Tilly and the Buttons Nora top

I’m very excited to have been offered a copy of one of the new Tilly and the Buttons and I jumped at the chance to try Nora, a drop shoulder jersey top with several variations of sleeve, neckline and length. It’s just the sort of top I like to wear, often layered up in colder weather so I thought you might like to know what I think about the pattern.

IMG_8487
keeping the design under wraps before the launch.

For once I decided I would trace off the pattern first because I’ll probably want to use several of the variations but this time I wanted to start with the long sleeve, uneven hem version.

Initially I checked my measurements against the sizing chart, and then the very useful finished garment measurements chart too. It’s always helpful if patterns have this (‘big 4’ patterns usually have them printed directly on one of the major pattern pieces) because you can make a much better judgement of the size you want. Take a tape measure and hold it around your body using the finished garment measurements to see how you feel about the fit-too loose? too tight? I opted to go down a size from the one indicated by my body measurements because I felt the finished top would be plenty big enough.

I had some lovely loopback sweatshirting in my stash that I’d bought from GuthrieGhani at last year’s one and only Great British Sewing Bee Live in London. It had been destined for a top based on one I’d seen at the Burberry ‘Capes’ show at the beginning of 2017 but never quite got made. When I clapped eyes on the Nora I knew the Burberry top would rise again.

fullsizeoutput_29d4
I love the varied layers and stripes of this look.

In order to match the stripes, take your time laying up the fabric ready to cut. Ensure the stripes on the underneath layer are in line with the top layer by popping a few pins through both layers every so often. Next, I placed the front and back pieces onto matching stripes at the lower edges, double checking that the bottom of the armhole was also the same. I didn’t cut the sleeves out at this time, I waited until I had the front and back sewn together at the shoulders and the neck band attached before doing this. This way you can have your actual garment laying on the fabric next to where you’re intending to place the sleeve pattern, I cut each sleeve separately to make absolutely sure.

Tilly’s instructions and photos are generally very clear and helpful in my experience. I’m not sure if I did the neck band in quite the same way as the instructions but it worked and looks good. Different knits and jerseys have differing amounts of stretch so you may need to adjust the length of the band you use. I made mine shorter in the end as it wasn’t sitting flat at first, the band needed to be more stretched onto the neck edge to sit nice and flat.

IMG_8602
I’ll take that!

The beauty of the sleeve on the Nora is that it’s a ‘shirt sleeve head’ so it’s almost flat across the top. This means it’s very simple to sew on because there’s no tricky setting into an armhole to do, you sew it on flat and then join the underarm and side seams afterwards. Incidentally, I sewed most seams using the tricot stretch stitch (looks like lightening in the symbols if you’re looking for it on your machine) You could also use a zigzag that’s very flattened out by reducing the stitch width. Alternatively, you could sew most of Nora together using an overlocker but don’t forget the seam allowances are 1.5cms and an overlocker will be much narrower which could result in a bigger garment than planned if you don’t trim them down first.

Before I hemmed the sleeves I tried the top on and opted to bring the sleeve width at the cuffs in by a total of 6cms [only as far as the elbow though from where I graded back into the original seam] Although the cuffs were a bit too wide for my liking I loved the extended length which comes some way over your hands.

That just leaves the stepped hem. I used a twin needle to sew straight across the hems and a regular ballpoint needle to turn the side seams.

Before I started Nora I’d already decided that I’d wear a shirt under the stripy version because the front is actually a bit higher than I like so, when I make my next one, I’ll lengthen the front somewhat but still keep a ’step’. I’ve been wearing it with my favourite The Maker’s Atelier Holiday Shirt underneath and I love how it looks together. I bought some beautiful Liberty fleece-back sweatshirt fabric from Fabrics Galore at the recent Knitting & Stitching show which I’ll use to make the Nora with the high roll collar instead and the long cuffs will roll back to show the contrast colour, it’s going to be so cosy. I reckon you could make it in a drapey woven fabric too BUT  you’d have to make the neckline larger because you wouldn’t get your head through otherwise!!

fullsizeoutput_29acIMG_8591fullsizeoutput_29bb

IMG_8563
No make up selfie in Threadquarters! I really like all the hem interest going on.

Thank you Tilly for the chance to try out Nora, I’m definitely a fan and I think there will certainly be a few versions of her finding their way into my wardrobe over the autumn and winter…and then there will be short-sleeve versions when the spring arrives!

Until next time,

Happy sewing

Sue