Sewing the M&M Ellsworth shirt for Backstitch

The Backstitch store at Burwash Manor near Cambridge.

As one of the new team of Backstitch Ambassadors I relished the chance to go along to the gorgeous shop at Burwash Manor to browse their fabrics and patterns. It’s about 40 minutes from where I live and I love to go there whenever I get an opportunity, I’ve previously included it in this round-up of Hertfordshire based fabric shops. To be completely honest, I already had an idea that I would like to make the newish Merchant and Mills Ellsworth shirt but I had an open mind about fabric choice. In my head I was looking for a lightweight linen-type but as soon as my eyes alighted on the checked double gauze I was all in for that! It was folded on the bolt with the large check visible on the outside but when I discovered the reverse was small checks my mind was blown and I knew I could mix the two sides to create a unique garment. There are currently 4 colours available but I settled on the pretty shell pink variation. I took 2 metres as per the pattern instructions but after cutting it out (and as I’ve found before with M&M patterns) I had almost 50cms left over, even allowing for pattern matching. It’s very annoying when this happens and I’ve made a note for next time. I cut a straight UK 12 with no mods.

I loved the elliptical pearly buttons but there were only two of the pink shade left so I made do with two pink and four ivory. Backstitch have quite a wide selection of buttons, trims, and ribbons plus lots of other haberdashery and sewing equipment including Brother sewing machines.

The Ellsworth is quite typical of M&M’s aesthetic, it is a very wide and loose fit shirt with a stepped hem, a collar and button placket and cropped, cuffed sleeves. It will lend itself towards fabrics which have an element of fluidity and drape such as soft linen or cotton-types, light woollens, crepe, chambray or babycord. Some light- or medium-weight jerseys would probably be okay but I wouldn’t recommend ones with a lot of stretch. 

Another reason for choosing this shirt (apart from the fact I liked it anyway) is because I had seen a few makers on Instagram were having trouble interpreting the instructions for the placket. I hope what follows will give you a bit more information and guidance. 

Away we go…

Definitely give your fabric a wash first, its light loose weave will shrink a little (it will be very crinkly when it comes out of the machine but don’t panic, it will press flat again. You may ultimately prefer the crinkles but they will be hard to work with during the making process so press as you go for now)

If you are a person with no patience when it comes to laying up your fabric, or time is tight, then this may not be the fabric choice for you because it does need some careful laying up and folding to get the checks straight and matching [or you could cut every piece on the flat to save on the head scratching] There were a couple of places where, in spite of my best efforts I was bit off but I won’t tell you where they were and you might not notice anyway! It does have the advantage of the large check being 3cms square and the reverse is 1cm squares so a 1cm or 1.5cm seam allowance shouldn’t be a problem to follow.

The problematic placket is made first so here’s my interpretation of the instructions for you. Begin by interfacing all pieces as instructed (although I interfaced the whole placket rather than half as the fabric is quite fine and a bit unstable)

Mark the bottom of where the placket will be sewn on with tailor’s tacks or a soluble marker pen then stay stitch just within the seam allowance, at 1.4cm (14mm) to reinforce the area. For visual reference, the large squares are my right side, the small squares are the wrong side of the fabric.

Cut down the centre front line and carefully snip diagonally into the corners.

Fold and press each of the two placket pieces down the centre and then press in the seam allowance on one edge only. Trim this by half

Next, pin each unpressed edge onto either side of the slit, right sides together.

Stitch each side in position down as far as the tailor’s tacks, you should stop a little bit short of the bottom edge.

Trim down the seams by half.

Now flip the work over so that you have the wrong side uppermost. Press the seams in towards the placket piece on the left as you look at it then fold over like this, pin and tack in place. Now turn the work back over again.

Working with the right side uppermost, edgestitch the placket you have prepared.

Keeping the right unfinished placket out of the way, you need to position the left placket (the one you have just sewn) layered like so with the triangle at the base of the slit. Carefully stitch just below the original staystitching. This is with the inside of the work uppermost, neaten the edge and press downwards.

Now work on the right placket (it is on the left as you look at it though) Fold up the lower edge as demonstrated here, pin and tack in place. Edgestitch on the right side of the placket only as far as the bottom, do not sew across the bottom yet. Now work your buttonholes while the placket is still separate.

After working the buttonholes, lap the placket over the underneath one and stitch it in position like this.

You should now have a placket which looks something like this.

Next I moved on to the sleeve opening which is neatened with a very narrow bias strip.

I found the bias strip included to be incredibly narrow, especially for a fabric which is loose weave and a bit prone to fraying so you may want to cut your strips a little bit wider. I made the strips work but they were very fiddly. Instead of edgestitching as per the instructions I sewed them with a tiny zigzag which I hope will hold them firmly in place. Or you could slipstitch them by hand if you prefer. Next, fold the bias evenly in half and stitch across the top at a 45 degree angle, I’m not sure if the diagram intends you to sew through the sleeve too, I didn’t.

The way I’ve sewn it, once it’s finished, the sleeve opening and cuff looks like this.

The hem facings are sewn on next, then join the shoulders using French seams. This is a useful technique if your fabric is very fine, sheer, or frays badly, or if you don’t own an overlocker. Obviously you can sew a flat seam and overlock/zigzag if you prefer. You could also topstitch these seams if you want a bit of interest on them. My personal preference is to press shoulder seams to the front, this is so that the seam is slightly less visible when looking at it.

I found the collar instructions straightforward so I won’t go into them as well, I opted to catch the lower edge down by hand so that I had control over it and a really neat finish. I also added a label from Little Rosy Cheeks.

Inside the finished collar

The sides are then French seamed, be careful with the step at the lower edge and make sure you don’t take too much seam allowance on the seams because this could throw out the overlap at the top of the opening. I used the bartack stitch on my Pfaff to secure it as this could be a point of weakness further down the line.

I opted to sew two rows of edgestitching along the top of the hem facings, just to add a bit of interest.

Finally, the cuffs are sewn on and the buttons added.

all finished

I’m all in Merchant and Mills today, these are their Eve trousers in cream drill which I bought at their Rye store back in September 2021.

I cut a straight UK 12 with no modifications and I’m 5’5” tall but if you’re taller you might want to lengthen the shirt as it’s quite cropped at the front.

I’m very pleased with how the Ellsworth has come out, I’ve worn it with flat-front Eve trousers but it will look good with a skirt or even a dress under it for layering. I’m going to have a look through the stash to see what other fabrics I can make it in now!

I’m delighted to have the opportunity to write for Backstitch because it’s a lovely little shop which I’ve been visiting for a few years now. It’s in a beautiful rural location and sells a really nice, well-considered range of quality fabrics and indie patterns and sewing books. As Ambassadors we are provided with gift vouchers to shop in the store, it’s entirely up to us what we make and how much of those vouchers we spend, the balance can be kept to spend on another occasion if we choose to. If you don’t live anywhere near enough to pay a visit yourself then Backstitch has a recently revamped website to shop through too, their range of yarn, knitting and crochet patterns are all on there too.

I hope you have found my review useful, that’s always my intention, do write in the comments if there’s something which still isn’t clear and I’ll try to help.

Until next time, happy sewing

Sue

Simple Sew Palazzo Pants updated

In 2019 I decided to try something different to dresses from the Simple Sew pattern collection for my blog post so I chose the wide-legged Palazzo pants. 

I always have a look at any posts or reviews about a particular Simple Sew pattern first to check if there are any pitfalls I should look out for which might influence my decision, or how I tackle making it, and the overall opinion of trousers was positive. I sorted out some fabric from deep in the stash, it’s a viscose from the now-defunct Adam Ross fabrics which has a good drapey quality, although I know it will crease so I’ll wear these permanently standing up! 

There are only 4 pattern pieces to the trousers-front/back/waistband/pocket- which makes them very simple to lay up and cut out, you could even leave out the pockets if you’re short on fabric but why would you leave out pockets?! 

I checked my measurements against the chart to decide my size, I also measured the pattern pieces to get some idea of the ease involved but I was optimistic they would be generally OK. If you’re very unsure, or between sizes, I’d suggest you make a toile that’s about mid-thigh in length to check the fit and comfort around your waist, hips and body length. Leave out the pockets at this stage, there are darts in the back and the front is flat, you could insert a zip in the back if it makes things easier to fit yourself but I didn’t bother. Always sew a toile as accurately as you would the garment itself because if you don’t bother cutting properly or following the seam allowances how will you know where the problems lie? That’s the whole point of a toile! Make any adjustments on the toile and transfer the changes to the pattern pieces. There are no lengthening/shortening lines marked on the midriff area of the pattern so I suggest, if you need to make either of these changes, drawing a line at a right angle to the grainline at a point midway between the waist and crotch level. Fold out or add in length through this line. There is a lengthening/shortening line for the leg length however.

It wouldn’t be a Simple Sew pattern if there weren’t some errors or anomalies to keep you on your toes and this is no different. On the back piece the pocket placement notches are only printed on size 8 and none of the others. Either transfer the markings to your size or remember to snip them when you’re cutting out the back.  

The notches don’t feature on all the size lines so transfer them across as required.

The lay plan for cutting out shows the main pieces interlocking, which is fine if you have plain or multi-directional fabric but don’t forget to keep the pieces running the same way if you have a distinct one-way print. Also, I didn’t cut out the waistband until I was happy with the fit of my trousers as it’s very shaped piece and if it’s too big or too small you’ll probably need to cut another. Don’t forget to make a snip for the centre point on the waistband, it could have done with a notch for the side seam position though as there isn’t one so it’s a bit of guesswork.

I’m not normally an advocate of overlocking the edges until they’re sewn up [because if you aren’t careful you can easily lose too much seam allowance in the trimming and when you join pieces together you could start to make the garment too small, plus your notches disappear] but, as many of the pieces here require the seams pressed open and flat, I overlocked most pieces first this time. 

You will find that for instructions 4 and 6 the words don’t match the diagrams but the drawings are correct 

Next the pockets go in (unless you wish to check the waist/hip fit first in which case tack or machine baste the side seams and leave the back open where the zip will be inserted in order to try the trousers on) The description for the pocket insertion is a bit vague, I’ve made a second pair since writing this piece originally and found it quite unsatisfactory which is why I have updated my advice.

Neaten the lower edge of the pocket bags first then pin to the trouser fronts matching the ‘opening’ notches. Next stitch in place from the waist to the bottom edge of the pocket bag using a 12mm seam allowance (see my notes on the photo above) Repeat with the trouser backs, then neaten the seam edges all the way down enclosing the pocket edges too. On the front only, understitch the pocket opening. Now you can pin the fronts to the backs and sew the side seams shut using a 1.5cms seam allowance, not forgetting to leave the pocket opening unstitched! Finally, carefully sew the bottom edge of each pocket bag closed otherwise your sweets will fall out inside your trouser leg!

After I’d assessed the waist size (comfortable to loose) and crotch length (comfortable) at this point I cut and interfaced the corresponding waistband [for some reason there were two waistbands printed out but I could find no discernible difference between them so just ignore one and cut a pair in fabric plus one interfacing] 

The reason the waistband goes on before the zip insertion is because the zip runs right up into the waistband to finish at the top, there’s no overlap allowed with button or hooks and eyes. You could use the overlap method if you prefer but you’ll need to add some extra length to the waistband on one end to allow for the overlap. 

The lack of indication of the side seams on the waistband means you’ll need to pin carefully to evenly absorb any fullness of the trousers to ensure a good smooth fit to the waistband. [the side seam is probably at the halfway point but not necessarily, especially if you’ve made any fit adjustments to the waist] 

With the benefit of hindsight I would make the waistband in two pieces, a front and two backs with the join at the side seam. This is for two reasons, first, it will allow you to make adjustments for fit more easily and, secondly, I’ve found the centre back has become slightly pointy and misshapen both times I’ve made these now. I believe this could be because the length and curve of the waistband means that it the centre back is very off grain, usually the centre back seam would be cut on the straight grain which gives it stability.

The instructions and illustrations for inserting the zip are reasonably clear however there seems to be a contradiction with an earlier instruction which tells you to sew up the back crotch seam. Illustrations 13-15 appear to have the CB seam unsewn and 16 tells you to sew it up after inserting the zip but previous diagram 6 tells you to sew it up! No wonder I got in a muddle!! My suggestion would be, if you’re using an invisible zip as suggested, leave the CB seam unsewn AND ignore instruction 11 to sew up the inseam until after you’ve inserted the zip. Alternatively, use your preferred method of inserting an invisible zip. Before sewing the waistband down I added two hanging tapes to each side seam so that I had an additional means to hang the trousers up if needs be.

On my second pair I’ve added a small button and loop inside the waistband because I found the zip a bit of a faff to do up without anything at the top of it.

you can also see here how the waistband rises to a slight point on each side in spite of it being fully interfaced. It isn’t the end of the world but I’m a bit cross it’s happened a second time, CBA to fiddle with it too much though…

Hopefully you’ve now arrived at a finished pair of trousers which simply need hemming. After checking the length wearing shoes (they come up pretty long) you could use the simple rolled hem finish as per the instructions or, as I did, leave a sizeable hem of about 5cms to give weight to the very flared leg width. I overlocked the edges to neaten and then used my blindhem stitch with the appropriate foot on the machine to finish [incidentally the photo is of a different project] I don’t use this technique often but it’s a good, and quick, finish on hems that don’t have too much, if any, curve. You could also slip hem by hand of course. 

Different project but still blind-hemming set up

The Palazzo pants are worth persevering with as they have a pleasing smooth fit over the waist and hips which is very comfortable and the leg is wide without being crazy-big. You could shorten them to culotte length very easily, they would work well in a variety of fabrics including linen, chambray or crepe, fabrics with a bit of drape and fluidity will look nicest as you don’t want to look like Coco the Clown!

I’ve made my second pair from a remnant of printed linen/viscose mix I bought from Lamazi recently.

I’m wearing them here with a top made from broderie anglaise that I found in a whole collection of fabric I was given by a friend. Her mother had been a wonderful dressmaker and I found the fabric pre-cut as this simple top which so I just sewed it up.

I’m wearing them here with one of my trusty Camber Set tops from Merchant & Mills

Same Camber, different trousers!

I cut this pair slightly shorter overall so that they aren’t so long if I wear them with flat shoes.

Overall I’m pleased with these trousers, they are a good fit and make a nice alternative to a skirt or close fitting trousers especially in warm weather.

I noticed that this particular post gets a huge amount of traffic so I hope this update clarifies any issues you might have had with the pattern. In fairness, it might have been updated and corrected since my copy was produced in which case you may be able to disregard some/all of what I’ve written!

Until next time, happy sewing

Sue

My latest Minerva make-Tilly’s Tabitha T-shirt dress

I seem to be constantly attracted to teal/turquoise/duck egg shades recently so this Art Gallery organic cotton jersey for my recent Minerva post looked perfect when it hoved into my field of vision! 

I’ve used Art Gallery knit fabrics in the past and the designs and fabric, whilst fairly pricey, are lovely quality. This particular jersey is an organic cotton (with a little Elastane) and very soft, a lighter weight than many so it would be good for children’s and babies clothing as well as adults. I love the print, I think it’s a vaguely ‘Tribal-esque’ graphic stripe and I quickly decided to make a Tabitha T-shirt from Tilly and the Buttons book ‘Make it Simple’ which I’ve made a few times before but to try out the dress hack version for a change this time. 

• 

• 

I traced off a new copy of the pattern using the horizontal lines indicated across the bodice specifically for the dress. I’m not long in the body but I thought it looked a little short so I added an extra 2cms to the bodice length. In truth I probably could have added more than that because I feel there isn’t as much blousing at the waist as there seems to be in the photo in the book [If you know, or suspect, you have a long body length then pay close attention to this before cutting your fabric, get someone to take your nape to waist measurement and compare it to the back pattern piece. If necessary then add any extra through the horizontal ‘lengthen/shorten’ lines, and don’t forget to do the front as well!] If you’re wondering why this matters, it will mean that the waist seam sits too high above your natural waist and could look more like Empire line. 

I followed the instructions in the book to draft my own skirt pattern which was simple enough, you only need one because the front and back are identical (you’ll need a decent sized piece of paper to do this) I cut the new front and back as complete pieces so that I didn’t have to cut anything on the fold, I also wanted a short sleeve so I traced one off. 

The fabric was a little bit curly at the edges so I took my time cutting out, be careful not to pull or drag the fabric at this stage because this could result in twisting of the finished garment. It’s helpful to mark stripes onto the pattern so that you can then match them to corresponding seams more easily. Cutting a single layer of fabric can really help make this more straightforward, and be less wasteful too.

Moving on, the suggestion for the waist casing is to use eyelets or buttonholes. I used a small round-ended buttonhole, whichever method you choose make sure you interface underneath first to stabilise the fabric. I used the quilting guide to help me sew an accurate 2cms seam to create casing. Once I’d sewn it I used a bodkin to thread the ribbon through.

Tiny round-ended buttonholes instead of eyelets

Using the quilting guide to sew an accurate 2cms seam to create the channel

I used a bodkin to thread the ribbon through, this was some tape I used initially until I got the better-matching teal grosgrain ribbon.

• 

• 

The rest of the construction was pretty quick because I already knew the T-shirt in size 5 was a nice fit, the skirt was a bit ‘hippy’ though so I took some off in that area. Following the drafting instructions the pattern piece is shaped for the waist but, for me, a straight rectangle would suffice.

The length was educated guesswork but I’m very happy with it and it’s not too restrictive at the hem, any longer or narrower and the skirt might need a split in it to allow movement. I have the advantage of using a Pfaff coverstitch machine to hem the sleeves and skirt but a twin needle or a zig-zag stitch will do the job too, and don’t forget to use a ballpoint or jersey needle. I used a narrow grosgrain ribbon in a toning teal to slot through the waist casing to complete the dress. As I mentioned near the beginning I might add just a little more length to the bodice next time but otherwise I’m really pleased with this Tabitha dress, it will be comfortable to wear for everyday and easy to roll up in a suitcase if I ever get to go on holiday again!

not keen to reveal pasty white legs!

Minerva provided me with this lovely fabric to write about, I’m delighted with the quality and I’m especially happy with the dress which is so just comfortable.

Until next time, happy sewing

Sue

Box pleat shirt from Trend Patterns

I’ve made loads of different clothes over the decades but actual shirts for myself have not tended to be among them. I’m not sure why, possibly because I had to wear boring school shirts for years and years, and for a while I had to wear a uniform when I worked for the John Lewis Partnership so my personal preference has tended to softer blouse shapes. That said, I love to see a crisp white shirt especially when it’s given an inventive twist. It’s a wardrobe staple and yet there’s always room for a new version. 

Lucy at Trend Patterns has just released the first 3 patterns of what will become a shirt collection and each is available printed, as a PDF or as a complete kit with pattern, fabric and trims. TPCSH1 is a feminine Pussy bow top with shirt sleeves and a ruffle hem, TPCSH3 has stunning gathered ‘angel’ sleeves which really make a statement whilst the body is kept simple and traditional so that the sleeves do all the talking. 

Lucy offered me the kit of TPCSH2 to try out, it is a box-pleated front shirt, deceptively simple to look at but those details take a little time to get right. It’s classified as ‘moderate/hard’ and I would agree, not because the elements in themselves are especially difficult but each of them needs some experience and precision to execute so I wouldn’t recommend this as your first shirt project. 

The kit comes with enough good quality plain white cotton poplin to make up to the largest size of a UK 22, along with Trend-branded buttons (a nice touch) and iron-on interfacing. All you need to provide is your own thread! 

I started off by taking my measurements and comparing them to the sizing chart, there is also a chart giving you finished garment measurements too which is helpful because it will give you some idea of how oversized the shirt will be when it’s finished. I made a UK 12 and as you will see from the finished photos it’s a very generous fit, to be honest, if you want a close-fitting shirt then this particular pattern won’t be the one for you. 

I opted to trace off the pattern, there are two separate fronts, right and left, and a whole back plus sleeves, yoke, cuffs and collar. There is no pattern piece for the bias binding for the sleeve placket, you just need to cut yourself two bias strips approximately 30cms x 4cms. The right and left fronts are the same except for the extra on the centre front which creates the folded fly with concealed buttonholes. I traced off one front then, to save some time and to ensure they were identical, pinned it to more spot and cross paper before cutting them out together so that I had a mirror version with the additional front added. It’s really important to trace the front very carefully because of the three box pleats, if they are each a bit off you risk the pleats not sewing together accurately which will leave you scratching your head. There are a lot of drill holes to mark the stitching which will eventually hold the pleats in place, don’t be tempted to miss any out because they are also really helpful when you’re folding and pressing the pleats in position. You could choose to trace just half the back to save paper if you intend to always cut it on the fold anyway but having a whole piece gives you the option to have the fabric out flat, besides, it’s almost always more economical to cut fabric out as a single layer [this can be especially helpful if you ever need to do some tricky pattern placement or matching]

Because the fabric is plain, placing the pattern pieces and cutting out was a breeze-no pattern matching, yay! I spent quite a while making traditional tailor’s tacks for every single one of the drill holes. You could use a washable or some other kind of disappearing marker pen if you are confident that it definitely won’t come back to haunt you but I wasn’t going to take the risk on plain white fabric! 

In the past I’ve occasionally found some of the earlier Trend instructions a bit tricky to follow but the more recent ones have illustrations rather than photos and I found this set very clear. My biggest piece of advice would be to read then re-read the instructions before you start, and to highlight anything that you know you’re going to have to really concentrate on, this isn’t a race after all. 

Constructing the fly front and button stand first, including the buttonholes, was satisfying, I often feel like I’ve run out of steam by the end of any project which requires buttonholes and it’s a bit of a chore by then but this gets it out of the way nice and early. [I should add at this point that I started out sewing with a fine size 60 needle so as not to leave too many noticeable puncture holes in the plain fabric if I went wrong or needed to unpick. However, this size needle kept skipping stitches for some reason so I went up to a 70 and had no further problems]

transfer all markings and instructions to the paper pattern if you’re tracing it off. I made tailor’s tacks through every drill hole

My second piece of advice would be to press your pleats on the ironing board if you possibly can. I only have a small heat-resistant board in Threadquarters which meant I was constantly moving the fabric which was not ideal, it was so much easier on the ironing board because the whole piece fitted on. Do not rush this part, with pure cotton fabric you can have the iron on pretty hot but do be careful of your fingers with hot steam. Pin, tack or Wonder Tape the pleats in position once pressed if you want to. 

pressing the pleats on the ironing board, the snips top and bottom along with the tailor’s tacks will help you get each one in exactly the right place.

• 

  I used the horizontal red lines on the foot in relation to the edge of the pleat to give an indication of where to start sewing each bar tack

• 

  I used the ‘needle down’ position so that I could lift the foot whenever I needed to and pull the tailor’s tacks out using my fine-pointed tweezers

In progress-making the bar tacks

The instructions are to stitch down each pleat according to the markings using a few stitches. I did quite a lot of testing using a variety of decorative stitches for this before I committed to the bar tack. The next challenge was getting each of those bar tacks (30 in total!) central over the pleat. My machine comes with a number of feet which are used in conjunction with the decorative stitches and one of these has horizontal red lines which proved very helpful in getting lined up for every bar tack. After making a few of these bar tacks I ‘got my eye in’ so I could tell very quickly where to start each stitch, having the needle stopping in the up or down position is an absolute essential feature on my machine for me and it was brilliant during this, being able to lift the foot to check I was sewing in the correct place without the work shifting was so helpful. The photos will hopefully make my method clearer to follow. It’s vital to take your time and be as accurate as possible during this stage because the box-pleats are the USP of this shirt and it will obvious if they are off-kilter. I sewed in white thread but you could use a colour, or even hand embroider to give your shirt a totally original look.

testing various stitches including triple straight stitch and arrow heads, the difficulty was going to getting every single one central over the pleat

Incidentally, Trend will be creating a series of video tutorials to help so I suggest you check their Instagram account or the website for those. Also, there was a slight problem with pattern markings for the back box pleat which were incorrect. This has been rectified but if you bought a copy very soon after release you might find you have to scratch your head a little, the notches were in the wrong places. Check the website if you’re in any doubt.

the right front, including the fly, taking shape

the shirt with the side seams now sewn up, ready for the sleeves to go in

sewing the continuous binding to the sleeve opening. the instructions don’t call for it but I like to sew across the top of it at a 45 degree angle to encourage the binding to stay on the inside

• 

  finished cuff

• 

  the other finished cuff

close up of the finished front

all done

close up of the finished bar tacks

I followed the order of construction to complete the shirt (I usually do the first time I make a pattern) but personally I would put the collar on after making the yoke. I like to do it before the side seams are sewn up or the sleeves are inserted, unless there’s a technical reason not to obviously. 

the finished back yoke

I popped a bar tack in the middle of the back to hold the pleat in place, this hadn’t had a proper press yet

Everything came together really well, I’ve always found Trend patterns are accurately drafted so I know the pieces will go together well without major discrepancies-this is why it’s so important to trace off carefully if it’s your preferred method, if seams or notches don’t match up you won’t know where the fault lies [the same applies to accurate cutting out too] 

The sun came out so we could take some outdoor photos, I’ve paired the shirt with my much-worn Megan Nielsen Ash jeans

is it a bird? is it as plane?…

I’ve pressed the pleat now

Clearly not everyone will want to make a shirt that is going to take a sizeable amount of time to construct, or to launder afterwards for that matter, but if we only made simple loungewear for ever then the art and skill of making our own clothes will be lost, just at a time when so many people have discovered, or rediscovered, the joy of sewing for themselves. There will always be a place for a classic white shirt and Trend has created a small but growing collection with original twists on the genre. The last year has been so tough for small business owners so I really appreciate being given this kit to try out, I wasn’t under any obligation to review it other than share some photos but personally I have no problem with sewing and writing about it. I will always try to give you a balanced view and if I can support a little business by giving them some positive exposure then I will. Alongside that I’m keen to demonstrate that a design-led style doesn’t have to beyond us ‘ordinary’ sewers either, if you like it then sew it! 

I hope I’ve given you some idea of what will be involved in making the TPCSH2, if you’re looking to push your skills on a bit this could be a good project. Maybe you need/want a plain white shirt in your wardrobe [amazingly I didn’t have one in mine, just a couple of short-sleeved ones] I might layer this with a sleeveless tank top over it, or a waistcoat could look interesting. This is a typical cotton poplin shirting but you could use a variety of fabrics, you could have fun with graphic prints or stripes, try something soft like double gauze or a crisp linen? Or what about harvesting the fabric from several well-worn mens shirts to make a more patchwork look. Take your time though and enjoy the process.

I’ve got a long-sleeved T-shirt under it because it was a chilly day and it will be perfect for the day I can return to the V&A. I don’t know about you but I’ve really missed putting an outfit together to go on a nice day out, deciding which of the lovely garments I’ve made that I want to wear and how I’m going to accessorise them. It seems such a small silly thing to miss but I shall be so glad when I can start doing it again.

Most of all, thank you to Trend for giving me the opportunity to try the kit, until next time,

Happy Sewing

Sue

a multitasking Festive outfit

The Festive season is often a reason to make, or buy, a special new outfit to wear for office parties or Christmas Day but this year’s Festive season things will be very different for most of us. I don’t want to be entirely negative though so, as part of the Lamazi blogger team, I thought I’d make something which is a little bit Christmassy but will double up as a ‘regular’ winter dress too. 

I’ve chosen the cord velvet from Danish Design in a gorgeous shade of aubergine-I’m always a sucker for purple-but it comes in several other beautiful rich shades including a sumptuous gold and a stunning teal too. I picked this fabric because it’s a medium weight stretch jersey and has soft pile which makes it lovely to the touch. I’ve made a dress but you could easily make tops or wide-legged pants in it, or babies and children’s clothes too because it’s washable and crease resistant. 

Whilst I love a complex make to really get my teeth into I felt this wasn’t a garment which warranted lots of time. Making a special Christmas once-worn garment wasn’t appropriate any longer so I wanted something quite simple but adaptable and for that reason I’ve picked the Somerset T-shirt by Maven Patterns. I’ve made a few of these now, the bones of it are beautifully simple, it has a self-neatened bateau neckline, a slightly fitted silhouette and four sleeve options. I’ve chosen the Bishop sleeve with a long cuff but I’ve hacked the sleeve to make it even fuller, and I’ll lengthen the body to create a dress finishing below the knee.

Another idea was to add a flared skirt which looks nice but didn’t think I would use it as much as the straight version.

The Somerset has excellent very full instructions with lots of tips and advice to get a good finish. There’s a useful sheet to write all your information including body measurements and fit alterations, and a fabric stretch gauge to check you have enough stretch for the pattern to fit properly. You can also list the needle type and size you’ve used, stitch type and length and anything else you might want to remember for another time. 

To increase the size of the sleeves I took the bishop sleeve pattern and drew 5 vertical lines from each of the notches from shoulder to hem. Each segment will become slightly wider as it gets nearer the bottom edge so make sure they are even in size.

Cut a piece of spot and cross or tracing paper bigger than the pattern as it is, mark a grainline running right down the paper and then lay the pattern piece on top of it, matching the grain on the pattern to the grain line you’ve just drawn. Next, I carefully cut up to the top of the marked lines taking care not to snip right through at the top, keep it attached by a tiny amount to act as a pivot point. [If you don’t want to cut your original pattern piece I suggest you trace off a new one to use instead] Then you splay the hem edge apart by a few centimetres each, I added 2.5cms between the each of the ‘side’ segments and 5cms to the central one. By doing this you’re adding fullness at the hem but not altering the sleeve head. You could put additional fullness to the sleeve head by opening the top edge too if you wanted. I lengthened the sleeve by 5cms too so that it would have plenty of blousy fullness into the cuff. 

Trace around the new shape using a tracing wheel or pencil and cut out the new piece transferring all markings. One final change I made was to add a bias grainline because I knew I wanted to play with the stripe direction of the rib on the fabric.

I had pre-washed my fabric and partly tumble dried it on ‘low’ before letting it dry completely on the clothes airer, it seemed to survive the experience just fine. 

I made an arbitrary choice of how long to make the dress by simply holding the tape measure at my shoulder and seeing where it came to at about mid-shin! I attached another piece of spot and cross to the bottom of the front and back pattern pieces and drew on the skirt length I wanted, plus a generous hem. I knew I would have to make some adjustments to the hip and thigh during the fitting stage, just make sure that the hip and thigh measurements are plenty big enough because you can always remove some, it’s much harder to add later! 

The ‘cord’ runs across the width of the fabric and I wanted the rib to run down the length of my dress which meant I had to fold the fabric across the width. Try not to twist the fabric if you have to fold this way, I marked a single rib by following it across the width with pins so that I can see it clearly. Fabrics like corduroy, velvet or velour have a pile or ‘nap’ which will shade so if you cut some pieces facing one way on the grain and some pieces running the other way then you will end up with a garment that looks like it’s been made with two different colour fabrics, even though you know that isn’t the case. If you’re unsure what quantity of this type of fabric to buy go with the ‘with nap’ amount on the pattern information and follow the one-way layplan to cut out.

I marked the rib across the fabric with pins so that I could be sure it was folded correctly and would not be twisted.

Once I’d cut all my pieces I followed the making instructions which are very comprehensive. If you have a walking foot for your machine I strongly recommend you use it because velour like this has a ‘pile’ and has a tendency to ‘creep’ as you sew so you might find that it starts off with all the edges matching but by the time you get to the other end the two fabrics are no longer matching. I also strongly recommend you tack any seams you are unsure about. You could use a million pins but by the time you’ve done all that you could have basted it in place which does the same job and usually more effectively. I was able to coverstitch the neck and the skirt hem on the Pfaff Coverlock 3.0 I have on loan as a brand ambassador but it works just as well by overlocking the raw edges and twin-needle stitching them down, or zigzag and twin-needle, or two rows sewn singly if you don’t have a twin needle. When it comes to pressing a fabric like this, if you don’t have a special needle board (and few of us do) then you should press on the reverse at all times. You could place a towel on your pressing surface and lay the fabric on top so that the pile of the cloth is against the pile of the towel which will help protect it. Use a pressing cloth as well. These tips will also apply to regular corduroy or any non-stretch fabrics with a pile too.

The bell of the sleeve is gathered using shirring elastic which helps to retain some of the stretch required for the cuff. 

Once the sleeves were in I sewed up one side seam directly on the overlocker and then pinned the other side seam to fit myself. This was because I didn’t know if I’d need a split at the hem to be able to walk in the dress and I didn’t want to end up with loads of unpicking!

First I tried it right side out to get an idea of how it was fitting initially, then I turned it inside out to pin.

I looked at the fit in the mirror first of all and the sewn side seam was quite wavy, this could be cured by either adjusting the differential feed on the overlocker so that it doesn’t happen, or you could stitch the seam on the sewing machine and then overlock the edges [This is what I opted to do because I could see I had to take a fair bit off the side seams anyway to achieve a fit I was happy with] Then I put the dress on inside out in front of the mirror and pinned out the excess. I turned it right side out and tried it on again to check the fit, then finally sewed both side seams on the sewing machine, I used a ‘stretch’ needle, a ballpoint or jersey needle performs the same task. Either use a short straight stitch or a straightened out zigzag, make some samples to see which works best for your particular fabric. 

Now I tried it on the dress inside out to adjust the seams

I pinned out a fair bit of the side seams to give more shape through the waist and hips.

still Inside out

Finally I put the pinned dress back on the right way around to check I was happy with the fit before making the adjustments.

Lastly, the cuffs go on and the skirt is hemmed. 

And that’s pretty much it, it pops straight over the head so no tricky closures, because of the stretch it didn’t need a split, and that means there’s room for Christmas lunch and it won’t look like a dish rag after spending the afternoon curled up on the sofa watching Christmas telly!

cheers!

I’ve dressed it down with an ancient knitted gilet plus a wide belt, long boots and my much loved Alexander McQueen scarf

I love a scarf to keep my neck warm!

It could be the strangest of Christmases but let’s raise a glass to a much better 2021

I have to say that I’m really happy with this dress because it ticks all the boxes I wanted it to. It’s comfortable but it looks Christmassy, it looks great with opaque tights, heels and jewellery, but also with boots, a chunky belt, a roll neck top underneath for extra warmth or a cosy scarf…and did I mention it’s comfortable! #secretpyjamas It also has the advantage of rolling up and going in the corner of a bag or suitcase and coming back out again not needing a press. Bonus!!

If you have a favourite T-shirt pattern you could try lengthening it into a dress, Tilly and the Buttons Tabitha from Make it Simple does that. You could browse the SewOver50 post I wrote listing loads of go-to T-shirt patterns for inspiration, or maybe copy a RTW one you already have?

At 160cms the fabric is very wide so a little will go a long way, and because it’s so soft it would be lovely for children’s wear too. It needs a little bit of careful handling but a lot of that is in the ground work. Make sure you lay it up and cut it accurately to minimise unnecessary stretching or distortion (try to keep it flat on the table or lay it up on the floor) pin or tack the seams so they don’t move about and press carefully as you go and you should be fine. 

It’s been an incredibly tough year for so many and I wouldn’t blame you for not feeling like making anything new to wear. However, if crafting and creating bring you joy and respite then you could view it as a gift to yourself, and when you choose to buy from small companies like Lamazi and Maven then you are helping them too.

Thank you to Lamazi for providing me with the fabric for me to write my review, and I hope you find it helpful. 

Until next time, Happy sewing

Sue

Pfaff air threading and a Tesselate Tee!

There’s a lot going on in this post because I’m offering you my thoughts on not one product but three! 

So, a bit of background first…I used to be a keen runner but various injuries forced me to stop and then I never quite got started again. Fast forward at least 3 years and I’d gained weight which I wasn’t happy about, I felt sluggish and lacking in energy, I wanted to lose the weight for the good of my health and mental wellbeing. So, coming up to date, the return to running is going well (if cautiously…) and I’m losing some weight which in turn has inspired me to try making some of my own activewear. Fortunately for me Melissa Fehr of Fehrtrade has become a sewing friend of mine since first meeting her at the Sewing Weekender a few years ago and she generously offered me a copy of her Tesselate Tee pattern to try. I’d helped test her Rouleur leggings last year so I already had that pattern. Part of the beauty of Melissa’s patterns is that she gives you really comprehensive instructions to be able to sew activewear using just a regular sewing machine if you don’t own an overlocker. I’m in the fortunate position at the moment to be a Pfaff Brand Ambassador and I have their air-threading Admire Air 5000 on loan, along with a Coverlock 3.0 as well so this all seemed like the perfect opportunity to make some new running kit. 

Suitable activewear fabric is not something I have in my stash other than the scraps left from testing the Rouleur leggings so I had a little online search and came across Frumble fabrics. They have a good range of activewear fabrics at competitive prices as well as an impressive selection of suitable elastics and other trims or haberdashery you might need for this sort of project. I bought a metre of plain navy fabric and a metre of navy camouflage print, along with navy soft waistband elastic, some navy fold-over elastic and, finally, silicone grip elastic. [One point I should add here is that I decided not to pre-wash the fabric, this was based on my own knowledge and belief that synthetic fabrics are usually more colour-fast than natural fibres. I was wrong. The navy came off on my hands as I was making it up so as soon as I finished both garments they have been through the wash after all. I have alerted Frumble so I’m not saying anything here that I haven’t already fed back to them. Overall I’m pleased with the fabric quality and I learned my lesson-prewash even if you think it doesn’t need it!]

I opted to go for a medium size Tesselate top, Melissa has recently layered the pattern so now you only need to print off the size or sizes that you want, I wavered between small and medium according to my measurements. The small probably would have been fine but the medium gives me a little more room without the constant thought that I should be sucking in my wobbly bits! One of Melissa’s USP’s with her patterns is interesting seam lines which means, as well as striking designs, you can often use up small pieces or remnants of suitable fabrics. The Tesselate has a variety of options including short or long sleeves, thumb cuffs, a hood (with ponytail hole!) and back zipped pocket. 

I cut the leggings a mixture between small and medium and I’m happy with the fit of the end result. I had enough fabric for long sleeves on my Tesselate and, although there’s a pattern for the back pocket, rather than print it off I made my own. 

I opted to put the pocket in the back left diagonal seam because I decided I could reach it comfortably behind me and use the zip easily whilst moving if necessary. I drew onto the pattern how big it needed to be to accommodate the essentials.

I placed spot and cross paper over the top and traced off the shape, adding 1cm seam allowance to it.

a new pocket bag labelled and ready

I played around with the fabrics until I was happy with their placement, I had enough of the blue spotty fabric for the back and front side panels, everything else I divided between the two navy fabrics.

Because I was going to be sewing a fair bit of the garments together directly with the overlocker I join the pieces with the pins at least 2-3cms away from, and parallel to, the cut edge. Then it’s safe to sew without the pins being anywhere near the blade.

I’ve made another little video to demonstrate how the air threading works on the Pfaff, you’ll need to bear in mind that it might seem like it takes a while to thread and so where is the advantage in air threading but that’s because I’m trying to explain as I go and I was sitting at a funny angle behind the camera whilst I did it.

After two years of owning the Quilt Ambition 2.0 (now discontinued) I’m used to the quality of Pfaff machines so it doesn’t surprise me that the Air Admire is sturdy (no shifting about on the table while you sew) and very speedy, with a superb quality of stitch. It doesn’t take long to get to grips with the air threading and, as I mention in the video, there’s an automatic threader for both needles too! I couldn’t get the hang of that at all to start with but it’s amazing what a difference it makes if you read the instructions and follow them! Of course, this is an expensive machine and I understand that not everyone will have that kind of budget but if you are considering an air threading overlocker (there are now a lot more models on the market than just market-leader Babylock with prices gradually coming down) then this one is most definitely worth thinking about.

I inserted the invisible zip on the sewing machine, then attached the pocket bag that way too. The T-shirt goes together pretty quickly considering the number of pieces-most pieces are cut singly because they are asymmetric-if you’re using the same fabric throughout it would be an idea to label your pieces in some way so you don’t get them mixed up.

I find it very useful having a variety of stitches to choose from especially when sewing with stretch fabrics, the 3-step zig zag was ideal when I was sewing the elastic into the waistband, I also have an ‘elastic’ stitch which is useful. A lot of machines, even quite simple ones, will probably have a stitch option which will enable you to sew activewear so why not try out a few of them to see exactly what they are, the instruction book should be helpful, or there’s so much information on the internet too.

The finished waistband on the leggings, elastic is completely enclosed in a seam at the top and then I’ve secured it further with a 3-step zig zag stitch

I’ve joined the elastic for the legs into loops which are then sewn to the right side of the fabric, matching the edge of the elastic to the cut edge of the fabric.

I used a small zig zag to stitch it in place. This then flips to the inside and I coverstitched it along the top edge.

To neaten the hems and around the neck I swapped over to the Coverlock 3.0 which I had on the coverstitch setting. Again, this is a very sturdy piece of kit with excellent stitch quality, I am finding there is a certain knack to using it and I’m by no means an expert yet but it certainly gives a very professional finish to knit, jersey or stretch garments.

The Rouleur leggings also have large side pockets which are perfect for holding your phone and/or keys etc (Betsy getting in on the act again too)

As always, I hope you’ve found this helpful, I always try to be honest about how I get on with a product whether or not I’ve been gifted, loaned or purchased it-all three in this case. If you’re tempted to have a go at activewear then Melissa is a good place to start-she’s even written a book on the subject so you’re in good hands!

Until next time, happy sewing

Sue

Dawson Coatigan by Thrifty Stitcher

I followed the progress of this pattern with interest on Instagram when it was originally released nearly two years, it was fascinating to see how Claire-Louise Hardie (the Thrifty Stitcher!) developed and finessed the various elements of it as she sampled it, up to the point that she was ready to release it for sale. It has attractive style lines with princess seams in the front which curve into hip pockets, the back also has princess seams and there’s a horizontal seam just below the natural waist. The collar curves up smoothly against the neck and the back collar has a ‘sunray’ of five darts spreading out towards the shoulder blades which I particularly like. The cuffs each have 3 similar darts, the details on this pattern has simple but so stylish.

My copy is a paper pattern but it’s now a PDF available from CL’s own website.

This post was originally published last year by Minerva who generously provided me with a nice firm Ponte Roma in a plain navy to make the Dawson in, it would also work very well in a boiled wool, felted wool, Melton, not a loose tweed though as they can start to fray and you’d lose the details too much in the weave. Anything fairly structured and stable would effectively show off the style lines. You could get some interesting effects with checks or stripes if you want a challenge! I’d wanted to make another version for a while because I’ve had really good use from the navy one, I hadn’t got around to finding any specific fabric for it but then I hit upon the idea of using a single old heavyweight cotton curtain that used to keep the drafts out by our front door. It had long been replaced for this task but I just had it folded up underneath the heat-reflective mat that I use on my cutting table. In order to maximise the fabric in the curtain I undid the deep hem and the sides, and removed the tabs at the top. I gave it a wash to clean it but also to, hopefully, stop it shrinking later on.

Areas like the pocket edges and the neck need stabilising with some iron-on tape or strips of interfacing as per the instructions, especially if you use a knit fabric like Ponte. I would recommend stabilising the shoulders with seam tape or scraps of ribbon to prevent stretching too. I used a specific needle for stretch fabrics and you could use the ‘lightening’ stitch to sew with if your machine has it, or a very straightened out zigzag. If you do use boiled wool the layers could be quite thick, use a straight stitch but you may need to lengthen it a little more than usual.

The pattern comes in eight sizes which are not numbered in the conventional way, CL opts for letters instead, so you work from your own body measurements to choose which size should fit you. I cut and sewed a size F originally which was quite generous, for the newer version I’ve cut the next size down. I misjudged how generous the ease is in the garment so I usually wear the Ponte version layered up over jumpers or sweaters on warmer cool days if that makes sense. At the end of the day it’s intended as a casual coat so don’t make it too small as you’ll always be pulling it closed across you. The sleeves are nice and roomy too, I’ve noticed some coat/jacket patterns can be a bit snug around the bicep for me which is a bit dispiriting, I’m hardly a muscle-bound hulk! Just check before cutting out if you’re happy with the sleeve length too, I probably could have added just 3-4cms because it feels the tiniest bit short on me.

The pattern goes together beautifully and all that tweaking in the sampling stage is borne out in the final version. I found the instructions pretty clear, they are mostly photographs and there are some really useful hints and tips which will come in very handy if you aren’t that experienced in your dressmaking yet. Make sure you transfer your markings for the pocket pivot point for example so that you get a crisp finish for the corners.

You could top stitch all the darts down, possibly in a contrast thread if you like, but because the Ponte had a slight stretch I didn’t do this on mine. I did top stitch down the front facings though and caught them down in a couple of places on the inside to stop them flapping. 

For the ochre version I topstitched more of the seams, I confess that I was incredibly slovenly and used up various threads in my collection so not all the stitching is the same colour…oops! Incidentally I didn’t use top stitch thread, instead I used the triple straight stitch which looks very similar although it is quite thread-hungry (hence the non-matching!)

This time however I didn’t top stitch the front facings down, I adopted a different approach. As it’s an unlined coat so all the innards are visible I used some ribbon to anchor the facing down in a couple of places. I chose to do this because I know from experience that when you’re sewing through several thick layers the triple stitch (which is a set length on my Pfaff and not adjustable) it can lead to puckering which doesn’t look so nice. Try a sample before you go ahead if you aren’t sure, that’s a LOT of slow unpicking if you don’t like it after all.

ribbon tabs between the facing and the pocket bag stop the facing from flapping about too much

You can see from this shot where I’ve placed the ribbon anchors.

I finished the hem by hand using a herringbone stitch rather than machining it for the same reason that I didn’t top stitch the front facings.

I think the Dawson is a well-drafted and executed pattern from an independent designer (and CL’s art work features herself so it squeaks into the #so50visible category!) The Minerva Ponte Roma works well for the soft tailoring, using my old curtain gives the slightly cocoon-shape a little more definition. It shouldn’t be too difficult to do an FBA if you need to either. I’m much happier with the fit of the ochre one, but I love the navy and will still wear it regularly too.

cheer up love!

Because the Dawson is a loose cocoon shape it would make a beautiful evening coat in a glamorous brocade, to go over the top of your evening outfit, denim would look great too (Have a look at my Simple Sew Cocoon jacket in denim here)

I guess this was also a useful exercise in upcycling, the curtain was years old and not being used for it’s original purpose so I thought why not give this a try. If I found I wasn’t mad about wearing the colour after all I know it’s 100% cotton so it would dye, I might come unstuck with the polyester sewing thread though which would take up the colour differently-it’s hardly Saville Row standard though! The Dawson took barely two metres of fabric (the front facing is helpfully cut in two parts which helps reduce the fabric usage, and of course you could always use a contrast fabric anyway) it doesn’t instruct you to use interfacing on any of the collar or facing parts but I did, just to stabilise the fabric a bit.

Until next time, Happy sewing

Sue

My second Lamazi blog post

Much as I’m a big fan of sewing and wearing dresses, I do love separates too, especially tops. I think this version of the Amaya shirt by Made My Wardrobe may just have gone to the top of my favourites list! [Full disclosure, Lydia offered me my choice of one of her patterns as a PDF with no expectation of a review and I selected the Amaya with its gathered neckline, raglan sleeves and full floaty cuffs] I printed it off but then didn’t start it for a while until the ‘right’ fabric came along.

As a Lamazi Fabrics blogger we each volunteer for a number of slots throughout the year but Liana was short of a post for early August so I offered to do it. I thought the Amaya would be a good option as it’s not complex and I could probably sew it quite quickly to meet the deadline. When my eyes fell on the beautiful printed Broderie Anglaise I knew I had my perfect match! 

When the fabric arrived it was absolutely gorgeous, so soft and pliable. Broderie Anglaise can often be quite stiff and crisp, which may be what you want, but I’ve also found it to be a disguise for a cheaper quality cotton fabric with lots of dressing or starch in it so do be slightly wary of very cheap Broderie Anglaise. This version is a printed soft cotton lawn which is then embroidered, there are lots of eyelets so personally I’ll probably be wearing a plain-coloured RTW camisole underneath as no one needs to see my undies or midriff thank you! This specific fabric does not have an embroidered edge which some Broderie Anglaise does, and also be aware that the embroidered part of the fabric doesn’t run right up to the selvedge, this is normal with this type of fabric. On this particular fabric there’s a wider gap down one side than the other so you may find the useable part of the fabric isn’t as wide as you would think. In other words, don’t scrimp on the quantity of fabric when choosing Broderie Anglaise for a project because you could find yourself a bit short by accident.

I opted for a UK size 14 with no modifications according to my measurements but I think I will go down a size when I make another, the fabric you choose could make a significant difference to the finished look so a soft and floaty georgette or silk crepe de chine for example would look divine with plenty of volume but a firm linen, or a cotton poplin could give you the appearance of a ship in full sail! (that may, of course, be the look you’re after!) 

This fabric has a one-way design but I chose to turn the upper sleeve pattern piece to interlock better and make it more economical to cut out, I really don’t think it’s that obvious on the finished garment, always worth checking though! 

It’s pretty well impossible to see snipped notches or even triangles on this fabric so, in order to tell the front of the sleeve from the back, I marked the single and double notches with long thread tacks and this seemed to work well.

• 

• 

I used a French seam finish on the cuffs but found there wasn’t any particular advantage to doing this, for the rest of the construction I sewed regular seams and overlocked them together. 

The pattern calls for interfacing to be attached down the centre front seam to stabilise it but I chose not to do this as it would show through the eyelets, I simply neatened the edge of the self-facing with the overlocker. I had a rummage through lots of the miscellaneous trims and ribbons I’ve had from past projects and tried a few ideas out with them but in the end I only used a white cotton trim down the front and simple edging lace on the sleeves, I would have used this on the hem too but there wasn’t enough, more on that later. 

I added a triple zigzag stitch to embellish the sleeve ruffle seam too.

The neckline is gathered up into a bias-cut band but instead of cutting it on the bias I used a straight strip of the printed lawn from near the selvedge. I did this because a bias strip of such holey fabric wouldn’t have worked well at all, the one drawback of the tie being cut on the straight is that it doesn’t curve around the neckline quite so smoothly but it’s fine. The tie is topstitched close to the edge so, to match the sleeve, I used the triple zigzag stitch again. 

Finally I had to finish the hem, I could simply have turned up as per the instructions but I wanted some kind of pretty finish to echo the cuffs. As I didn’t have enough of the sleeve trimming, or any other edging lace which I felt worked alongside what I’d already used, I opted to try out one of the satin stitches which my Pfaff machine is capable of. 

I’d never tried this before so I did a couple of experimental tests with a few stitch designs that appealed to me, I used Vilene Stitch N Tear as a backing behind it to stabilise the fabric.

This seemed to be satisfactory so I sewed the whole hem by this method a few millimetres away from the edge. The Stitch N Tear is then carefully torn away to leave the actual embroidery and then finally, as accurately as possible, I snipped away the excess fabric to leave the pretty scalloped edge.

I’m very happy with this finish on the hem BUT it’s just possible that it might not be very durable in the wash, I’m half-expecting that it might start to come away in places. If this happens then I’ll have come up with another idea but for the moment it looks nice. 

I hope you’ve found my tips for working with Broderie Anglaise helpful, and things to look out for with it. It’s certainly a fabric that is having a ‘moment’ at the moment, it’s timeless and feminine and I’m looking forward to wearing my Amaya for a few years to come. 

• 

Thank you as always to Lamazi for providing me with the fabric to be able to write this, and thank you to Lydia at Made My Wardrobe for generously giving me the pattern. 

Until next time,

Happy sewing

Sue

I made a Sew Over 50 video!

I thought I would share with you the video I made specifically for the recent Sewing Weekender here in the UK for anyone who wasn’t able to, or wasn’t interested in attending. Unlike previous years, when the event takes place over two days in Cambridge, this one was entirely online and so the organisers, Kate and Rachel at The Fold Line and Charlotte @englishgirlathome asked an impressive selection of contributors to make short videos on a variety of topics. I’ve never made a film before so it was a pretty steep learning curve!

The first challenge was going to be filming it, and then it would have to be edited in some way too. I worked out that if I balanced my phone on top of my sewing machine in my workroom it was at the right sort of height with good light. Then I decided I needed a script of sorts to keep me on track and that is what I’ve reproduced here, along with the video itself. I printed it out and stuck the sheets to the window and to the sewing machine like a kind of ramshackle autocue! It turned out the window was too far away though and I looked like I was gazing to the heavens for divine inspiration…how to vloggers do this all the time? Maybe they do just waffle on and nobody minds? hey ho, I knew the things I wanted to say and without some kind of prompt I might forget some of them. Anyway, I managed to film it in bursts although I did have to pause one time to shoo the pigeons off the roof because they were audibly clumping about and I didn’t need that distraction too! I found my laptop has iMovies so I managed to splice the whole thing together using that, the next Jane Campion I am not!! The script below is not word-for-word what I said because I managed to freestyle it a couple of times in an attempt to sound natural but for anyone with hearing difficulties it’s close enough, I’m afraid subtitles were absolutely beyond my rudimentary film-making abilities.

I hope you’ve all been enjoying the Online Sewing Weekender and I want to begin by thanking Kate and Rachel of The Fold line and Charlotte from English Girl at Home for taking the very brave and audacious step of carrying on with the event in spite of the strangeness of the times. It’s so great to imagine all of us sewing away at the same time wherever we are in the world.

As well as my own Instagram account I’ve also been involved with the SewOver50 account since the very beginning and whilst Judith and Sandy manage the account on a day-to-day basis I write the blogs which accompany particular discussions or any challenges which have been running.

When Kate, Rachel and Charlotte invited me to be involved I thought I’d chat a bit about the #so50visible challenge involving indie patterns in particular. It first ran in February last year and then again this March.

The reason SO50 began in the first place was because we felt that our slightly older age group was being overlooked by the burgeoning home sewing industry and we really didn’t want it to become as age-centric as the mainstream fashion industry has always been. Plus many of us bring a wealth of knowledge and experience which we’re only too happy to share with anyone new or maybe returning to dressmaking at home. 

Many of you will know that the dress pattern market has been dominated for many decades by the so-called Big 4 but in the last 10 years or so there’s been a boom in independent designers putting out their own patterns.

Followers of SO50 have embraced these indie designers with gusto but we also felt a little bit side-lined by them too. We didn’t often see ourselves being reflected back on the packaging or marketing. 

The #so50visible challenge was created to draw some attention to ourselves, to highlight that very few older sewers were featured, and to politely encourage a change of thinking. 

We came up with the idea to ask people to only sew a pattern which featured an older model in it’s advertising and promotion.

Judith and I spent an absolute age trawling through the Fold Line database and eventually came up with quite a modest list considering how many patterns are listed! We found a few books with older models too. 

Throughout the month long challenge followers were asked to share their makes, it meant many people found new brands of pattern maker which we might not have heard of before. Very often the most popular patterns were stylish, fashion-forward and wearable but the model looked more like us. Many of SewOver50’s followers are still very interested in fashion and style and we still want to look good whilst making our own clothes. 

Many of us in our 50s and 60s have more time to sew for pleasure and we might have more cash to spend on patterns and fabric too so it always strikes me that it’s a missed opportunity for indie pattern makers to disregard this huge potential market. 

While the first challenge was running we also introduced the #so50thanks hashtag because if anyone’s make was reposted by the designer we thought it was important to appreciate that they had first of all noticed and acknowledged the maker and that they were then happy to share it on their own feed. 

It’s a virtuous circle isn’t it? Feature an older model on the pattern and it gets our attention, we buy your product, we share our makes, SewOver50 probably reposts to it’s 20K followers, you get free advertising to an audience with money to spend, and more people will buy the pattern because they can imagine themselves wearing those clothes-simple! 

There are a few brands which have always been great at using a diverse range of models including Paper Theory, The Maker’s Atelier, Cashmerette, Pattern Union, Style Arc and Grainline for example, and Closet Case patterns have recently named their newest release Blanca after one of our most stylish and inspiring SO50 stalwarts, which is just fantastic and very exciting.

As well as pattern brands there are also a number of books including those by Wendy Ward and Everyday Style by Lotta Jansdottir with a real cross-section of models in them. 

There are a few other companies like Maven and Alice & Co who don’t use models at all, just illustrations or mannequins but they are super-supportive and involved in our community and constantly share and repost. Let’s be honest here, most of us are pleased to get a like or a repost because it gives us a little boost that the designer noticed us, we can all gain ideas and inspiration from others, and we want to see the garments being worn by people who are similar to ourselves in some way. The pattern companies which do notice us have then tended to become very popular with SO50 followers, it’s that virtuous circle again. 

We think there’s a small element of change happening but there’s a long way to go, though there are more companies than just the ones I’ve had time to mention here and there’s always room for more. 

I’m always happy to share the knowledge and experience I have from many years of sewing, and I know of many others who are too. It’s fantastic to be a part of this worldwide sewing community and it’s diversity is vital so if we can encourage a few more indie brands to look beyond the young, slim, white stereotype then that can only be a positive thing right? 

Enticing us to spend our grey pounds (or dollars) is a good reason to check out what the followers of SewOver50 are up to especially as there are now almost 20,000 of us! And I will often write honest reviews of patterns or fabric over on my blog which you might find interesting too, I like to think I’m a critical friend. I would encourage anyone to look at the #sewover50 hashtag because there are now tens of thousands of images to inspire you.

Anyway, I hope you’ll enjoy the rest of the Sewing Weekender wherever you are, and I hope whatever you’re sewing is going well, with any luck we will have opportunities to meet again in real life before too long, I do hope so. I love going to meet-ups and being able to chat with fellow sewers, and filming myself like this is a first for me so I hope it’s made a bit of sense! 

Thank you again to Kate, Rachel and Charlotte, 

Bye bye etc etc…

I spent both days of the Weekender on a video call with two of my sewing buddies Melissa Fehr and Elizabeth Connolly, I met them both originally at the first Weekender and we’ve all been fortunate enough to go to every one since, we weren’t going to let a pandemic stop us this time! I made another Camber which was one of the projects I cut out on my recent batch cutting splurge and I added a machine embroidery stitch from my Pfaff Quilt Ambition 2.0.

• 

• 

• 

• 

  The Camber Set by Merchant and Mills

Me, Melissa and Elizabeth on Melissa’s phone perched in her workspace!

Over the course of the weekend over 1900 people joined in by buying a ticket, and all the profit from ticket sales which totalled over £23K were donated to four fantastic charities, NHS Together, Mind, Stephen Lawrence Trust and Black Lives Matter.

If you’ve ever read any of my previous blog posts you’ll know I really enjoy going to meet-ups so not being able to do this for the last few months has been sad to say the least, with luck it won’t be too much longer though. To my mind, this year Charlotte, Kate and Rachel have successfully created the next best thing because everyone could sew whenever and wherever they were in the world. Some did as I did and had group chats going on, two sewers I know set up their machines on trestle tables in the garden (suitably distanced of course!) others were solo but had all the video content to keep them company or by using the #sewingweekender hashtag, some didn’t/couldn’t really join in with sewing on the day for one reason or another but took part in the giant Zoom at the end of Saturday, or early afternoon on Sunday. The Zoom was fantastic because it made me realise just how many people from all over the world had been participating including the US, Canada, Germany, Norway, Israel and Australia, and hearing so many shout-outs for SewOver50 from them was even better! Everyone, whatever their situation or circumstances, had the opportunity to buy a ticket-which was essentially a charitable donation anyway-it will be interesting to see if this is a format that could be repeated in the future to make the event inclusive worldwide. Were you ‘there’? what did you make of the concept, and was it preferable in some way to the real life event for you, or not as good? I’d be interested to hear your thoughts

Until next time, happy sewing,

Sue

Two Minerva makes in one go!

I originally wrote this as a review for the MinervaDotCom blog but I’m not actually sure if it ever appeared. Rather than waste my efforts I thought I’d publish what I wrote here instead.

I’m sure it was a combination of an over-generous stated fabric requirement, my just-to-be-on-the-safe-side ordering and then super-stingy cutting out means that I managed to get not one but TWO sweatshirts out of my Minerva fabric choice this time. At the time of writing last autumn, Minerva were introducing a collection of textured jerseys made in a polyester/ viscose/ spandex mixture which came in a wide range of colours and textures so I opted for a geometric design in lilac to try out. I would suggest that this fabric is not as firm or thick as some jerseys suitable for sweatshirts, it isn’t fleecy on the reverse for example but it has reasonable drape, is soft to the touch and has a fair amount of stretch but not in a ‘really difficult to control’ kind-of way (it isn’t like lightweight jersey for T-shirts for example) it’s actually pretty stable so manipulates well into armholes or cuffs. 

I already had a pattern I wanted to try, the Maxine sweatshirt by Dhurata Davies that has interesting diagonal seams across the front which have pockets in them. This actually made cutting out a whole lot more tricky than I anticipated because the ‘check’ design of the fabric I had picked turned out not to be square but rectangular so matching the lines was a real challenge. In some areas I’ve failed so my advice would be “don’t choose a pattern that has too many intersecting seams or style lines” because you could end up tearing your hair out when you can’t get it to match! Once I’d committed though I decided to press ahead and settle for ‘almost but not quite’…not my usual route but there we are.

When it became apparent that by folding and cutting really carefully I’d have oodles of fabric left over I pulled out a very simple sweatshirt pattern Simplicity 8529 and cut that at the same time. You might recognise this pattern as the Toaster sweater by SewHouseSeven if you think it looks familiar. If you fold the selvedges in towards the centre so that you have two folds then it’s often possible to get more pieces out of less fabric, any sleeves, yokes or facings can be cut out of what remains.

I currently have a Pfaff Coverlock 3 on loan to me so I used it to sew up much of the two tops on it’s 4-thread overlocker setting but you can easily sew this fabric on a regular machine, just use a ballpoint or stretch needle and set your machine to a very elongated zigzag if you can (regular stitch length and a narrow width) or a ‘lightening’ stitch if your machine has it. Unlike some jerseys or sweatshirting you’ll definitely need to neaten the seams though because I found the fabric frayed and went fluffy at the cut edges quite badly as a result of the woven nature of the surface design. Use a zigzag stitch on the edges if you have limited options, or pinking shears. 

the cut edges fray like this a little bit.

the Pfaff Coverlock 3.0, it’s been a fantastic machine and the quality and versatility of its stitching has been superb.

The ‘Maxine’ is a great design which stands out in a crowded field of many other sweatshirts and the well-written instructions and diagrams are very clear and simple to follow. The tricky area could be the point at the centre where the seams intersect, I simply made this more complicated for myself by choosing the geometric design! And of course it has pockets! I’ve made another version of it since the lilac from a remnant of linen/wool which you can read about here.

Maxine sweater in linen/wool mix from Merchant and Mills

• 

  the finished Maxine sweater

this is a slightly truer version of the colour

The Simplicity/Sew House Seven pattern has a very simple ‘grown-on’ collar and self bands on the cuffs and hem. I cut and made this one up in less than two hours and it shows off the textured surface of the fabric very well. 

Simplicity 8529 with cuffs and hem band finish, I like this top so I think I’ll make another next winter but do the longer straight version.

You’ll notice that neither top is long but I’m happier to be able to make two shorter but perfectly wearable tops rather than one longer one with fabric left over which wasn’t enough to use for anything else.

I would suggest that this fabric will make very comfortable loungewear like track pants, tees, sweatshirts, dresses and children’s wear. I don’t know what the other designs in the range are like but if you are pattern match averse then this particular one might not be for you! I thought at the time it would be interesting to see how well a fabric with a raised surface texture like this wears and now that several months have elapsed I’ve found that it catches quite often and has started to pill quite significantly which is disappointing given the price per metre.

My thanks to Minerva for providing me with the fabric to write about, this is a significantly different version of the blog post which may, or may not, have appeared on their website. I did try to find it but their search function doesn’t make it very easy to find specific posts.

Until next time,

Happy Sewing,

Sue