Tips for sewing with linen jersey, a new Lamazi post

Did you know that linen jersey was even a thing? It’s an unusual fabric which you don’t see often, we all know knits are available in most other fibre types-cotton, wool, silk or man-mades for example- but I’ve never worked with it before so when Liana invited me to sew my next Lamazi project using it, and to pass on any hints and tips for sewing it, I was up for the challenge. 

This 100% linen jersey comes from Mind the Maker in a range of colours and I picked the Dry Mustard shade which is a lovely vibrant ochre. The fabric has a beautiful lustrous sheen on the right side, the reverse is duller so it makes it much easier to tell the difference between the two. It has lovely light drapey quality too and is slightly sheer.

Linen fabric is not a textile known for its inherent stretch qualities and this jersey does feel slightly different from other knits because it has only a small amount of stretch along its length and quite a lot of stretch across the width but it has very little recovery so once it’s been stretched out it will stay like that at least until it’s washed again. During construction the application of plenty of steam will encourage some of this accidental stretching to be eased back into position so, coupled with its sheerness, this means that you need to think carefully about what garment to sew with it. 

Plenty of steam will help remove most unwanted bagginess like this

The properties of linen fabric itself [cool in warm weather, warm in cold weather] mean that it would be ideal for loose-fitting leisure or exercise wear, for yoga or Pilates for example. I would definitely say it’s better to avoid anything that is particularly close fitting because areas like the elbows or wrists would become stretched or baggy with little recovery. However the fabric has a lovely drape and its fine gauge allows it to be gathered up successfully so these properties could be exploited instead.

Bearing all these factors in mind I decided to make (another) Sewing Revival Heron dress which I would hack into a blouse. The pattern has a neckline which is gathered using elastic along with raglan sleeves with deep elasticated cuffs. To mix it up further I decided to pull the hemline in onto elastic rather than have a wide smock silhouette.

First things first, I washed the fabric by hand to remove any risk of excessive shrinkage or twisting in the machine. If you want to wash it in the machine then it might be an idea to overlock the cut ends together first to form a long loop and place it into a large washing bag to protect it further. Alternatively you could press it on your ironing board with plenty of steam instead. If at all possible it is better to dry the fabric flat, and certainly don’t wring or twist it. All of this might sound off-putting, and it is clearly not as straightforward as chucking a nice stable cotton into the machine but this is a luxurious fabric and deserves to be treated and handled carefully in the preparation. When it comes to cutting out your pattern pieces lay the fabric as flat as possible, handle it gently and don’t pull it about too much, especially if you decide to fold it. I made a whole back pattern piece for my top so that I could cut it flat, another appeal of the Heron pattern for me is that it has just three pieces so it’s a relatively quick sew usually. 

After cutting all the pieces the first thing I did was stabilise all the raglan shoulder seams using some iron-on seam tape, I did this to prevent any unwanted stretching before I sewed the sleeves in later on. I added small squares of iron-on interfacing to reinforce the bottom of the opening on the centre front seam too. I also decided to press all the folded parts of the casings/ruffles for the neckline, sleeves and hem before sewing anything together, just so that I was handling the cut-out pieces as little as possible, again to prevent unwanted stretching before they got joined together. I also tacked these folded parts into position temporarily. All this might sound excessive but I wasn’t in a rush, and I found the slow and considered processes very soothing at quite a difficult time. 

iron-on stay tape to prevent unwanted stretching of the raglan seams
I pressed and tacked casing/ruffles before joining the sections together later on
reinforcing the bottom of the neck opening with small squares of iron-on interfacing.

Something else I did before commencing was check on fabric scraps which needle and stitch-type would give me the best results. A ballpoint needle suitable for stretch/knits/jersey is essential to prevent snagging which could lead to laddering of this delicate fabric, and I found a short straight stitch was better than a narrow zigzag but you must do what works best on your own machine. You could sew a garment together entirely on an overlocker but be aware of the lack of rebound this fabric has so if it gets stretched or misshapen while it’s being sewn then it’s probably like that permanently. I also tested the overlocker finish before diving in for the same reasons. If you don’t have an overlocker this fabric is fine enough that where possible you could probably sew self-neatening French seams, or a wide zigzag might work but just be careful it doesn’t chew up the edges. If you have an overlock stitch option on your sewing machine and/or a special foot to sew an overlock-style stitch then definitely use them. Test all options before making your choice, the time taken could save you upsets later on. I slipped some folded strips of paper underneath the seam allowances when I pressed them to minimise any chance of the seam showing through on the front

testing stitches and overlocking
I popped two strips of folded paper under the centre front seam while I pressed it so that there was no show-through or unwanted shininess on the right side.

If you have a walking foot for your machine this is definitely a fabric worth using it for, even if you don’t it’s a good idea to use plenty of pins. I’m not a fan of mini-clips because I think they are too heavy and get in the way, this fabric is lightweight and I think mini-clips could distort it while you’re sewing but it’s up to you. Tacking seams is always an option too of course, any technique that prevents the fabric shifting while you sew basically.

If you’ve followed my blog for a while you’ll know I’ve made a few Herons before so the construction was straightforward, the only area I did differently was to create the ruffled hem with a wide elastic casing. I couldn’t decide between my planned 2cms or 1cm wide elastic initially so I tested with the two widths to see which I preferred-I chose to stay with the 2cms width as planned. 

testing which elastic width I preferred for the hem, this was the narrow one (the fabric scrap is wrong side out!)
and this is wider width, it’s the one I used at the hem in the end.
using a bodkin to insert the narrow elastic in the neck casing.
checking the gathered neckline on the stand
I used this quilting attachment on my machine so that I sewed an accurate parallel width for the elastic casing
close up of the elasticated hem casing

To sum up, I’m really pleased with how my first experience of sewing with linen jersey has gone, I’ll admit I was a little nervous because Liana was putting her trust in me with an expensive fabric but taking the time to plan and test, and use my existing knowledge of working with knits definitely helped. Because of the sheerness of the fabric Lamazi also provided me with a metre of Atelier Brunette crepe viscose in Ochre to make a camisole to wear underneath, I used the Simone camisole and trousers pattern by Maven which is a very quick make and a very useful garment to wear on its own or underneath other garments. The crepe viscose is a beautiful quality fabric with lovely handle and drape but be aware that there’s a disappointing amount of creasing, you might want to take that into account when planning, for example if you’re making something you’ll spend a lot of time sitting in.

all finished

As always, I hope you find my hints and tips helpful if you choose this lovely fabric, I wouldn’t recommend it to a novice sewer because some experience of sewing with other similar fabrics is definitely an advantage, plus it would be shame to end up with a costly mistake, but if you’re looking for a new challenge to add to your repertoire this could be a good start. I’ll launder the finished garment either by hand or in a wash bag on a gentle cycle in the machine. I’ll dry it flat too and store it that way, I don’t want a coat hanger to make it misshapen. If you’re a person who prefers not to worry too much about their clothes or their maintenance then this might strike you as overkill, and that’s fair enough, but I don’t think it hurts to have a few special things in our wardrobes which were worth the effort to make for ourselves. 

I’m looking forward to wearing this top as autumn is fast approaching (did summer ever arrive!?) thank you to Lamazi for providing me with the fabric to review.

Until next time, happy sewing,

Sue

A return to blogging with a Kingfisher top from The Sewing Revival

There’s been quite a lull in my sewing and blogging of late due to a distinct lack of motivation and generally feeling meh about everything. I don’t know about you but I’m utterly cheesed off with the persistence of the ‘Rona and, whilst I really try to find the positives as much as I can, there comes a time when I’m all out of good thoughts.

Anyhoo, I’ve finally managed to get my act together and to cut out and sew something which is worth blogging about!

You’ll know I use The Sewing Revival patterns a lot, and especially because they are SewOver50-friendly in their representation. Janine kindly offered me a copy of the new and improved Kingfisher top recently so here are my thoughts on it. The original version was one of the first in the Sewing Revival collection and it now features extra variations including 3 sleeve lengths and additional ruffles and frills to gussy it up.

Initially I’d settled on using a length of fabric I bought recently but in the end, whilst searching-sorry-shopping, my stash I came across a length of batik-printed lightweight cotton which had originally been a dress. I bought it as a remnant which was in two different-sized pieces pieces so I joined them right across the weft to make it useable. From that I turned it into a simple ‘pillowcase’ dress with a gathered drawstring top and hemmed at the bottom. Needless to say, this being England, I didn’t get a massive amount of wear from it because our climate is so unreliable. Sadly I don’t seem to have a photo of it now so you’ll just have to believe me.

The Kingfisher has raglan sleeves which are always so nice to make because they are simple and quick to construct. One of The Sewing Revival’s trademarks is to mix a stretch neck band, cuffs or hem with a woven fabric and this top features a ribbed, rounded neck band. But first I had to get all the pieces out of a length of fabric with a join across it at about 50cms in, plus a tear at right angles to the selvedge in another place AND a small hole just near that! I calculated that I could get a pair of 3/4 length sleeves but one would have to have the seam running horizontally across it. Another new feature of the Kingfisher is additional small ruffles to add so, instead of placing them vertically on the sleeves, I opted to cover the seam with horizontal ruffles, that way way both sleeves would look the same. After a bit of pattern Tetris I got everything I needed out including the ruffles. I started by making the sleeves.

Inside the sleeve with the exisiting join running horizontally

Because of the limitations of the fabric the ruffles were only 5cms wide so, in order to lose as little of their width as possible, I finished each edge with a rolled-hem finish on the overlocker. Check your instruction booklet because I’m sure many models will offer this feature, it will involve a few simple adjustments to the settings to achieve. A rolled hem is a quick and attractive way of neatening fine or lightweight fabrics when you can’t afford to lose too much off the edges.

Each ruffle was cut twice as long as the width of the sleeve because the fabric is quite fine and will gather up well. If you are limited for fabric (mine were cut on the straight grain) or if your fabric is quite stiff or thick, then 1.5x the width will be fine. I sewed a rolled hem on both edges of the sleeve ruffles and then ran two rows of a long gathering stitch along the centre line. Make sure the gathers are evenly distributed before sewing the ruffle down, I used a zigzag stitch to sew the ruffle in place.

I created a cuff to finish the sleeve ends by cutting two pieces of fabric from along the selvedge and sewing them on. My original plan was to create an elasticated cuff using a casing but then inspiration struck(!) and I sewed three rows of shirring instead.

Shirring works best on lighter-weight fabrics such as soft cotton-types [lawn, batiste, voile, Swiss Dot, pique, poplin if it isn’t too stiff] also most viscose/rayons, many silks, and fine woollens such as challis. This isn’t a definitive list by any means, basically nothing too thick, or stiff or overly ‘bouncy’. As with anything you’re unsure about I’d strongly suggest sewing a few samples first to see how it goes.

To begin (and these are very much my own thoughts on shirring, you will find many others which might vary to these-trial and error before you start is the best plan of action) you ideally need a bare minimum of 1.5x the eventual finished measurement but as a rule of thumb I would say at least 2 or 2.5x your finished measurement, especially if the fabric is very fine. I also wrote advice on shirring the back of a sundress in a previous blog post which you can still read here.

Gently wind shirring elastic onto your bobbin by hand, do not stretch it as you wind, you will use regular sewing thread on the top as normal. Set your stitch length as long as possible and, sewing on the right side of the work, make sure you backstitch at the start to secure your threads then sew your first row of stitching. Do not backstitch at the end of the row, carefully remove the sewing by gently pulling the elastic out so that there’s enough to tie off the ends eventually. Repeat by sewing parallel to the first row of stitch as many times as you require, I’ve just done three for the cuff. You could draw on the lines using a marker pen or chalk if it will help, I just keep the edge of the foot in line with the previous row of stitching. The work will gradually start to pucker up as you increase the rows. The photo above shows you what it looks like on the reverse.
This is the right side of the cuff, wherever possible work with the fabric flat and then joint it in a seam or to the next piece it’s connected with. It won’t be gathered up enough to start with so hover your hot iron with plenty of steam over the area and it will pucker up a lot more. When it’s gathered as much as it’s going to tie off or backstitch the threads/elastic to secure.
In the photo above, the top cuff is before the steam was applied and the lower cuff is afterwards, you should be able to see that the stitching is a fair bit tighter-looking.
Next I added small ruffles to the front raglan seams, also neatened with the rolled hem finish just on one edge. The rest of the Kingfisher was very straightforward, the ribbing band went on neatly and gives the neckline a nice finish. You could also use bias binding or make facings if you don’t want to deal with stretch but I like it like this.
Close-up of the finished neckline, I think I bought the navy ribbing from Lamazi Fabrics a little while ago.
Sleeve ruffle

I cut this top in a UK10 so it’s a closer fit than some tops I’ve generally made but I’m really happy with the fit, there’s still ample room for comfort and movement. From a fabric that was languishing in a box I’ve concocted a casual top I can wear in warmer or cooler weather.

Thank you to Janine for providing me with the pattern, I hope my review will be helpful, for a such a simple shape there are so many possibilities with it. If you haven’t tried any Sewing Revival patterns I’d definitely suggest you pop over there and take a look, and if you choose to follow any link I’ve created in this post or previous TSR ones, and you then make a purchase, I will receive a modest fee from it. You can also read my previous reviews for the Sidewinder pants, the Heron dress plus a hack, the Bellbird top and the Fantail top and it’s follow-up. If you want any more inspiration use the hashtag #KingfisherTop on Instagram or Facebook. I’ve got plans for a deep-cuff version later in the year, just so long as I don’t have another creative slump…!

Welcome back and thanks for reading this far, I’ll try not to leave it so long next time!

Until then, keep sewing!

Sue

Simple Sew Palazzo Pants updated

In 2019 I decided to try something different to dresses from the Simple Sew pattern collection for my blog post so I chose the wide-legged Palazzo pants. 

I always have a look at any posts or reviews about a particular Simple Sew pattern first to check if there are any pitfalls I should look out for which might influence my decision, or how I tackle making it, and the overall opinion of trousers was positive. I sorted out some fabric from deep in the stash, it’s a viscose from the now-defunct Adam Ross fabrics which has a good drapey quality, although I know it will crease so I’ll wear these permanently standing up! 

There are only 4 pattern pieces to the trousers-front/back/waistband/pocket- which makes them very simple to lay up and cut out, you could even leave out the pockets if you’re short on fabric but why would you leave out pockets?! 

I checked my measurements against the chart to decide my size, I also measured the pattern pieces to get some idea of the ease involved but I was optimistic they would be generally OK. If you’re very unsure, or between sizes, I’d suggest you make a toile that’s about mid-thigh in length to check the fit and comfort around your waist, hips and body length. Leave out the pockets at this stage, there are darts in the back and the front is flat, you could insert a zip in the back if it makes things easier to fit yourself but I didn’t bother. Always sew a toile as accurately as you would the garment itself because if you don’t bother cutting properly or following the seam allowances how will you know where the problems lie? That’s the whole point of a toile! Make any adjustments on the toile and transfer the changes to the pattern pieces. There are no lengthening/shortening lines marked on the midriff area of the pattern so I suggest, if you need to make either of these changes, drawing a line at a right angle to the grainline at a point midway between the waist and crotch level. Fold out or add in length through this line. There is a lengthening/shortening line for the leg length however.

It wouldn’t be a Simple Sew pattern if there weren’t some errors or anomalies to keep you on your toes and this is no different. On the back piece the pocket placement notches are only printed on size 8 and none of the others. Either transfer the markings to your size or remember to snip them when you’re cutting out the back.  

The notches don’t feature on all the size lines so transfer them across as required.

The lay plan for cutting out shows the main pieces interlocking, which is fine if you have plain or multi-directional fabric but don’t forget to keep the pieces running the same way if you have a distinct one-way print. Also, I didn’t cut out the waistband until I was happy with the fit of my trousers as it’s very shaped piece and if it’s too big or too small you’ll probably need to cut another. Don’t forget to make a snip for the centre point on the waistband, it could have done with a notch for the side seam position though as there isn’t one so it’s a bit of guesswork.

I’m not normally an advocate of overlocking the edges until they’re sewn up [because if you aren’t careful you can easily lose too much seam allowance in the trimming and when you join pieces together you could start to make the garment too small, plus your notches disappear] but, as many of the pieces here require the seams pressed open and flat, I overlocked most pieces first this time. 

You will find that for instructions 4 and 6 the words don’t match the diagrams but the drawings are correct 

Next the pockets go in (unless you wish to check the waist/hip fit first in which case tack or machine baste the side seams and leave the back open where the zip will be inserted in order to try the trousers on) The description for the pocket insertion is a bit vague, I’ve made a second pair since writing this piece originally and found it quite unsatisfactory which is why I have updated my advice.

Neaten the lower edge of the pocket bags first then pin to the trouser fronts matching the ‘opening’ notches. Next stitch in place from the waist to the bottom edge of the pocket bag using a 12mm seam allowance (see my notes on the photo above) Repeat with the trouser backs, then neaten the seam edges all the way down enclosing the pocket edges too. On the front only, understitch the pocket opening. Now you can pin the fronts to the backs and sew the side seams shut using a 1.5cms seam allowance, not forgetting to leave the pocket opening unstitched! Finally, carefully sew the bottom edge of each pocket bag closed otherwise your sweets will fall out inside your trouser leg!

After I’d assessed the waist size (comfortable to loose) and crotch length (comfortable) at this point I cut and interfaced the corresponding waistband [for some reason there were two waistbands printed out but I could find no discernible difference between them so just ignore one and cut a pair in fabric plus one interfacing] 

The reason the waistband goes on before the zip insertion is because the zip runs right up into the waistband to finish at the top, there’s no overlap allowed with button or hooks and eyes. You could use the overlap method if you prefer but you’ll need to add some extra length to the waistband on one end to allow for the overlap. 

The lack of indication of the side seams on the waistband means you’ll need to pin carefully to evenly absorb any fullness of the trousers to ensure a good smooth fit to the waistband. [the side seam is probably at the halfway point but not necessarily, especially if you’ve made any fit adjustments to the waist] 

With the benefit of hindsight I would make the waistband in two pieces, a front and two backs with the join at the side seam. This is for two reasons, first, it will allow you to make adjustments for fit more easily and, secondly, I’ve found the centre back has become slightly pointy and misshapen both times I’ve made these now. I believe this could be because the length and curve of the waistband means that it the centre back is very off grain, usually the centre back seam would be cut on the straight grain which gives it stability.

The instructions and illustrations for inserting the zip are reasonably clear however there seems to be a contradiction with an earlier instruction which tells you to sew up the back crotch seam. Illustrations 13-15 appear to have the CB seam unsewn and 16 tells you to sew it up after inserting the zip but previous diagram 6 tells you to sew it up! No wonder I got in a muddle!! My suggestion would be, if you’re using an invisible zip as suggested, leave the CB seam unsewn AND ignore instruction 11 to sew up the inseam until after you’ve inserted the zip. Alternatively, use your preferred method of inserting an invisible zip. Before sewing the waistband down I added two hanging tapes to each side seam so that I had an additional means to hang the trousers up if needs be.

On my second pair I’ve added a small button and loop inside the waistband because I found the zip a bit of a faff to do up without anything at the top of it.

you can also see here how the waistband rises to a slight point on each side in spite of it being fully interfaced. It isn’t the end of the world but I’m a bit cross it’s happened a second time, CBA to fiddle with it too much though…

Hopefully you’ve now arrived at a finished pair of trousers which simply need hemming. After checking the length wearing shoes (they come up pretty long) you could use the simple rolled hem finish as per the instructions or, as I did, leave a sizeable hem of about 5cms to give weight to the very flared leg width. I overlocked the edges to neaten and then used my blindhem stitch with the appropriate foot on the machine to finish [incidentally the photo is of a different project] I don’t use this technique often but it’s a good, and quick, finish on hems that don’t have too much, if any, curve. You could also slip hem by hand of course. 

Different project but still blind-hemming set up

The Palazzo pants are worth persevering with as they have a pleasing smooth fit over the waist and hips which is very comfortable and the leg is wide without being crazy-big. You could shorten them to culotte length very easily, they would work well in a variety of fabrics including linen, chambray or crepe, fabrics with a bit of drape and fluidity will look nicest as you don’t want to look like Coco the Clown!

I’ve made my second pair from a remnant of printed linen/viscose mix I bought from Lamazi recently.

I’m wearing them here with a top made from broderie anglaise that I found in a whole collection of fabric I was given by a friend. Her mother had been a wonderful dressmaker and I found the fabric pre-cut as this simple top which so I just sewed it up.
I’m wearing them here with one of my trusty Camber Set tops from Merchant & Mills
Same Camber, different trousers!
I cut this pair slightly shorter overall so that they aren’t so long if I wear them with flat shoes.

Overall I’m pleased with these trousers, they are a good fit and make a nice alternative to a skirt or close fitting trousers especially in warm weather.

I noticed that this particular post gets a huge amount of traffic so I hope this update clarifies any issues you might have had with the pattern. In fairness, it might have been updated and corrected since my copy was produced in which case you may be able to disregard some/all of what I’ve written!

Until next time, happy sewing

Sue

Fantail follow-up!

I published my review of The Sewing Revival Fantail top recently and since then I’ve made a second using an alternative finish which I thought I would share with you.

the first Fantail top

This second version uses a ribbing finish on the neck, cuffs and back hem instead of hemming or elastication. I’d bought some Art Gallery viscose from Sew Me Something with an interesting graphic design and then my fellow @SewOver50er Kate @stitchmeayear generously offered me some grey ribbing, she had more than she needed. It turned out to be the perfect match and I couldn’t have planned it better if I tried.

There are separate pattern pieces for the ribbing cuffs, neck and hem and, although the same front, back and sleeve pieces are used, there are very slightly different cutting lines for the sleeve.

I had bought 1.5m of the graphic print and it has a fairly distinct one-way design which meant I needed to place each pattern piece carefully to try and get a reasonable match whilst not wasting too much fabric. I was able to do this by folding over one selvedge by just enough to position the front and back pieces along the same fold. This left a good sized piece from which I could individually position and cut a pair of sleeves whilst still just about getting a good match.

Sewing the Fantail with ribbing is very slightly different to the woven version. First, the deep ribbing band is sewn on the back in place of the narrow hem [I’m not sure if there’s a small discrepancy in the pattern or my cutting out but on both my versions I’ve found there to be about 5mm too much fabric in the back compared to the front when joining the side seams]

Like the first version I sewed the ribbing band onto the neck after joining the raglan seams and before sewing up the side seams. As I probably explained in the previous post, I always find it’s easier to put a facing, binding or whatever neck finish on whilst everything can still be laid out flat unless there’s a technical construction reason for doing it later.

The main reason for writing this second post is because I want to show you the way I turned the band at the hem-I forgot to take photos as I was making the first one! It’s a really neat way of of finishing the bottoms of the side seams and can be a useful technique in other places when you’re sewing different hems or edges together because it gives a crisp and level finish to an edge with the seams enclosed. The photos will help make more sense.

Pin the side seams together like so first, the raw edge of the deep elastic casing for the front is already pressed up by 1cm and the bottom of the ribbing is lined up against the notch for the casing.
Next, fold up the front so that it sandwiches the ribbing like this, pin in place. Now sew the seam starting at the fold on the hem. If you haven’t used this method before you may want to sew one side first and check it to make sure you’re happy with it, it can be a little confusing initially but it’s worth persevering.
Turn the hem to check it is level and, if you’re happy with it, neaten the seams however you wish. This is before I neatened the side seam but it will look like this on the inside.
The outside will look like this, so neat!

One other slight change I made was to the width of the ribbing cuffs, I cut the UK 12 pieces but they were much too baggy for my wrists so I shortened them by 5cms so they aren’t so wide and gapey.

At the moment I haven’t edge stitched any of the ribbing like I would do normally on knit garments. Because this is a combination of woven and knit fabrics I don’t want the woven fabric, at the neck especially, to end up puckered where its attached to the band so I’ve left it for now [and I don’t want holes if I had to unpick it]

The ribbing is currently not edge-stitched in case it causes puckering

I don’t normally post two of the same thing in such quick succession but I wanted to share the hem tip more than anything. I fully anticipate making a knit version of the Fantail at some point, or a short sleeve one in something really light and pretty…That’s what I enjoy about Sewing Revival patterns, so many possibilities if you have the imagination.

Until next time, Happy sewing

Sue

My latest Minerva make-Tilly’s Tabitha T-shirt dress

I seem to be constantly attracted to teal/turquoise/duck egg shades recently so this Art Gallery organic cotton jersey for my recent Minerva post looked perfect when it hoved into my field of vision! 

I’ve used Art Gallery knit fabrics in the past and the designs and fabric, whilst fairly pricey, are lovely quality. This particular jersey is an organic cotton (with a little Elastane) and very soft, a lighter weight than many so it would be good for children’s and babies clothing as well as adults. I love the print, I think it’s a vaguely ‘Tribal-esque’ graphic stripe and I quickly decided to make a Tabitha T-shirt from Tilly and the Buttons book ‘Make it Simple’ which I’ve made a few times before but to try out the dress hack version for a change this time. 

I traced off a new copy of the pattern using the horizontal lines indicated across the bodice specifically for the dress. I’m not long in the body but I thought it looked a little short so I added an extra 2cms to the bodice length. In truth I probably could have added more than that because I feel there isn’t as much blousing at the waist as there seems to be in the photo in the book [If you know, or suspect, you have a long body length then pay close attention to this before cutting your fabric, get someone to take your nape to waist measurement and compare it to the back pattern piece. If necessary then add any extra through the horizontal ‘lengthen/shorten’ lines, and don’t forget to do the front as well!] If you’re wondering why this matters, it will mean that the waist seam sits too high above your natural waist and could look more like Empire line. 

I followed the instructions in the book to draft my own skirt pattern which was simple enough, you only need one because the front and back are identical (you’ll need a decent sized piece of paper to do this) I cut the new front and back as complete pieces so that I didn’t have to cut anything on the fold, I also wanted a short sleeve so I traced one off. 

The fabric was a little bit curly at the edges so I took my time cutting out, be careful not to pull or drag the fabric at this stage because this could result in twisting of the finished garment. It’s helpful to mark stripes onto the pattern so that you can then match them to corresponding seams more easily. Cutting a single layer of fabric can really help make this more straightforward, and be less wasteful too.

Moving on, the suggestion for the waist casing is to use eyelets or buttonholes. I used a small round-ended buttonhole, whichever method you choose make sure you interface underneath first to stabilise the fabric. I used the quilting guide to help me sew an accurate 2cms seam to create casing. Once I’d sewn it I used a bodkin to thread the ribbon through.

Tiny round-ended buttonholes instead of eyelets
Using the quilting guide to sew an accurate 2cms seam to create the channel
I used a bodkin to thread the ribbon through, this was some tape I used initially until I got the better-matching teal grosgrain ribbon.

The rest of the construction was pretty quick because I already knew the T-shirt in size 5 was a nice fit, the skirt was a bit ‘hippy’ though so I took some off in that area. Following the drafting instructions the pattern piece is shaped for the waist but, for me, a straight rectangle would suffice.

The length was educated guesswork but I’m very happy with it and it’s not too restrictive at the hem, any longer or narrower and the skirt might need a split in it to allow movement. I have the advantage of using a Pfaff coverstitch machine to hem the sleeves and skirt but a twin needle or a zig-zag stitch will do the job too, and don’t forget to use a ballpoint or jersey needle. I used a narrow grosgrain ribbon in a toning teal to slot through the waist casing to complete the dress. As I mentioned near the beginning I might add just a little more length to the bodice next time but otherwise I’m really pleased with this Tabitha dress, it will be comfortable to wear for everyday and easy to roll up in a suitcase if I ever get to go on holiday again!

not keen to reveal pasty white legs!

Minerva provided me with this lovely fabric to write about, I’m delighted with the quality and I’m especially happy with the dress which is so just comfortable.

Until next time, happy sewing

Sue

Fantail Top from The Sewing Revival

Janine at The Sewing Revival, the pattern company based in New Zealand, is gradually creating a growing collection of stylish patterns and there is something very appealing in their deceptive simplicity I think. I’ve made a few versions of several of them now, including the Sidewinder pants, the Bellbird top and the Heron dress.

When Janine kindly offered me my choice of the range to choose from I picked one of the more recent releases, the Fantail top. At first glance it appears to be a simple raglan-sleeved top but along with the high/low hemline and elasticated front hem it offers variations of scooped, ribbing or V neck, elasticated or ribbing cuffs, and the back hem can be finished with ribbing too.

I had a rummage in my stash for some suitable fabric, ideally something with a bit of drape works best so soft viscose, crepe, georgette or chiffon if you fancy a challenge, cotton lawn, wool challis or fine linen would all work very well. Light- or medium- weight jersey will make it into a very chic sweater. I’ve no idea where my piece of navy fabric came from, probably I was given it by an elderly lady because it had a little ticket pinned to one corner saying it was 1 1/2 yards x 54” wide and cost 90p! It certainly smelt a little bit musty so the first thing I did was give it a quick hand-wash, it turns out that the colour ran quite a bit and I was left with blue hands for several hours afterwards!!

The patterns are sold in size bands which each contain 4 sizes (there is some overlap between the brackets) and each band is layered which gives you the option to print only the sizes you want so I printed UK 10 and 12 because, having lost some weight recently, I wasn’t sure which size would be best. In the end I cut a UK12 and it looks fine I think, it’s a roomy style so I could possibly go down a size but as I’m one of life’s ‘fluctuaters’ where weight is concerned maybe I won’t.

I like the instructions on Sewing Revival patterns because they are well explained and illustrated with photographs. If you’re an experienced sewer like me then you won’t necessarily need to follow them closely all the time but I do keep half an eye on them so that I don’t miss a step or construct in the wrong order which might have repercussions later on.

I made the scoop-neck version with elasticated cuffs which is probably the most straightforward variant, the round neck is just the right amount in my view, not too wide, not too deep. Raglan sleeves are super-quick to construct, I usually sew the neck facing on after the shoulder seams and before sewing the under arm seams.

The front and back hems are very different lengths and finished differently so don’t rush through these elements. I ignored the suggested bias-binding finish on the back hem and used one of my favourite techniques of a pin-hem instead ( I wrote instructions for this last year in this blog post on hems )

The USP of this top is the deep partially-elasticated front hem. It looks great but it’s really not difficult to achieve. There are suggested lengths to cut your elastic for each size although you could use a shorter piece over the same length if you want to pull the front in a bit more. Or you could also use a narrower elastic but the pattern is cut for wide width like this so you may have to make an alteration to the hem depth accordingly for the channel to work.

This is the side seam where the two levels come together, make sure the back hem is fully enclosed within the front so there is a nice smooth line from front to back.
The finished top on the stand.
I sewed the deep elastic cuff version, there’s a subtle amount of gathering.

As I said, this is a simple top with eye-catching details, it’s probably a half-day project if you’re got everything you need when you start.

The sun came out so we headed out to the garden for photos. I’m wearing one of the pairs of Sidewinder pants I made in 2019, they are a bit baggy now.
There’s a nice dip to the hem at the back.

I’ve already got some fabric lined up for another Fantail hopefully very soon, a nice piece of soft viscose from Sew Me Something and ribbing given to me by my friend Kate which by sheer good fortune coordinates perfectly! There’s lots of possible variety with the Fantail, short sleeves is another for example. Incidentally, there is also a slightly different sleeveless version of the Fantail available too.

Until next time, Happy sewing

Sue

Box pleat shirt from Trend Patterns

I’ve made loads of different clothes over the decades but actual shirts for myself have not tended to be among them. I’m not sure why, possibly because I had to wear boring school shirts for years and years, and for a while I had to wear a uniform when I worked for the John Lewis Partnership so my personal preference has tended to softer blouse shapes. That said, I love to see a crisp white shirt especially when it’s given an inventive twist. It’s a wardrobe staple and yet there’s always room for a new version. 

Lucy at Trend Patterns has just released the first 3 patterns of what will become a shirt collection and each is available printed, as a PDF or as a complete kit with pattern, fabric and trims. TPCSH1 is a feminine Pussy bow top with shirt sleeves and a ruffle hem, TPCSH3 has stunning gathered ‘angel’ sleeves which really make a statement whilst the body is kept simple and traditional so that the sleeves do all the talking. 

Lucy offered me the kit of TPCSH2 to try out, it is a box-pleated front shirt, deceptively simple to look at but those details take a little time to get right. It’s classified as ‘moderate/hard’ and I would agree, not because the elements in themselves are especially difficult but each of them needs some experience and precision to execute so I wouldn’t recommend this as your first shirt project. 

The kit comes with enough good quality plain white cotton poplin to make up to the largest size of a UK 22, along with Trend-branded buttons (a nice touch) and iron-on interfacing. All you need to provide is your own thread! 

I started off by taking my measurements and comparing them to the sizing chart, there is also a chart giving you finished garment measurements too which is helpful because it will give you some idea of how oversized the shirt will be when it’s finished. I made a UK 12 and as you will see from the finished photos it’s a very generous fit, to be honest, if you want a close-fitting shirt then this particular pattern won’t be the one for you. 

I opted to trace off the pattern, there are two separate fronts, right and left, and a whole back plus sleeves, yoke, cuffs and collar. There is no pattern piece for the bias binding for the sleeve placket, you just need to cut yourself two bias strips approximately 30cms x 4cms. The right and left fronts are the same except for the extra on the centre front which creates the folded fly with concealed buttonholes. I traced off one front then, to save some time and to ensure they were identical, pinned it to more spot and cross paper before cutting them out together so that I had a mirror version with the additional front added. It’s really important to trace the front very carefully because of the three box pleats, if they are each a bit off you risk the pleats not sewing together accurately which will leave you scratching your head. There are a lot of drill holes to mark the stitching which will eventually hold the pleats in place, don’t be tempted to miss any out because they are also really helpful when you’re folding and pressing the pleats in position. You could choose to trace just half the back to save paper if you intend to always cut it on the fold anyway but having a whole piece gives you the option to have the fabric out flat, besides, it’s almost always more economical to cut fabric out as a single layer [this can be especially helpful if you ever need to do some tricky pattern placement or matching]

Because the fabric is plain, placing the pattern pieces and cutting out was a breeze-no pattern matching, yay! I spent quite a while making traditional tailor’s tacks for every single one of the drill holes. You could use a washable or some other kind of disappearing marker pen if you are confident that it definitely won’t come back to haunt you but I wasn’t going to take the risk on plain white fabric! 

In the past I’ve occasionally found some of the earlier Trend instructions a bit tricky to follow but the more recent ones have illustrations rather than photos and I found this set very clear. My biggest piece of advice would be to read then re-read the instructions before you start, and to highlight anything that you know you’re going to have to really concentrate on, this isn’t a race after all. 

Constructing the fly front and button stand first, including the buttonholes, was satisfying, I often feel like I’ve run out of steam by the end of any project which requires buttonholes and it’s a bit of a chore by then but this gets it out of the way nice and early. [I should add at this point that I started out sewing with a fine size 60 needle so as not to leave too many noticeable puncture holes in the plain fabric if I went wrong or needed to unpick. However, this size needle kept skipping stitches for some reason so I went up to a 70 and had no further problems]

transfer all markings and instructions to the paper pattern if you’re tracing it off. I made tailor’s tacks through every drill hole

My second piece of advice would be to press your pleats on the ironing board if you possibly can. I only have a small heat-resistant board in Threadquarters which meant I was constantly moving the fabric which was not ideal, it was so much easier on the ironing board because the whole piece fitted on. Do not rush this part, with pure cotton fabric you can have the iron on pretty hot but do be careful of your fingers with hot steam. Pin, tack or Wonder Tape the pleats in position once pressed if you want to. 

pressing the pleats on the ironing board, the snips top and bottom along with the tailor’s tacks will help you get each one in exactly the right place.
In progress-making the bar tacks

The instructions are to stitch down each pleat according to the markings using a few stitches. I did quite a lot of testing using a variety of decorative stitches for this before I committed to the bar tack. The next challenge was getting each of those bar tacks (30 in total!) central over the pleat. My machine comes with a number of feet which are used in conjunction with the decorative stitches and one of these has horizontal red lines which proved very helpful in getting lined up for every bar tack. After making a few of these bar tacks I ‘got my eye in’ so I could tell very quickly where to start each stitch, having the needle stopping in the up or down position is an absolute essential feature on my machine for me and it was brilliant during this, being able to lift the foot to check I was sewing in the correct place without the work shifting was so helpful. The photos will hopefully make my method clearer to follow. It’s vital to take your time and be as accurate as possible during this stage because the box-pleats are the USP of this shirt and it will obvious if they are off-kilter. I sewed in white thread but you could use a colour, or even hand embroider to give your shirt a totally original look.

testing various stitches including triple straight stitch and arrow heads, the difficulty was going to getting every single one central over the pleat

Incidentally, Trend will be creating a series of video tutorials to help so I suggest you check their Instagram account or the website for those. Also, there was a slight problem with pattern markings for the back box pleat which were incorrect. This has been rectified but if you bought a copy very soon after release you might find you have to scratch your head a little, the notches were in the wrong places. Check the website if you’re in any doubt.

the right front, including the fly, taking shape
the shirt with the side seams now sewn up, ready for the sleeves to go in
sewing the continuous binding to the sleeve opening. the instructions don’t call for it but I like to sew across the top of it at a 45 degree angle to encourage the binding to stay on the inside
close up of the finished front
all done
close up of the finished bar tacks

I followed the order of construction to complete the shirt (I usually do the first time I make a pattern) but personally I would put the collar on after making the yoke. I like to do it before the side seams are sewn up or the sleeves are inserted, unless there’s a technical reason not to obviously. 

the finished back yoke
I popped a bar tack in the middle of the back to hold the pleat in place, this hadn’t had a proper press yet

Everything came together really well, I’ve always found Trend patterns are accurately drafted so I know the pieces will go together well without major discrepancies-this is why it’s so important to trace off carefully if it’s your preferred method, if seams or notches don’t match up you won’t know where the fault lies [the same applies to accurate cutting out too] 

The sun came out so we could take some outdoor photos, I’ve paired the shirt with my much-worn Megan Nielsen Ash jeans
is it a bird? is it as plane?…
I’ve pressed the pleat now

Clearly not everyone will want to make a shirt that is going to take a sizeable amount of time to construct, or to launder afterwards for that matter, but if we only made simple loungewear for ever then the art and skill of making our own clothes will be lost, just at a time when so many people have discovered, or rediscovered, the joy of sewing for themselves. There will always be a place for a classic white shirt and Trend has created a small but growing collection with original twists on the genre. The last year has been so tough for small business owners so I really appreciate being given this kit to try out, I wasn’t under any obligation to review it other than share some photos but personally I have no problem with sewing and writing about it. I will always try to give you a balanced view and if I can support a little business by giving them some positive exposure then I will. Alongside that I’m keen to demonstrate that a design-led style doesn’t have to beyond us ‘ordinary’ sewers either, if you like it then sew it! 

I hope I’ve given you some idea of what will be involved in making the TPCSH2, if you’re looking to push your skills on a bit this could be a good project. Maybe you need/want a plain white shirt in your wardrobe [amazingly I didn’t have one in mine, just a couple of short-sleeved ones] I might layer this with a sleeveless tank top over it, or a waistcoat could look interesting. This is a typical cotton poplin shirting but you could use a variety of fabrics, you could have fun with graphic prints or stripes, try something soft like double gauze or a crisp linen? Or what about harvesting the fabric from several well-worn mens shirts to make a more patchwork look. Take your time though and enjoy the process.

I’ve got a long-sleeved T-shirt under it because it was a chilly day and it will be perfect for the day I can return to the V&A. I don’t know about you but I’ve really missed putting an outfit together to go on a nice day out, deciding which of the lovely garments I’ve made that I want to wear and how I’m going to accessorise them. It seems such a small silly thing to miss but I shall be so glad when I can start doing it again.

Most of all, thank you to Trend for giving me the opportunity to try the kit, until next time,

Happy Sewing

Sue

a new Lamazi blog, sewing menswear!

It’s a new year (apparently?) so it’s time for my next Lamazi blog and I’m sewing something for Mr Y! I don’t know about you but I’ve felt I needed to work on something a little different to most of my other recent makes, I’ve made myself some lovely garments that I’m now frustrated not to be able to wear much as I want but Tony has been in need of some new clothes for a while now so it’s his turn to be on the receiving end! 

I don’t know what you think but I’ve found that men’s wear patterns and suitable fabrics are definitely a bit harder to come by than women’s or children’s, they are out there if you’re prepared to look but it’s not easy. I’ve made him some nice shirts in the past which you can read about here, and I had made him a couple of Thread Theory Finlayson sweatshirts recently and then my good friend Claire told me about their Carmanah top which was quite a new pattern. It has several options so you can individualise it, for example with full length or quarter zip, hood or collar, and with or without kangaroo pockets. 

Lamazi offers a range of co-ordinating See You at Six fabrics with plain and patterned French terry, and ribbing, all dyed to be a perfect match so we chose the ‘Clouds’ design in Bistro Green. 

I’ve never purchased ribbing fabric before so I was unsure how much to buy, initially I requested far too much because the pattern instructions made no sense to me. Liana at Lamazi and fellow-blogger Sharlene advised me so I had 1metre in the end to be on the safe side and that was sufficient for an adult garment. If you find yourself in a similar situation I suggest you measure the appropriate pattern pieces to get an idea, or try contacting the fabric seller and I’m sure they would be happy to advise. For an adult garment it almost certainly needs joins whilst something for a child probably wouldn’t.

Based on T’s measurements (he’s 6’3” and, although he’s lost about 28lbs during lockdown, he’s not skinny) I cut him a size large but I added about 2cms at the CF and CB folds at the bottom because the previous version was just a little snug at that point. He likes the body length which comes down to about hip level, and the sleeves are nice and long too so I didn’t need to add any length to them. 

The making up instructions and diagrams are quite clear, I got into a bit of a pickle using the twill tape neatening method though, partly because I printed off the booklet a bit small so I couldn’t easily read the instructions(!) and partly because the green twill tape I had managed to buy was wider than required! Anyway, I persevered and it looks OK in the end. This tape method wasn’t essential and overlocking is perfectly satisfactory, I just thought I would try it for a nice finish on the inside, it definitely adds more complexity if you want to up-skill though. The collar version has a nice detail of the chin guard over the zip which is worth adding for a quality finish.

I put the twill tape on the wrong piece of collar initially! This is the outer collar and the tape should have been sewn to the inner collar. Incidentally, I added iron-on interfacing to the top collar to give it a little more body. It doesn’t call for it in the instructions but I felt the first version could have done with a bit more structure. Have a look at the photo below to see what I mean.
This first version was made with cable knit bought from 1st for Fabrics I think the collar is collapsing a bit although it’s not really a problem
I added twill tape to neaten the front edges before inserting the zip
I tacked the zip into the opening before topstitching in place.
second attempt at the tape trim! the tacking you can see is holding the fold at the top of the collar in the correct place until I’m ready to top stitch it later on.
The tape I bought was too wide so I sewed it on higher than the instructions and then trimmed away the excess in order to turn it up and sink stitch from the right side.
The finished collar from the inside. The green is a very difficult colour to photograph and the zip and tape are a slightly better match than they appear here. I bought both of those from Frumble Fabrics, they have a wide selection of all sorts of haberdashery that I haven’t seen elsewhere.
I finish overlocking by putting the threads on a large-eyed tapestry needle and slot it back through the stitching for a couple of centimetres like this which keeps it secure and tidy.

This fabric is quite pricey but, in my opinion, it’s really lovely quality and it sewed together beautifully. There’s just enough stretch and it would be a good weight for sweatpants or a sweater dress too if you’re tempted. This is the first time I’ve used a range of co-ordinating fabrics and the finished result is really pleasing. Equally you could mix and match colours or prints using remnants for this pattern too, because of the way it’s cut in segments, especially if you go for the full zip version. 

T has gallantly modelled the finished result-he’s delighted with it-he’s usually my slightly impatient photographer so the boot was on the other foot today!

Have you sewn anything for the men or boys in your life? How do they feel about it? Luckily T isn’t very demanding where his threads are concerned and he’s always been very happy with the items I’ve made him so far…..I haven’t attempted trousers in years though so perhaps that will be next? I’d interested in which patterns or fabrics for men you have been able to source, I think it’s an area for improvement in sewing terms.

Until next time, happy sewing

Sue

The Sewing Revival Heron dress hack

Two years ago I wrote a review of the Sewing Revival Heron dress which you can still read here. I liked the pattern so much that since then I’ve made another knee-length version in a viscose/linen mix fabric from Ditto in Brighton and a blouse variation too in a beautiful soft Italian cotton voile, also from Ditto. I wore it often although not so much lately…

wearing the blouse on my trip to Paris for the Sewcial in May 2019
my very first version of the Heron dress…it has pockets!

While I was at Sew Brum in October 2019 I bought some lovely soft brushed printed viscose twill from Barry’s Fabrics with the express intention of making another Heron but this time making it longer and more cold weather-friendly. There had been a lot of Wilder Gowns by the Friday Pattern Company popping up everywhere at the time, I liked the tiered style a lot but I knew I could create my own take on it by using a pattern I already had. A multiple-layered skirt like this isn’t difficult, it’s really a case of working out the number and sizes of rectangles you want to use. If you take a look at this post I wrote about recreating a sun dress for a client in 2019 you’ll get the gist. Because I like the top section of the Heron so much I decided this was a good pattern to use and it wouldn’t be difficult to adapt it to what I wanted.

All the quantities and proportions I have used for this dress were completely arbitrary and had to be based primarily on the quantity of fabric I’d purchased [which I can’t actually remember as it’s well over a year ago, probably 3m of 150cm wide fabric I’d guess] and my own height of 5’5” so bear this in mind if you decide to have a go yourself. I wanted the dress to be nice and long so eventually I settled on approximately hip length for the bodice, the finished length of the side seam is now 40cms. I folded the front and back dress pattern sections up out of the way when I pinned them to the fabric (obviously you could trace or print off a new copy of the PDF if you wish) Once both bodices, sleeve and pocket pieces are on the fabric [pockets could be cut from something else if you’re a bit short of fabric] I could see exactly how much I had left to create the skirt from. I kept it very simple and divided the remaining fabric into two equal rectangles across the full width, each one measured approximately 56cms long but that had to include the seam allowance at the top and a hem at the bottom.

Initially the construction of the dress followed the normal method up as far as putting the pockets into the side seams of the bodice as per the pattern.

Making the skirt was very straightforward, I joined the short selvedges to one another [if it’s a one-way design make sure the print is running the same way on both pieces] to form a large cylinder of fabric with two side seams. Press the side seams open, if you’ve been able to use the original selvedges they might not need finishing. I made the hem at this point too, it seemed easier than wrestling with a complete dress at the end, although this could have backfired on me if I hadn’t been happy with the length but I was pretty certain it would be OK.

I ran two rows of gathering stitches within the seam allowance of the top edge, I pinned them in position matching the side seams, centre front and centre back, plus the quarter seam positions too. Gather up carefully so as not to break the threads, small pleats would also work here especially if the fabric would be bulky otherwise, it depends a bit on the weight of the fabric to some extent. Once I was happy with the gathering distribution I sewed the skirt on and overlocked the seam.

And that was it. Now, I have to say that because I was taking a risk with proportions and limited by the quantity of fabric I’d bought that if I were to repeat this I would definitely make the bodice quite a lot shorter and make the skirt from more than one gathered tier instead. I’m happy with the overall finished length but I think the seam at the hip isn’t quite right. But, by wearing it with a narrow leather belt (there wasn’t any fabric left for a self-belt anyway) and bringing it in at the waist I’ve saved it, the belt gives it a lot more definition.

I added a tie at the neck this time using a bit of grosgrain ribbon which I had knocking about.

I grabbed a cheeky selfie in John Lewis with my sewing friend Ruth in the autumn, we can only dream of when we can meet up again at the moment though sadly. that’s my upcycled jeans jacket I’m wearing

The dress was finished around a year ago and these photos were shot in the autumn but it’s taken until now to write up. I just wanted to demonstrate how easy it can be to make your own version of popular patterns using one you already have-there’s a certain risk involved because it might not be completely successful but that’s always the risk anyway when making our own clothes-a style might turn out not to suit us after all, or we make a wrong fabric choice, or it could be a triumph so why not revisit what you already own before buying another pattern?

Until next time, happy sewing

Sue

Trend Utility trousers TPC12

My first blog of 2021 features my last make of 2020. After several quiet weeks where I didn’t sew any garments, I had cut this project out a couple of months back but then hadn’t felt motivated to make them at the time…the days between Christmas and New Year was the right time to get my head around a nice involved project though. There has been so much going on in the UK recently, (understatement!) especially in these last few weeks, that I wanted something I had to concentrate on to take my mind off other events outside of my control.

If you’ve read my blog in the past you’ll know by now that I’m a big fan of Trend Patterns but these are the first trouser pattern of theirs that I’ve tried.

I saw Lucy wearing her own version of TPC12 on her stand at the Stitch Festival in London back in early March 2020 (just before everything went weird) and it was the unusual split hem detail that initially I really liked. On closer inspection there are some other nice features too, like the topstitched front seams with optional faux pocket flap, and a button fly. These are the kind of details that attract me to a pattern but I would say before I go much further that this is definitely an intermediate pattern as a result, you will need to be a confident sewer or at the very least game to increase and expand the skills you have already. Before I left the show that day I bought some nice heavier weight plain black linen from Rosenberg’s to make them with.

It was then literally months before I decided to tackle the pattern though. I’m not going to lie, and don’t judge me either, but I had piled on weight during lockdown which I wasn’t happy about and as I got bigger the last thing I wanted to do was make a pair of trousers that emphasised that fact. Eventually however I began dealing with the weight issue which in turn encouraged me to revisit the Utility trousers in the early autumn.

Instead of using the linen for the first pair I bought some grey stretch cotton twill from Backstitch near Cambridge. It’s lovely fabric for trousers and a very good quality at a reasonable price. Because the Utility’s are a fixed waistband I went by my waist measurement at that time (it was shrinking!) so I chose the UK 16 and I could tell that the hip would on the big side but that was OK.

I patiently traced off all the pieces which took a while because there are quite a number of unique pattern pieces that need to be cut right side up (RSU) Labelling them all is of paramount importance so that you don’t end up with unusable pieces of fabric cut the wrong way. Once I had cut the fabric out I left all the pattern pieces attached to the fabric until I had either interfaced them or until they were ready to be sewn. I made both my versions exactly (apart from fit alterations) as the pattern but you could leave off the pocket flap detail by cutting a pair of side fronts, or you could have two pocket flaps by doubling up those pieces instead. An advantage of having so many single pattern pieces is that you might have a more economical layplan because they will interlock better, folded fabric is a much less efficient way of cutting out, a single layer just takes a bit longer.

I said at the start that this is an intermediate pattern in my opinion and that is largely because the hem vents and the button fly are quite involved, although not actually difficult, plus I found the instructions and diagrams were a bit tricky to follow. I didn’t go wrong but they do require absolute concentration. What I’ll do in this blog, so that’s useful to you if you decide to make the trousers, is simplify the order of making down to a basic list which you can use in conjunction with the actual instruction booklet. I won’t give you specific, press here, topstitch there, instructions though, they are in the booklet and the diagrams are very detailed.

My first piece of advice, after you’ve attached all the interfacing to the relevant pieces and transferred all markings to the fabric, is to overlock all the cut edges (except the waist and fly front) first. I don’t normally do this because I prefer to overlock as I go along but it makes more sense here to do it as a batch process, just make sure you don’t trim away too much or lose your notches in the process.

Start by making the ‘pocket’ flap [make up the optional pocket bag if you are going to have one but set it aside for the moment] also, make the back darts and set the pieces aside for now.

Join the front seams for both fronts as far as the vent markers, do not join the fronts to the backs just yet. I found it easier to have only the vent sections to work on flat first although the instructions tell you to join the fronts to the backs. Once you’ve made both the vents except for the final single topstitching to hold the flap in place and are ready to turn up the hem join the fronts and backs at the side seams first. Now complete the topstitching to hold the vent in place then join the inseams, turn up the hem and topstitch to finish. [If you’re using the additional pocket bag I would add it whilst the leg is still open and flat, before sewing up the inseam. I sewed mine on earlier and it got in the way a bit when I was joining the various leg seams]

Pin and partially stitch the crotch seam as per the instructions then apply the outer waistband and press the seam up towards the waistband. [If you want to include belt carriers I would add them before attaching this waistband so that they are caught in the waist seam, the tops of the carriers will be enclosed when you add the facing]

Next, make the right fly section and buttonholes as per the instructions and diagrams. I’ve included a photo of where I stitched through the layers of the right front to hold them all together, I’m not sure if this is quite what is intended but it works-I couldn’t make sense of it otherwise!

the pencil is pointing to where I’ve added the row of stitching to keep the layers together.

Make the left fly front and attach the waist band facing, I’ve included the photo below of how this should look from the inside (yes I did use jazzy overlocking thread just because…)

the completed grey version showing the button fly and jigger button

Sew the remainder of the crotch seam to complete it, then sew the entire crotch seam again about 1-2mm away from the first stitching line.

Sink stitching-to complete the waistband-is simply the industry term for ‘stitch in the ditch’.

Obviously there are points where you would be advised to try the trousers on to check the fit as you go so you could do this by pinning on the stitching line (parallel, not at a right angle!) to avoid unpicking. The advantage of having a split waistband on the centre back seam (like good quality men’s trousers) is that you can fit into the small of the back more effectively.

So that’s, hopefully, a simplified method for you, it isn’t that I think the instructions aren’t good, it’s just that I got a bit confused between what was written and which diagram to follow, and that’s why I wrote it down in a clarified form as I made the second pair.

The fit of the first pair is technically not that good but they are soooo comfortable. The waist was a good fit initially although I’ve lost more weight since then so it’s very roomy now. The major issue (and I’ve read this in a few reviews) is that the crotch length is very long and looks quite droopy. You can see this in the photos of my grey pair, and this makes the cropped leg length look a bit too long as a result. For the second pair in the black linen I redrew the pattern down one size and also folded out 3cms horizontally at hip level on every pattern piece to reduce the rise. The second pair are a much better fit but that won’t stop me wearing the grey pair, it doesn’t particularly bother me that they are overly generous because the shaped waistband can’t fall off my hips anyway. Yes the grey pair are very baggy but that’s fine.

The black linen pair are a better fit at the waist, there’s still plenty of room (too much room?) over the thighs but I don’t mind that. Maybe I’ll shave a little off the next pair, or maybe I won’t…

Overall I’m a big fan of the Utility trousers and I’ll probably make more, now that I’m getting better with the fit. The design details are worth the effort but it is a project you’ll want to take some time over, I had to turn off the radio so that I could concentrate completely and I read aloud each instruction several times to ensure I was going the right way. I sewed matching topstitching but you could use a contrast thread, or maybe you could line the waistband and button stand with contrast fabrics? Apart from the pocket bag if you add one there are no other pockets so you could add some in the side seams quite easily I would have thought, or patch pockets on the back perhaps? I quite fancy a pair made in chunky cord too…

I hope you find this useful, or I’m happy to try and help if I can.

Until next time, happy sewing

Sue