I originally wrote this as a review for the MinervaDotCom blog but I’m not actually sure if it ever appeared. Rather than waste my efforts I thought I’d publish what I wrote here instead.
I’m sure it was a combination of an over-generous stated fabric requirement, my just-to-be-on-the-safe-side ordering and then super-stingy cutting out means that I managed to get not one but TWO sweatshirts out of my Minerva fabric choice this time. At the time of writing last autumn, Minerva were introducing a collection of textured jerseys made in a polyester/ viscose/ spandex mixture which came in a wide range of colours and textures so I opted for a geometric design in lilac to try out. I would suggest that this fabric is not as firm or thick as some jerseys suitable for sweatshirts, it isn’t fleecy on the reverse for example but it has reasonable drape, is soft to the touch and has a fair amount of stretch but not in a ‘really difficult to control’ kind-of way (it isn’t like lightweight jersey for T-shirts for example) it’s actually pretty stable so manipulates well into armholes or cuffs.
I already had a pattern I wanted to try, the Maxine sweatshirt by Dhurata Davies that has interesting diagonal seams across the front which have pockets in them. This actually made cutting out a whole lot more tricky than I anticipated because the ‘check’ design of the fabric I had picked turned out not to be square but rectangular so matching the lines was a real challenge. In some areas I’ve failed so my advice would be “don’t choose a pattern that has too many intersecting seams or style lines” because you could end up tearing your hair out when you can’t get it to match! Once I’d committed though I decided to press ahead and settle for ‘almost but not quite’…not my usual route but there we are.
When it became apparent that by folding and cutting really carefully I’d have oodles of fabric left over I pulled out a very simple sweatshirt pattern Simplicity 8529 and cut that at the same time. You might recognise this pattern as the Toaster sweater by SewHouseSeven if you think it looks familiar. If you fold the selvedges in towards the centre so that you have two folds then it’s often possible to get more pieces out of less fabric, any sleeves, yokes or facings can be cut out of what remains.
I currently have a Pfaff Coverlock 3 on loan to me so I used it to sew up much of the two tops on it’s 4-thread overlocker setting but you can easily sew this fabric on a regular machine, just use a ballpoint or stretch needle and set your machine to a very elongated zigzag if you can (regular stitch length and a narrow width) or a ‘lightening’ stitch if your machine has it. Unlike some jerseys or sweatshirting you’ll definitely need to neaten the seams though because I found the fabric frayed and went fluffy at the cut edges quite badly as a result of the woven nature of the surface design. Use a zigzag stitch on the edges if you have limited options, or pinking shears.
The ‘Maxine’ is a great design which stands out in a crowded field of many other sweatshirts and the well-written instructions and diagrams are very clear and simple to follow. The tricky area could be the point at the centre where the seams intersect, I simply made this more complicated for myself by choosing the geometric design! And of course it has pockets! I’ve made another version of it since the lilac from a remnant of linen/wool which you can read about here.
The Simplicity/Sew House Seven pattern has a very simple ‘grown-on’ collar and self bands on the cuffs and hem. I cut and made this one up in less than two hours and it shows off the textured surface of the fabric very well.
I would suggest that this fabric will make very comfortable loungewear like track pants, tees, sweatshirts, dresses and children’s wear. I don’t know what the other designs in the range are like but if you are pattern match averse then this particular one might not be for you! I thought at the time it would be interesting to see how well a fabric with a raised surface texture like this wears and now that several months have elapsed I’ve found that it catches quite often and has started to pill quite significantly which is disappointing given the price per metre.
My thanks to Minerva for providing me with the fabric to write about, this is a significantly different version of the blog post which may, or may not, have appeared on their website. I did try to find it but their search function doesn’t make it very easy to find specific posts.
A lot has happened since I wrote my last Simple Sew blog post, Christmas for one thing, and I had a lovely holiday in the sunshine too but now we are all confined to our homes because of Covid 19. Without wishing to trivialise the gravity of this situation, one of the side effects of it is that you might have more time to sew.
I’ve had a rummage through my Simple Sew patterns to find one which I haven’t already shown you, and which has opportunities to hack, and I settled on the Chelsea Collection. This is a capsule wardrobe of a short sleeve blouse with two variations, a pair of trousers and a button-front skirt in two lengths. I liked the blouse with it’s shirred sleeves and keyhole back detail but I decided to mix it up a little by adding a button front. Normally we are able to select fabric from a couple of generous sponsors but I wanted to ‘shop my stash’ to find something this time. I found a very pretty vibrant floral John Kaldor cotton lawn which I think I picked up from a swap table sometime and I knew would work well for the blouse.
I didn’t want the blouse to be overly tight so, after checking my measurements I opted for a larger size than I’ve made previously. If you’ve been a regular reader of my posts you’ll know that I tend to check Simple Sew patterns for any discrepancies before I start. There didn’t seem to be any glaring ones but I just added a slight curve to the back hem so that it dipped in the same way as the front and I trued the shoulder seams so there was a smooth flow from front to back.
As I wanted to alter the front significantly I had to make some changes there first. In order to create a button-stand I simply added 2.5cms to the centre front all the way down what would have been the fold. [2.5cms was a fairly arbitrary figure because it depends really on what size buttons you’re using, a general rule of thumb is that the bigger the button the bigger the button-stand needs to be so that there’s enough overlap and the garment doesn’t end up too tight because the overlap isn’t big enough.]I was able to do this by drawing directly onto the tissue before cutting the piece out as there was enough space to do so.
If you’ve already cut a pattern that you want to add to just stick some extra paper to the centre front fold line, or trace off the whole piece again adding the extra. The original front had a facing for the neckline so now I needed to create a new facing which would neaten both the neck edge and the button-stand. To do this I simply traced off the whole of the new front opening including the neck edge and made the facing a depth of 7cms all the way down from shoulder to hem, with a smooth and gradual curve. The photo should make this clearer. The back neck needed a new facing too because the existing one took the armhole into account. Again I traced off the section I needed making it 7cms at the shoulders to match the front facing.
The final change I made was to lengthen the sleeve a little and add some more fullness to it. I started by making the sleeve 5cms longer and then I drew 3 vertical lines on the pattern at approximately the front notch, back notch and shoulder seam points. [Depending how much extra fullness you want to add to a sleeve you could use more places than this but do try to space them evenly apart.] Next I cut up each line from the bottom until I reached almost the top, I left this very slightly attached. With the piece flat on the table I spread the bottom of each slit by about the same amount, probably about 4 cms, then taped slithers of paper into each gap.
If you don’t want to cut the pattern up you can do the same process by still marking the vertical lines on then pivoting the uncut pattern at the top of each line, use a pencil or your finger as the axis. Draw or trace around the first section, which remains stationary, then each subsequent section after you pivot it to so that you get the extra fullness being added at the hem. Opening up the wedges in this way means you’re adding fullness to the hem but not the crown of the sleeve, if you want extra fullness in the crown spread the whole piece more or less parallel. The grainline should run equidistant down the centre of the new piece (unless you want to cut it on the bias)
Having done all this I cut it out and was ready to sew!
I started by joining the shoulder seams of both the blouse and the facings (which I’d interfaced and neatened) then I attached the facings to the neck edge, turned, understitched and pressed. The keyhole back calls for a small rouleau tube as a button-loop which needs to be inserted at the same time as applying the facing although you could choose to make a hand sewn thread loop and stitch that at the end. In fact it isn’t even vital that this is a functioning loop if you’ve got a front opening, the keyhole is purely decorative now.
I put the blouse onto Doris to check it was looking OK and this was when I found that the keyhole appeared to be bagging outwards quite significantly. I decided not to do anything at this point and I would check again once I had sewed the side seams and put the sleeves in, then I would get a better idea by trying it on myself.
I made three rows of shirring on the sleeves next, using my quilting guide to make sure the first row was 5cms from the bottom edge, the next two rows were then sewn parallel to the first. [Refer to a previous blog post on how to sew shirring if you haven’t done so before] Next I sewed up the sleeve seams and pin-hemmed the bottom edge to give a neat finish.
After sewing up and neatening the side seams I inserted the sleeves. At this point I tried the blouse on again to check the keyhole on myself and, with real shoulder blades under it, it didn’t seem so noticeable. Two other things struck me though, the blouse was a little too big so I took it in on the side seams and also the blouse was a bit shorter than I expected. In order to take as a small a hem as possible I made some bias binding from offcuts of the fabric then stitched it (folded in half lengthways and with the cut edges together) to the hem using a narrow 5mm seam allowance [This is a useful finish to any hem or edge where you need every spare centimetre of fabric.] Have a look at the photo which shows you how to get the ends of the binding enclosed within the front facing. I turned the binding up and top-stitched in place.
Finally, I found some ‘vintage’ buttons amongst my treasure trove and there were just the right number meaning the whole blouse had been sourced from what I already have!
Well I hope now that I’ve made it that I’ll have a chance to wear my Chelsea blouse somewhere other than in my own garden this summer, who knows? Maybe you’re reading this long after the emergency ended and life has returned to some sort of normality, although it definitely won’t be exactly as it was before.
Sewing our own clothes is an activity which gives us so much enjoyment for a variety of different reasons and, right now, the simple act of creating something is chief amongst them for me. It’s absorbing and the problem-solving gives me something else to think about.
I think the keyhole back is, by and large, just about acceptable when I’m wearing the blouse. I also think the cure could be to add a centre back seam instead of cutting on the fold so that the point of the keyhole could extend beyond the centre back line, this would hopefully bring the button and loop closer to one another when they are done up…this is just my theory based on experience and I haven’t tried it out. It’s such a nice little detail that I’m disappointed it hasn’t worked out quite right. I also regret not reading my fellow Simple Sew bloggers reviews of the blouse because then I would have known how short it comes up, personally I would add a minimum of 8-10cms to the length next time.
The sleeves are pretty and feminine but maybe they are a little too girly, the jury is out…
It’s been almost a month since I was loaned a Pfaff Coverlock 3.0 to try out so thought I would give you a ‘half-term report’ on how I’m getting on with it.
First thing to say is that it’s quite a beast! It’s a very substantial piece of machinery and so is fairly heavy as a result. That being said, this is normally the case with coverstitch machines because they are generally bigger than overlockers so the weight isn’t unusual. It does have a good-sized and comfortable carrying handle though.
Ok, so, the Coverlock 3.0 is a combination machine in that it is both an overlocker and a coverstitch machine. I’m sure you already know that an overlocker will trim and neaten raw edges and often sew the seam as well if you have 4 or 5 thread version. What you may not know is that a coverstitch machine doesn’t trim any edges, it will sew two or sometimes three rows of top-stitching on the outside of a garment whilst covering the edge of the fabric on the inside with loops of thread to ‘cover’ it. It has the advantage of being stretchy too. If you’re still not sure what I’m talking about have a look inside the hem or cuffs of a RTW jersey garment and you should see.
The first thing I had to do was not only rethread the machine as it didn’t arrive pre-threaded but I also needed to change it’s function from coverstitch to overlock. A major part of what I want to assess for you is how quick and straightforward it is to go between the functions. This is partly why I didn’t plunge in with a review as soon as I got it because I didn’t think it would be balanced or fair. Indeed, I will certainly write another review in due course after a decent amount of time and usage has occurred.
Because the machine was merely delivered to me without any demonstrations I’ve needed to use the instruction book a fair bit. If you have difficulty following written instructions and/or diagrams this may not be ideal for you but there is a (silent) DVD included with very clear animations of exactly what you need to do for each of the stitch variations possible. [I didn’t find this straightaway though so I muddled through with the booklet! I’ve also since found a few very helpful You Tube videos which were useful]
I’m not going to lie, it does take a bit of time to make the changes because you’ll need to remove and reinsert the needles to different positions as well as thread the machine in different ways depending on the function. This will eventually take me less time and I’ve added Post-it notes to the relevant pages in the book so that I don’t have to keep searching for the two I’ve favoured most. The machine is capable of up to 23 stitches using 2, 3, 4 or 5 threads and up to 3 needles. So far I’ve only used the 4-thread overlock and the coverstitch but I will endeavour to use more, including the flatlock, and report back.
I decided on making a hacked version of the Tilly and the Buttons Nora top which I’ve made a couple of times before as I didn’t want any nasty complications by attempting an unfamiliar pattern with a new piece of machinery!
The beautiful jersey with an amazing ‘tie-dye’ print is from Lamazi fabrics and was my choice as a July/August maker of the month [it could be you if you tag them on Instagram] I cut the sleeve to approximately 3/4 length and also cut two cuff pieces which were again approximate, initially about 20cms in length and then my wrist measurement at one end and my mid-forearm measurement at the other. I added a couple of centimetres for seam allowance to all sides.
I’d definitely say you need to do a bit of forward planning if you intend to use both the overlock and coverstitch functions on a project because of the swapping between the two. For example, on my Nora I needed to coverstitch just the cuffs and the hem, everything else could be sewn either directly using the 4-thread overlock or on my Quilt Ambition 2.0. I opted to sew the top together first and complete the hems at the end, in the usual way although there may be times when it’s better to hem first, we’ll see.
If you’re merely changing the thread colours it can be done in the same way as regular overlockers by snipping the threads near their spools, tying on the new colour and pulling each of them gently through, plus rethreading the eye of the needles. On one occasion when I altered the function I completely rethreaded but the stitch was much too loose-what had I done? It was all done correctly and yet it was way too loopy. I checked the manual for hints on troubleshooting but it didn’t make much difference. I was starting to pull my hair out when I realised I had threaded the machine without lifting the handle out of the way-the threads MUST go under it or they don’t sit in the tension discs! (Had I watched the helpful YouTube video first I would have known this…) Another thing I learnt the hard way was when the spool holder kept falling off the back of the machine and I was ready to chuck it out of the window I noticed it has to be slid sideways to click securely in position-doh!
The next two projects I made I didn’t use the coverstitch function as both the sweatshirts had cuffs and waistbands but I constructed much of them using the 4-thread overlock stitch. I used fabric provided to me by Minerva and they will appear on their blog in the new year. One of the patterns I used was the gorgeous Maxine sweatshirt given to me by it’s designer, Dhurata Davies. I’m going to make another one soon so I’ll write an individual blog on it then. [I got both tops out of 2.5m of fabric!]
For the final project I want to talk about here I took a different approach. It’s an Amy top by Brilliant Patterns and which I’ve made a couple of times before. I had a 1m remnant of loop-back cotton sweatshirting which I bought from Sew Me Something at a show for £8 and by shortening the sleeves very slightly, cutting the neckband in two parts and joining it I got a WHOLE sweatshirt out of the one metre!!
This time I set the machine up with a wide 2-needle coverstitch and I used my regular sewing machine to sew most of the seams. What I did at each stage of construction was to press the seams flat and top stitch them using the Coverlock. This meant that there would be two rows of top stitching on the outside and the raw edges were covered on the inside. This was generally OK although as I’ve yet to ‘get my eye in’ with lining up the foot against a seam or other visual marker a couple of them do waver more than I would usually like. It turns out there is a large removable flat bed included to increase the working area (it was tucked down inside the box and I’ve only just found it!!) this will support your work while you sew but it does take up a bit more room.
So to sum up (for now) I’ve been impressed with the quality of the stitches I’ve used so far on the Coverlock 3.0 and I will definitely look for opportunities to try others whilst I have it. I’ve yet to be convinced about swapping between the stitch-types but obviously, as I get more familiar with it, I should get faster at changing between them. There are few processes which have to be gone through to make the changes but I’ll probably work out an order or procedure to follow to speed it up. If you are short of space a combination machine might be useful, they aren’t cheap though. You’ll almost certainly use the overlocker stitches more of the time so possibly changing occasionally to coverstitch will be sufficient. I would definitely say you should have a thorough demonstration of the machine so that you know what is involved and what it is capable of. Unlike washer/driers which don’t do either job very well this machine does both functions to a very high standard.
Thank you to Pfaff for giving me the opportunity to try out their machine and if you have any questions about my experience so far then do ask.
Trend are fashion-forward indie pattern company based in London and I’ve already used their Asymmetric Dress pattern twice (and reviewed it here) I even wore the first one for the Love Sewing magazine Sew Over 50 photo shoot too because I felt it was such a striking but wearable dress that it deserved to be seen in a national sewing publication!
The next Trend pattern I’ve decided to tackle is the Frilled Hem Top TPC5 and it’s another goody as far as I’m concerned. As well as the ruffle detail it features some interesting diagonal seam lines (there’s no side seam) The degree of difficulty is described as moderate and I’d agree with that because although the techniques used aren’t difficult you need to keep your wits about you to ensure that you’re attaching the pieces to the right seams, it could be easy to lose sight of which way up they are because the usual ‘landmarks’ like armholes or necklines aren’t so obvious. There are photographs as well as written instructions, which are fairly clear, at the end of the day it’s a simple top and so long as the ruffle goes in first attached to the right pieces then adding the back yoke and sleeves is straightforward. I hadn’t got a suitable zip, I’d thought about using an exposed metal zip but the one I had in my stash was too chunky for the weight of the fabric so I opted for a simple button and hand sewn loop closure instead.
My fabric was a very thin cotton I’d picked up from a swap sometime ago-I couldn’t really say what it is as it isn’t soft like lawn, or sheer like voile, it’s slightly more crisp like poplin but less weighty. Whatever, it’s worked just fine for this and it didn’t cost me anything!
As I was making the top at this year’s Stitchroom Sewcial I was fortunate to be able to use the industrial rolled hem machine to finish the edge of the ruffle, it’s super-quick and neat and took me about 30 seconds to hem the whole piece instead of my usual pin-hem finish which would take at least half an hour!
As I didn’t have much fabric, plus I wanted to wear it as a summer top, I cut the sleeves down to short length. I was a little concerned that they looked like they may be a bit snug on my not-very-slim arms, the bicep measurement seemed to be ok but the crown looked narrow. I decided to go ahead and insert the sleeves and actually they are just fine as you can see from the photos. As there is no underarm seam to match the sleeve to it’s vital that the shoulder/sleeve head notches are marked or you’ll struggle to insert them properly. I’ve made a straight-from-the-packet size 14 again and the fit is spot on for me with no alterations, it’s a good fit across the shoulders and upper chest area and then flares out over the hips.
There are two points in the instructions which are useful and important to follow. The first is very simple, it tells you to ’sink stitch’ (that’s what it always was until ’stitch in the ditch’ became a thing) through the shoulder seams to hold the neck facings securely in position, this is both quicker and more effective than hand stitching them down I always think. The second point is that you can’t sew the whole hem up all in one go, you’ll need to sew the centre front section, stop, move the frill out of the way and then recommence the rest of the hem. If you don’t you’ll just sew over the frill which will look terrible.
So that’s the Frilled Hem Top, it should probably take around half to a whole day to make, it took me longer because I was nattering at the Sewcial quite a lot, and then I made a super-quick Mandy Boat T-shirt using the industrial coverlock machines in between too.
The TPC5 takes a little under 2 metres of fabric, probably less if you’re making it sleeveless or short sleeves. The size range isn’t extensive, 6-16 UK sizes, and they aren’t the cheapest but I’ve been very happy with the two I have and I’ll definitely make some more variations of this particular pattern. You could create some really interesting looks by using contrasting fabrics or colours, or leave out the frill completely to show off the unusual seam lines?
Trend have a wide range of patterns now, which don’t necessarily appeal to everyone but I think they are well worth a look at because of their unusual styling and details. They may look scarily fashion-forward but if you want something which is less predictable and run-of-the-mill in a sea of ‘meh’ patterns then, in my unsolicited opinion, they are a good bet. They often have a flash discount offer too so keep your eyes peeled for them!