. Again I traced off the section I needed making it 7cms at the shoulders to match the front facing. 

The final change I made was to lengthen the sleeve a little and add some more fullness to it. I started by making the sleeve 5cms longer and then I drew 3 vertical lines on the pattern at approximately the front notch, back notch and shoulder seam points. [Depending how much extra fullness you want to add to a sleeve you could use more places than this but do try to space them evenly apart.] Next I cut up each line from the bottom until I reached almost the top, I left this very slightly attached. With the piece flat on the table I spread the bottom of each slit by about the same amount, probably about 4 cms, then taped slithers of paper into each gap.

First I added the extra length and then drew the vertical lines where I wanted the extra fullness.
Next I opened each part to add the extra being careful to keep the pieces flat and not twisting or wrinkling up, put extra pieces of paper under the gaps. Once you’re happy tape them in position,
Once I had added the extra I cut the piece out.

If you don’t want to cut the pattern up you can do the same process by still marking the vertical lines on then pivoting the uncut pattern at the top of each line, use a pencil or your finger as the axis. Draw or trace around the first section, which remains stationary, then each subsequent section after you pivot it to so that you get the extra fullness being added at the hem. Opening up the wedges in this way means you’re adding fullness to the hem but not the crown of the sleeve, if you want extra fullness in the crown spread the whole piece more or less parallel. The grainline should run equidistant down the centre of the new piece (unless you want to cut it on the bias)

Having done all this I cut it out and was ready to sew! 

I started by joining the shoulder seams of both the blouse and the facings (which I’d interfaced and neatened) then I attached the facings to the neck edge, turned, understitched and pressed. The keyhole back calls for a small rouleau tube as a button-loop which needs to be inserted at the same time as applying the facing although you could choose to make a hand sewn thread loop and stitch that at the end. In fact it isn’t even vital that this is a functioning loop if you’ve got a front opening, the keyhole is purely decorative now. 

I put the blouse onto Doris to check it was looking OK and this was when I found that the keyhole appeared to be bagging outwards quite significantly. I decided not to do anything at this point and I would check again once I had sewed the side seams and put the sleeves in, then I would get a better idea by trying it on myself. 

Checking the front neck
With the loop pinned I discovered that the keyhole didn’t sit flat.
It seems to stick out quite significantly on Doris.
If the button isn’t done up it would look like this.

I made three rows of shirring on the sleeves next, using my quilting guide to make sure the first row was 5cms from the bottom edge, the next two rows were then sewn parallel to the first. [Refer to a previous blog post on how to sew shirring if you haven’t done so before] Next I sewed up the sleeve seams and pin-hemmed the bottom edge to give a neat finish.

I positioned the needle 5cms from the cut edge and the quilting guide helps me as a visual marker to keep it parallel all the way.
Shirring is stitched from the right side so that the elastic is on the reverse. Use a long straight stitch, secure both ends and then apply plenty of steam to shrink up the stitching further.
finished sleeve

After sewing up and neatening the side seams I inserted the sleeves. At this point I tried the blouse on again to check the keyhole on myself and, with real shoulder blades under it, it didn’t seem so noticeable. Two other things struck me though, the blouse was a little too big so I took it in on the side seams and also the blouse was a bit shorter than I expected. In order to take as a small a hem as possible I made some bias binding from offcuts of the fabric then stitched it (folded in half lengthways and with the cut edges together) to the hem using a narrow 5mm seam allowance [This is a useful finish to any hem or edge where you need every spare centimetre of fabric.] Have a look at the photo which shows you how to get the ends of the binding enclosed within the front facing. I turned the binding up and top-stitched in place. 

If you’re adding binding when there’s also a facing pin it like this so that the end is neatly enclosed inside the facing when it’s turned right side out.

Finally, I found some ‘vintage’ buttons amongst my treasure trove and there were just the right number meaning the whole blouse had been sourced from what I already have!

Well I hope now that I’ve made it that I’ll have a chance to wear my Chelsea blouse somewhere other than in my own garden this summer, who knows? Maybe you’re reading this long after the emergency ended and life has returned to some sort of normality, although it definitely won’t be exactly as it was before.

Sewing our own clothes is an activity which gives us so much enjoyment for a variety of different reasons and, right now, the simple act of creating something is chief amongst them for me. It’s absorbing and the problem-solving gives me something else to think about.

I think the keyhole back is, by and large, just about acceptable when I’m wearing the blouse. I also think the cure could be to add a centre back seam instead of cutting on the fold so that the point of the keyhole could extend beyond the centre back line, this would hopefully bring the button and loop closer to one another when they are done up…this is just my theory based on experience and I haven’t tried it out. It’s such a nice little detail that I’m disappointed it hasn’t worked out quite right. I also regret not reading my fellow Simple Sew bloggers reviews of the blouse because then I would have known how short it comes up, personally I would add a minimum of 8-10cms to the length next time.

The sleeves are pretty and feminine but maybe they are a little too girly, the jury is out…

Until next time, happy sewing

Sue

Simple Sew Amelia tea dress hack.

The Amelia tea dress isn’t one I’ve sewn before but Jane who comes to my sewing class had made one last summer and I remember liking the shirred elastic midriff section. The brief for our makes this time was ‘festive’ (we usually don’t have a brief, it’s free-choice) Bearing this in mind Bobbins n Buttons had offered to provide me with fabric so I had a browse on their website and selected the Lady McElroy ‘beauty and the bees’ stretch velvet. 

The pattern isn’t intended for jersey but it is simple shapes and a bit of gathering which I knew would still work well, what you don’t want is a fabric that’s too thick or stiff though because the shirring won’t work properly. I planned to hack the pattern a bit so I decided to add long bishop sleeves as it’s winter, I also lengthened the skirt (more on that later) and of course I added pockets! 

Because of the distinctive large print I opted to remove the centre back seam and put the zip into the side seam instead, this was to save me the hassle of trying to pattern match the print across the zip. Because I’d removed the CB seam in the bodice I took it out of the skirt too, for the same reasons. If you’ve got a tricky print to match over a seam like this consider whether you can move the zip to the side, it’s not much different to put in and the opening can be a little shorter but still give you sufficient room. Now I could have a line of bees central down the back (and front of course) and just needed to get a good horizontal match too for me to be really happy.

As I said before I wanted the skirt as long as possible but there needs to be a compromise between length versus flare because of the width of the fabric. If you want the skirt to be longer you’ll need to reduce the amount of flare at the hem because you’ll be restricted by the fabric width. The wider the fabric then the more scope you have. I measured how long I could make the skirt before it would need reducing at the hem and decided it would be an acceptable length. I could add around 10cms to the hem making sure the new side seams were at a right angle to each other so that the hem will run in a smooth lineI traced around a few bees where they crossed the cutting line so that I could ensure the front and back matched as well as possible. 

In order to cut everything as efficiently as possible from the fabric I first cut the skirts against the main fold-don’t forget to exclude the CB seam or the piece will be bigger than your back bodice (if you’re excluding the zip) 

Then I refolded the fabric with the selvedges into the centre to cut the bodice pieces on the folds. This is vital to get those bees running down the centre. 

From the remaining fabric I cut a pair of long sleeves. I used the pattern from another design I’ve made a few times, I measured the armhole of the dress and compared it against the sleeve I have. It was a little smaller at the crown so I added a small amount to give it sufficient widthFinally, because it’s jersey, I chose to use a neck binding instead of the facings so I cut two narrow strips which were each the same length as the CF to CB measurement of the neck plus a couple of centimetres seam allowance. 

I increased the sleeve head by 2cms, moving it out by 1cm either side of the shoulder notch.
It’s important to keep the sleeve level when you add the extra width so draw a line at a right angle to the grainline, then move the pattern piece 1cm in each direction using the line as the axis.

Ok, so I mostly followed the instruction with a few minor changes because of my alterations. One thing I did first of all was to stabilise the back shoulder seams and the left side seams where the zip was going to go with iron-on interfacing because I don’t want them to stretch out of shape. I chose to leave the back darts in although I possibly could have eased them out as it’s a stretch fabric.

stabilised side seam before the zip goes in.

After joining the shoulder seams I added my neck binding. I folded the strips with RS out along the long edge-I didn’t join them to each other at this stage-then, starting at the V, I stitched just that section into place. This way you can sew just a small part, snip into the V and pivot at the corner more accurately. When I was happy with this I sewed the rest of the binding on leaving just the CB part unsewn, then I could join the two strips in the right place and finally attach it to the neckline. Finally I neatened the edge all the way around and then topstitched it down close to the seam to stop it rolling. 

The next part is the shirring which really isn’t difficult so don’t panic. First wind shirring elastic onto an empty bobbin BY HAND stretching it very slightly as you go, put it into the machine in the usual way (you may wish to check the manual if you have an older machine in case there is anywhere else you need to thread the elastic through) Use your matching colour thread on the top in the usual way and lengthen the stitch slightly, it doesn’t need to be zigzag or anything though. Definitely try out a test piece first and don’t forget to secure the start of each new row so that the stitching doesn’t come undone. I don’t secure the other end at this stage though in case I find I need to pull the threads up any more later. You should be able to sew 8 rows of stitching parallel to each other to complete the strip. The fabric will naturally pucker up pretty well but when you’re done stitching hover the iron with plenty of steam over it and you’ll find it gathers up some more as a result. Finally knot the ends of the threads to secure.

Then you need to attach the gathered band onto the lower part of the bodice making sure it’s evenly divided as you go.

Attaching the shirred waist section to the upper bodice.

Attach the skirts (I’d sewn the pocket bags on to each side seam before doing this. I just use my handy cardboard template which I made ages ago, I just trace around it directly onto the fabric and cut out.) 

Next the zip goes into the left side seam. I sew it here out of habit as I’m right-handed and find it easier to do up that way but put the zip in whichever side works for you. After neatening both side seams separately first I sewed up the top of the side seam by about 4cms from the armhole edge. I used an invisible zip and inserted it in the usual way, making sure the waist seams matched, and then joining the rest of the side seam once I was happy with the zip insertion. I sewed up the other side seam and I was ready to tackle the sleeves.

The sleeves are set-in so I made the elasticated cuffs on the flat first using straight strips of jersey the same length as the curved cuff edge. With the strip open and RS together I sewed it once. 

Then I folded the strip in half and sewed it on the overlocker to create a channel.

 This will turn downwards to form the cuff which I slotted wide elastic through, securing at both ends. 

Finally, I sewed the underarm seams to create the sleeves which are inserted into the dress as per the instructions. 

All that’s left to do is the hem which I sewed on the coverstitch machine which is on loan to me by Pfaff at the moment. 

I’m really pleased with how the dress has turned out, it’s very swishy and has a slightly 1940’s vibe to it. I like the extra length on the skirt and the sleeves look fab. I was a little alarmed when I saw the large scale of the print but actually I really rather like the bees now. One thing I’m not keen on (and this is down to the manufacturer and not the supplier) is that they have printed a black background design onto a white base cloth. Because the cloth has a pile it means that anywhere there are joins there is a slight hint of the white showing through which is not ideal. The velour isn’t too tricky to work with as the pile is a bit flatter than velvet but it does still ‘creep’ a bit in places so if you’re in any doubt that pins aren’t enough to keep it all in alignment make sure you tack (baste) seams together. If you have a walking foot I would definitely advise using it. 

Lots of pictures swishing about!

I hope this will help you to feel inspired and perhaps have a go at ‘hacking’ a pattern for yourself. This was a very simple one but if you look at my Simplicity blouse hack you can see just how carried away it’s possible to get!

Until next time, happy sewing

Sue

Pfaff Coverlock 3.0

It’s been almost a month since I was loaned a Pfaff Coverlock 3.0 to try out so thought I would give you a ‘half-term report’ on how I’m getting on with it.

First thing to say is that it’s quite a beast! It’s a very substantial piece of machinery and so is fairly heavy as a result. That being said, this is normally the case with coverstitch machines because they are generally bigger than overlockers so the weight isn’t unusual. It does have a good-sized and comfortable carrying handle though.

Ok, so, the Coverlock 3.0 is a combination machine in that it is both an overlocker and a coverstitch machine. I’m sure you already know that an overlocker will trim and neaten raw edges and often sew the seam as well if you have 4 or 5 thread version. What you may not know is that a coverstitch machine doesn’t trim any edges, it will sew two or sometimes three rows of top-stitching on the outside of a garment whilst covering the edge of the fabric on the inside with loops of thread to ‘cover’ it. It has the advantage of being stretchy too. If you’re still not sure what I’m talking about have a look inside the hem or cuffs of a RTW jersey garment and you should see.

The first thing I had to do was not only rethread the machine as it didn’t arrive pre-threaded but I also needed to change it’s function from coverstitch to overlock. A major part of what I want to assess for you is how quick and straightforward it is to go between the functions. This is partly why I didn’t plunge in with a review as soon as I got it because I didn’t think it would be balanced or fair. Indeed, I will certainly write another review in due course after a decent amount of time and usage has occurred.

Yay! I threaded it successfully!!

Because the machine was merely delivered to me without any demonstrations I’ve needed to use the instruction book a fair bit. If you have difficulty following written instructions and/or diagrams this may not be ideal for you but there is a (silent) DVD included with very clear animations of exactly what you need to do for each of the stitch variations possible. [I didn’t find this straightaway though so I muddled through with the booklet! I’ve also since found a few very helpful You Tube videos which were useful]

I’m not going to lie, it does take a bit of time to make the changes because you’ll need to remove and reinsert the needles to different positions as well as thread the machine in different ways depending on the function. This will eventually take me less time and I’ve added Post-it notes to the relevant pages in the book so that I don’t have to keep searching for the two I’ve favoured most. The machine is capable of up to 23 stitches using 2, 3, 4 or 5 threads and up to 3 needles. So far I’ve only used the 4-thread overlock and the coverstitch but I will endeavour to use more, including the flatlock, and report back.

I decided on making a hacked version of the Tilly and the Buttons Nora top which I’ve made a couple of times before as I didn’t want any nasty complications by attempting an unfamiliar pattern with a new piece of machinery!

The beautiful jersey with an amazing ‘tie-dye’ print is from Lamazi fabrics and was my choice as a July/August maker of the month [it could be you if you tag them on Instagram] I cut the sleeve to approximately 3/4 length and also cut two cuff pieces which were again approximate, initially about 20cms in length and then my wrist measurement at one end and my mid-forearm measurement at the other. I added a couple of centimetres for seam allowance to all sides.

I’d definitely say you need to do a bit of forward planning if you intend to use both the overlock and coverstitch functions on a project because of the swapping between the two. For example, on my Nora I needed to coverstitch just the cuffs and the hem, everything else could be sewn either directly using the 4-thread overlock or on my Quilt Ambition 2.0. I opted to sew the top together first and complete the hems at the end, in the usual way although there may be times when it’s better to hem first, we’ll see.

I’ve been very impressed so far with the quality of the different stitches.

If you’re merely changing the thread colours it can be done in the same way as regular overlockers by snipping the threads near their spools, tying on the new colour and pulling each of them gently through, plus rethreading the eye of the needles. On one occasion when I altered the function I completely rethreaded but the stitch was much too loose-what had I done? It was all done correctly and yet it was way too loopy. I checked the manual for hints on troubleshooting but it didn’t make much difference. I was starting to pull my hair out when I realised I had threaded the machine without lifting the handle out of the way-the threads MUST go under it or they don’t sit in the tension discs! (Had I watched the helpful YouTube video first I would have known this…) Another thing I learnt the hard way was when the spool holder kept falling off the back of the machine and I was ready to chuck it out of the window I noticed it has to be slid sideways to click securely in position-doh!

The next two projects I made I didn’t use the coverstitch function as both the sweatshirts had cuffs and waistbands but I constructed much of them using the 4-thread overlock stitch. I used fabric provided to me by Minerva and they will appear on their blog in the new year. One of the patterns I used was the gorgeous Maxine sweatshirt given to me by it’s designer, Dhurata Davies. I’m going to make another one soon so I’ll write an individual blog on it then. [I got both tops out of 2.5m of fabric!]

For the final project I want to talk about here I took a different approach. It’s an Amy top by Brilliant Patterns and which I’ve made a couple of times before. I had a 1m remnant of loop-back cotton sweatshirting which I bought from Sew Me Something at a show for £8 and by shortening the sleeves very slightly, cutting the neckband in two parts and joining it I got a WHOLE sweatshirt out of the one metre!!

This time I set the machine up with a wide 2-needle coverstitch and I used my regular sewing machine to sew most of the seams. What I did at each stage of construction was to press the seams flat and top stitch them using the Coverlock. This meant that there would be two rows of top stitching on the outside and the raw edges were covered on the inside. This was generally OK although as I’ve yet to ‘get my eye in’ with lining up the foot against a seam or other visual marker a couple of them do waver more than I would usually like. It turns out there is a large removable flat bed included to increase the working area (it was tucked down inside the box and I’ve only just found it!!) this will support your work while you sew but it does take up a bit more room.

I like the two-part upper back of the Amy.
The hem is level at the front and a dipped curve at the back.

So to sum up (for now) I’ve been impressed with the quality of the stitches I’ve used so far on the Coverlock 3.0 and I will definitely look for opportunities to try others whilst I have it. I’ve yet to be convinced about swapping between the stitch-types but obviously, as I get more familiar with it, I should get faster at changing between them. There are few processes which have to be gone through to make the changes but I’ll probably work out an order or procedure to follow to speed it up. If you are short of space a combination machine might be useful, they aren’t cheap though. You’ll almost certainly use the overlocker stitches more of the time so possibly changing occasionally to coverstitch will be sufficient. I would definitely say you should have a thorough demonstration of the machine so that you know what is involved and what it is capable of. Unlike washer/driers which don’t do either job very well this machine does both functions to a very high standard.

Thank you to Pfaff for giving me the opportunity to try out their machine and if you have any questions about my experience so far then do ask.

Happy sewing

Sue

Simple Sew Zoe dress hack

I haven’t written a Simple Sew blog post for a few months but now that Sam Sterken has taken over with the organisation whilst Gabby is having her maternity leave we’re up and running again.

I had a bit of an idea in my head of what I’d like to do using the Zoe pattern which I already had so I chose some medium-weight enzyme washed linen in dark turquoise generously provided for us once again by Doughty’s Fabrics. I was really pleased with it when it arrived as it wasn’t too droopy but not over-firm either. Incidentally, it’s been terrible to photograph accurately, the final outdoor photos are definitely the closest to the real thing [to see how I altered the Zoe neckline so it wasn’t so wide have a look at my previous blog post in early 2018)

I drew a few sketches of ideas which all involved using the top half of the Zoe-initially I was going to extend the sleeves with wide pleated frills and keep the dress straight but I went off that idea as I felt the fabric was too firm for how I wanted it, I thought it would definitely work well with a peg-top skirt instead however. I wanted a shape that wasn’t too voluminous at the hem and by using an inverted A-line shape I could add pleats at the top but keep the hemline slimmer.

I went with option 4

I tried on one of my existing Zoes (I’ve made 3) so I could assess what length I wanted the top section, and took an arbitrary measurement of 34cms from the centre of the front neckline to where I wanted the waist, which is slightly higher than my natural waistline. As the Zoe has centre front and back seams I then measured from the top edge down to the point where I wanted the waist seam and drew a line at a right angle on the pattern across from that point. I took that line across to the side seam but at the point where the line met the side seam I made it a right angle, which creates a very slight curve on the line. Because the back neck sits a little higher than the front I matched the side seams to one another first and created a similar line across to meet the centre back seam. [It’s important that these lines are at a right angle where they meet at the side seams because otherwise you would have a slight V shape rather than a smooth line from front to back] 

I already have a skirt pattern that I’d drafted last year for a similar peg-top shape, I’d used it gathered though and I wanted pleats on the new dress. Initially I attempted to work out how to get 3 even sized pleats by folding and refolding the paper but I couldn’t quite get it. In the end I decided to cut the pieces in fabric as they were-with a slight modification for the front skirt as that piece was quite different-and then I’d work out the pleats once I was ready to attach the bodice and skirt together.

I cut all the bodice/sleeve/neck facings and assembled the bodice first. I’ve found that it’s easier to sew up the shoulders and attach the neck facings as described in the instructions but then attach the sleeves with the bodice open flat before sewing the side seams rather than in the round. The photos should help make this method quite clear. I added rows of contrast triple straight stitch to various seams as I went including around the neck [I used the quilting guide which came with my machine to do this accurately]

the sleeve is pinned on with the bodice opened out flat
the seam is pressed towards the sleeve
then the sleeve is pressed up towards the shoulder
the underarm seam is sewn up, overlocked together and then the sleeve is folded up again and top stitched into position.
On the outside I used the quilting guide on my machine to sew 4cms away from the finished edge of the neck.
top stitching on the neck edge.
the finished bodice

Next I cut the front and back skirts from the remaining fabric, plus I also cut two pairs of pockets for the side seams using the cardboard template I’ve made. [Just choose a pocket pattern that suits the size and shape that you mostly use to go in side seams and then make a cardboard version, mark the grainline and then all you need to do in future is place it on your fabric and draw around it with a pencil or chalk, it saves a paper piece getting scrappier and scrappier with constant use.]

card pocket template
the back and front skirt sections, the back is placed again the selvedge and the front extends all the way to the fold, I didn’t cut down the righthand side of the pattern as it looks here.

I made up the front and back skirt sections, adding the pockets to the side seams, then top stitched the CF seams as before, I didn’t top stitch the CB seam at this stage as I wanted to be able to sew in a continuous line with no breaks and I couldn’t achieve this until the hem was turned up too. Incidentally, as many of the seams were going to be pressed open inside the dress I overlocked the edges of most of them first then sewed the seam and pressed open. 

Next I pinned on the skirt starting by matching the centre front, back and side seams. Because I had no other markings now I played around with different positions for the pleats until I happy with how they looked. This will vary according to what size you’ve cut the waist but for mine I settled on 10cms each side of the CF seam for the first pleat and then the second and third pleats were a further 4 cms away from the previous one. I checked all the measurements to ensure that they were each symmetrical and well-balanced before I sewed it all together, overlocked to neaten and added another row of top stitching to the waist. 

Initially I tried to work out using my existing skirt pattern where the pleats would go but I couldn’t quite get my head around it so I chose to try it freehand in the fabric which, in the end, was a lot better.
the pins mark where I would match the pleats to the bottom of the bodice.
finished pleats!

This just left the hem length to check, I had opted for quite a long skirt length because I wanted the dress to be a fairly loose throw-on shape but not too baggy or undefined. I was happy with the length I’d plumped for so I used the triple straight stitch once again around the bottom and then down the CB seam, creating an angled line to define the facing which finished the slit opening. 

I’m not always super-happy with everything I make (and in truth I’ve positioned the pockets a little bit low in this dress) but I can’t wait to wear this dress during the summer! I’ve only ever worn my previous Zoes with long-sleeved tops layered underneath in chilly weather so it’s a bit of a revelation to realise that the sleeves are the perfect length for a summer dress. I think the skirt shape is more interesting than just a gathered dirndl and the lime-green contrast topstitching is a bit of fun. The linen is a great weight for this too, it will be crumply but that’s part of the charm of linen fabric…I think I may have to make more of this frock!

Until next time,

Happy sewing

Sue

Sew Over 50-has anything changed yet and what else can we do?

So, has anything changed yet in the use and portrayal of older sewers and makers in dressmaking in the media? I think the simple answer is still “no, it probably hasn’t much” but before we feel completely downhearted about it I think we should reflect on what has been happening and how we can continue to try and move things forward. Love Sewing magazine in the UK wrote an article about the situation and 10 of us featured in the photo-shoot that resulted…how about a follow-up article Love Sewing? Grainline have released a new pattern which features an older woman modelling it, are there any others doing this yet?

Since Judith Staley started the account in August 2018 it has gained over 12,000 followers and that number continues to climb steadily. I believe part of the reason for this is because people are discovering that it’s a very inclusive account where everyone in it is happy to share advice or tips, to encourage others, where the colour of our (slightly wrinkly) skin is not relevant, our physical abilities and the size of our waistlines likewise. We share our wide and varied takes on patterns both from the so-called Big 4 and Indie designers and, even though we continue to be frequently ignored by them, we will still mention which pattern it is and tag the company anyway. Generally we aren’t sore about it…There have been some successes with reposts by a few pattern companies on their Stories or feed which, if @SewOver50 is tagged, we’ll see. Make sure you always tag the account or use a recognised hashtag-they are all listed saved in Highlights on the account but by using #SewOver50 or #So50Visible for example Judith and Sandy will see you. If they repost your mention they will use the hashtag #So50thanks to acknowledge our appreciation to the pattern company involved. It’s a virtuous circle really, we buy the patterns, we sew the patterns, we share our make, the pattern company sees it and likes it, we buy more patterns! See? everybody is happy and so it goes on. We have the cash and we want to spend it on your product but if we don’t think you’re interested in us because we aren’t young/slim/pretty/etc etc insert as appropriate then we won’t buy your product any more because there are many other ways we can spend our hand-earned money instead.

Personally there are a couple of companies that I don’t bother to tag any longer because neither of them acknowledge or repost a make by anyone under the age of about 35, let alone mine. I mention the pattern and the brand so that others know which design it is but I don’t ’tag’ them. You might think this is petty but I find it very irritating that everyone these days says “tag us so we can see your makes” but then they don’t offer a ‘like’ or a brief comment to acknowledge or ‘reward’ you. I do realise that some accounts have tens of thousands of followers which makes it difficult but it can’t be impossible, and meanwhile we just continue doing free advertising for them. Somehow some companies seem to exist in a vacuum which is unsullied by their actual customers… How about a new hashtag? #NoLikeNoMention or #NoLikeNoTag?

Anyway, moving on…we’ve been asking recently on the SewOver50 account if you have experience of pattern reviewing, pattern testing or blogging about your makes? How was this for you? How did you get started, were you approached or did you volunteer to a call out of some kind? Any or all of these would be a really good way of continuing to have older faces in the mix.

Obviously I do all of the above because that’s why I write this!

So, looking at the first area ‘pattern reviews There are several ways you can get involved in this. Firstly decide on a pattern you think people would be interested in hearing about-you may base this on your experiences with it which might be great or they might be terrible! Either way, if you think you’ve got something to add to the conversation then get writing. There are two places which immediately spring to mind to do this and they are The Fold Line online community which is UK-based, and the Pattern Review which is in the US. BOTH are fully accessible from anywhere in the world so this doesn’t mean they are exclusive to those areas, you just might find more ‘voices’ from one or the other. They are VERY different from each other starting from the way they look, The Fold Line feels a little more ‘youth’ oriented and ‘modern’ in its look, I find it more visually appealing and easier to navigate whereas the Pattern Review I found a bit cluttered visually but I’m sure it’s whatever you are used to, I know it’s really popular and there’s a very broad range of people posting on the site which is great. Both have options to leave pattern reviews and share photos of your makes, I’d say that Pattern Review has a larger back catalogue of reviews by virtue of being around longer than The Fold Line. I like that PR has a series of questions available to guide your review which can be helpful and keep you focussed if you aren’t sure what to write, Fold Line is all in your own words. On both you can give an ‘out of 5’ star rating. We’re trying to encourage more of you to leave reviews and these are two places you can do that, it will keep our beautiful older faces in line of sight! Do you know of or use other sites? Let us know either in the comments here or on the IG account so that we can all share and participate. Judith has asked a few stalwart SO50 supporters for their experiences and impressions of using various pattern review sites so look out for those on Instagram this week too.

I was in The Fold Line weekly newsletter earlier in the year, this could be you too!

Personally, I write my own reviews here on the blog as well as The Fold Line although I include a lot more technical stuff than I’d put elsewhere. Most of my reviews are on patterns that I want to write about because I have something to say about them, and a few are because I’m part of a ‘blogger network’ such as Simple Sew patterns. I’ve always endeavoured to be a ‘critical friend’ when it comes to a pattern review and I don’t always give 100% glowing reports, if I encounter problems or errors I will point them out and I’ll try to give alternative methods or techniques if I can. I don’t find the kind of ‘review’ which just says “yes, this is pretty and I love it” very helpful. Preferences are obviously very individual but why do you love it? does it go together well? are the instructions clear? do you need to fiddle around to get a good fit? What sort of fabric works well? All these things matter and that is what many sewers want to know before committing to buying a potentially-expensive new pattern.

I also write reviews of fabrics which I’ve been provided with free of charge by various companies including Sew Me Sunshine and Minerva Crafts. I’m not embarrassed by this because I take a lot of time and effort to write comprehensive and helpful reviews of the product, a couple of metres of fabric is a very modest reward for many hours of work for me. At this point in time I’m not paid to write by anyone.

Love Sewing magazine here in the UK includes a reader every month who sew up their own version of that month’s free gift pattern and then they feature in a professional photo shoot. I was lucky enough to be invited to do this nearly two years ago and it was great fun, if a little nerve-wracking to start with. You may know of other magazines which do this so why not email and offer yourself to them?! Another way of featuring in magazines is to try tagging them if you share photos of your makes (best if you’re using their free gift pattern or another item which was originally in their mag as they’ll be more interested) you might get used on their ‘reader makes’ pages-it’s always fun to see your face in a magazine and sometimes there’s a ’Star Maker’ prize too. Most magazines and pattern companies have a Facebook page as well as Instagram which are easy ways to share your photos, Twitter is much less about images so I tend not to use that. Make sure your photo is of a decent quality though-clean the lens, or the mirror, check the background-are there pants drying on the radiator behind you? You don’t need to be David Bailey or have a fancy camera but if it’s not a clear picture of your make they won’t use it. Again, the SewOver50 account gave lots of tips for taking successful photos using your phone and they are saved in Highlights.

meddling with modelling!
in the now-defunct Sew Now magazine

Pattern testing is another area you can volunteer for and could be your opportunity to put your skills to good use. Keep an eye open for tester callouts on IG, or have a look at company websites for a sign-up list but bear in mind that you’ll almost certainly be doing this for purely altruistic reasons, almost no one pays or rewards testers in any way other than a free copy of the finished pattern after release. (This is a bit of a contentious area-should we be more adequately rewarded?- which I’m not going into here) You’ll probably provide your own fabric and donate your time and be helping small companies to improve their products. When I’ve done this in the past the better companies give you a set of questions which is helpful because you can direct your answers to specific areas they want to know about, plus add comments of your own. They should want to know things like ‘do the seams match’ or ‘are there notches missing’, ‘could the instructions be clearer or worded differently?’ I take pattern testing seriously and it can be frustrating and time-consuming when there are problems or errors, there are now rather a lot of inexperienced people releasing patterns which are ill-thought out and inaccurate. I’m more picky about volunteering now as I’m not keen on wasting my time, I get invited to help by some companies which is flattering. You’ll be more or less expected to ‘advertise’ the pattern when it gets released which is fine if you’re happy with what you’ve made, and the very small companies are usually very appreciative of this because they generally have little or no advertising budget so they rely on people like us making and sharing.

I was invited to test the Tilly and the Buttons Eden coat
Ana of Cocowawa invited me to test her Maple dress pattern

Finally, you could have a go at exactly what I’m doing now-blogging! I started to write here four years ago as a means to document what I was making more than anything and it’s diversified a bit because I also review exhibitions and books too, or places and events I’ve visited that have a sewing context. [The word ‘blogging’ or ‘blog’, if you didn’t know, comes from ‘web log’, a form of keeping an online diary.] I don’t have a massive following, or sponsors, like some but I know many people appreciate my plain speaking and honesty in my pattern reviews. Vlogging is a ’thing’ too but I’m not interested in that, I prefer to write and I’d bore myself (never mind you!) wittering on about my latest fabric haul or whatever. There are lots of places that ‘host’ blogs, I use WordPress for which I pay a modest monthly fee but there are many others, some free, some not. If you follow other bloggers, which providers do they use? Do some research to find the site that meets your needs, if you want more bells and whistles later on, can they be added? How much will it cost? You could just write a Word Doc and copy and paste it into a Facebook page. I have a Facebook page for Susan Young Sewing but I must confess I barely use it, I don’t find Fb as engaging as Instagram. Incidentally, The Fold Line has a useful Facebook forum which is where all the discussions take place, and you can sign up for their weekly newsletters which is a round up of all sorts of up-to-date sewing and dressmaking goings-on.

So, to sum up, there are a variety of ways we can continue to get our lovely faces featured so that we aren’t overlooked and the more of us that do it the harder it will be to ignore us! Judith will be sharing ideas and personal testimonies by other Sew Over 50 ‘activists’ during the coming days and weeks so keep a look out for them. If you’ve got a story you want to share with us make sure you use the @SewOver50 tag so that it gets seen [although with our growing numbers this is getting harder so DM if it’s really important] Let’s keep plugging away together, older women have wider choices and opportunities than ever before and it’s so much better if we can endeavour to support each other in reminding the wider world that we’re here and we aren’t going to go away quietly.

I hope we can continue to inspire, support and encourage one another using SewOver50 as our touchstone because we’re bloody brilliant!!

Until next time,

Happy sewing

Sue

Sewing makes of 2018

I think this is a fairly comprehensive album of my makes in 2018, most of them have been worn a good number of times although not all were for me.

When I look back like this I realise what a busy sewing year 2018 was ( and a bit of knitting too!). Also, there seem to be a LOT of dresses and tops but very few skirts and trousers! I think this is definitely as a result of me gaining weight in the last two years and feeling self-conscious so, with the exception of my Megan Nielsen Ash jeans from autumn 2017, I really haven’t wanted to make close-fitting clothes.

I’m addressing this now, with some success so far, but the other truth is that I like wearing looser-fitting clothes anyway, although hopefully I can go down a size or two when I make them in future…time will tell.

Some of the garments you see here have been worn loads since I made them whilst others were less successful. Sometimes this was bad fabric choices, sometimes they didn’t suit me after all, also the weather became so hot that I didn’t wear the heavier items as much as I expected at the time.

I tend not to set myself up for ‘sewnine’ or other year-long initiatives because I’d rather see what takes my fancy as time passes, or whatever gap I feel needs filling. I’ve really enjoyed making a few jackets and coats this year and they have all had a good amount of wear, they aren’t something I’d done much previously. I’ll be making a couple of posh frocks soon because we’re going on a cruise in March which will need a few fancy threads in the evenings, I’ll be taking old favourites like the Maker’s Atelier Holiday Shirt and New Look 6351 trousers, and Papercut Moana to keep cool in during the day though.

Have you got sewing plans already for 2019 or are you more like me and just see what takes your fancy? We’ve got the new series of the Great British Sewing Bee to look forward to very soon and I’m sure that will inspire even more people to take up this brilliant activity with us! Dressmaking is an activity anyone can try fairly easily these days and there is so much inspiration, help and encouragement out there too, in a way it never was when I was first sewing.

I can’t wait to see the two blockbuster exhibitions at the V&A next year, Dior: Designer of Dreams opens in February and Mary Quant in April so there’s lots to look forward to there. It’s well worth considering membership this year I’d say, I’ve had excellent value-for-money from mine these past four years. [alternatively, Art Fund is also worth considering if you don’t live near London because that gives you reductions to lots of galleries and museums all over the UK, including the V&A)

I’m also looking forward to seeing a lot more SewOver50 activity from all over the world too, have you joined yet?

Maybe our paths will cross in 2019 and we can talk sewing together in real life?

Until then, happy sewing

Sue

making the Utility dress by Simple Sew Patterns.

My latest Simple Sew blog make is the fairly recently released Utility Dress, an easy-fitting style with elasticated back waist, drawstring front waist and kimono-shape sleeves. I would say that it’s suitable for softer woven fabrics like chambray, cotton lawn, washed linen or fluid viscose-types, or soft woollens for winter. Having said all of that I chose to make mine in a medium-weight jersey in a tan/black dogtooth check design from Doughty’s Online fabric store. It still works well but you just need to take care not to accidentally stretch some areas such as the neckline in particular and the shoulders. Because of the busy design on this fabric I left out the CF seam and cut the front on a fold instead, thus avoiding any difficult pattern matching down the seam. 

reinforcing the neckline with iron-on interfacing.

I reinforced the neckline using narrow strips of iron-on interfacing I cut myself but you could use the readymade type, I did the same on the front shoulder seams too. You could even use up short lengths of ribbon here for a pretty effect inside. 

As always I deviated from the method of construction a couple of times. After joining the front and back at the shoulders, instead of using ready made bias binding to neaten the neck edge I cut two narrow strips of the jersey which were slightly shorter than the neck edge [the amount will vary depending on how stretchy your fabric is. It’s usually about 85% of the neckline measurement]

Fold them in half lengthwise to form two narrow strips and then place one over the other at a right angle with the folded edges on the ‘inside’ of the V. 

Two narrow strips of fabric, overlapped at a right angle and stitched to hold them in position.

Then reinforce the V on the dress with a row of stitches just within the seam allowance, turning at the V, then carefully snip into the V up to the stitching line.

carefully snip into the V

With right sides together pin the binding to the V section only initially [see the photo to clarify this] and stitch this V section in place by about 5cms either side of the V. Pivot and open the snip as you sew to allow the binding to sit neatly and flat on top of the neck edge. If you’re in any doubt then tack this section first to prevent it moving. 

Attach the V section first, when this is right move on to the rest of the neckband. The pivot point is marked with a purple dot, This is where you rotate the fabric underneath thus opening up the snip you made and enabling the binding edge to match the neck edge.

I pinned on the rest of the neck binding double-checking the length was short enough before sewing the join at the CB. Now you can stitch on the remainder of the band knowing that the V is already sewn accurately. [Thank you Melissa Fehr for this new technique, she uses it in her activewear patterns and I’ve found it gives a nice neat result] Trim and neaten the seam on the inside if required and then you can topstitch it down to prevent the binding rolling.

neckband in position and then topstitched close to the join..

Next I ignored the method for putting the sleeves on. Instead of sewing the side seams up leave them open so that you can open the garment out flat and pin and sew the sleeve strips on more easily.

sleeve band stitched on before sewing up the underarm seam. You can just see that I had pressed the fold line on the sleeve band before I sewed the seam here. This makes it easier to fold once it’s in position. Press the seam towards the sleeve.

Now sew up the side seams including the sleeve bands. Fold the bands up towards the sleeves and either neaten/overlock the raw edge before stitching it down though the stitching line or turn the raw edge under and slip stitch in position. 

neaten the underarm seam before you turn up the sleeve band.

Moving on to the skirt and putting in the hip pockets. I used scraps of matching fabric for the pocket lining as I was concerned that the pattern might show through skirt front. This can reduce bulk too if you’re using a heavier-weight fabric.

pocket bag made with lining scraps

After the pocket bags are complete comes the waistband. I followed the instructions although I think there might be an easier way, I just haven’t worked it out on this version. Although it says there’s a chart to tell you what length to cut the elastic for the back waistband I couldn’t find it anywhere! In the end I decided to cut it half my waist measurement minus about another 6cms, to allow for the stretching and gathering up. I used a length of grosgrain ribbon to go in the front casing. 

I used a zip foot when sewing the waistband to the top of the skirt because I felt it made it less likely that I’d sew accidentally through the ribbon and elastic. 

Joining the waistband containing the ribbon and elastic to the skirt. I’ve used the zipper foot so that I could keep close whilst still making sure I didn’t accidentally sew through the ribbon or elastic. I then neatened this seam on the overlocker.

After joining the top and skirt together all that remains is to hem the skirt. I used a twin needle to do this but you could just turn it up twice and stitch. If you do use jersey fabric for this dress it’s best to sew it with a ballpoint/stretch/jersey needle so that you don’t ladder the fabric as you sew. 

This is a nice comfortable style which I’ll enjoy wearing. Disappointingly there are silly errors again in the instructions which is always so annoying, I hope this won’t be enough to put you off trying this Simple Sew style though which is a bit of a departure from their more usual vintage-style dresses. 

Until next time,

Happy sewing

Sue






Another Minerva blog already!

A bit like buses, I haven’t written many blogs in recent weeks and now several come along all at once! 

This new one is just to alert you to my next Minerva blog where I’ll tell you how I’ve made a long-sleeved version of the popular Simple Sew patterns Cocoon dress in a really lovely bright red crepe. 

It was still hot and sunny when I made it!

Crepe fabric lends itself to this style as it’s fluid, drapes well and resists creasing. Thank you Minerva for providing me with the fabric, all views expressed are my own however.

Until next time,

happy sewing

Sue

Simple Sew Cocoon Coat update

If you read my blog reviewing the new Simple Sew Cocoon Jacket a couple of months back then you might recall the crazy-big toile I made to start with. I didn’t want the fabric to go to waste and so eventually I went back to it to finish. Because it’s a checked fabric I had cut it carefully to match even though it was only for a toile originally. [Since writing the original blog its been brought to my attention that the instructions for joining the front and back pieces together are currently wrong and show the front piece being attached the wrong way up! I’ve done a little diagram below to show how it should be] I’ve realised I thought I’d misunderstood and put it together intuitively, when actually it was the instructions not me, but this isn’t very helpful to you!

IMG_8963
This is how the diagram looks on the instruction sheet

fullsizeoutput_2aa7
This is how it should go together.

 

 

fullsizeoutput_27fb
The original HUGE toile back in the summer.

Basically I deconstructed the whole thing by unpicking the seams so that it was the main pieces of fronts and backs again, I hadn’t put any facings on it so this process was pretty quick. Once I’d got the pieces broken down I placed the reduced size pattern pieces from which I’d made my denim version on top of the checked fabric, still matching the checks carefully, and recut them smaller. This time I cut out the facings and patch pockets too.

Then I simply made it up in exactly the same way as the denim coat, I didn’t use any decorative topstitching this time though.

I decided not to use the giant poppers for this one so I had a rummage in my button collection and found two HUGE buttons of unknown origin. This presented two problems, firstly I had to work out very precisely where the buttonholes should be sewn so that when the buttons are done up the checks on the front still match (because I’m like that!) and then I discovered that, because the button was far too large for the automatic buttonhole foot, there were actually NO instructions in the guide book for my machine on how to make a freehand outsize buttonhole. This caused me so much head-scratching! I goggled it on the interweb with no luck but then I remembered my friend Anne, who is an expert sewer, has the same machine as me so I messaged her. She agreed there were definitely no instructions (I wasn’t going nuts!) and whilst I’d have to work out the specifics for my particular buttonhole, she pointed me in the right direction and eventually I had two acceptable buttonholes. What a palaver!

 

 

Anyway, I finished it in the end and the Cocoon Coat pattern will be officially released in the next week as the free gift with Sew Now magazine and on their website so everyone will get the chance to try this very simple but stylish coat. [I noticed the website does draw your attention to the generous sizing and I strongly recommend you make a toile or tissue fit first] I’ve made both mine in woven fabrics but you could try it in boiled wool or another fabric which doesn’t need to be faced or neatened. What about a double-faced jersey cloth, perhaps with a soft fleecy side? You could add a collar, or turn-back cuffs? So may possibilities for such a simple garment.

fullsizeoutput_29dcfullsizeoutput_29dfIMG_8725

I’ve had lots of wear from the denim coat, it’s been really versatile because it isn’t too heavy but there’s room for layers underneath when it gets a bit cooler. What will you make yours in?

Until next time,

Happy sewing

Sue