I seem to be constantly attracted to teal/turquoise/duck egg shades recently so this Art Gallery organic cotton jersey for my recent Minerva post looked perfect when it hoved into my field of vision!
I’ve used Art Gallery knit fabrics in the past and the designs and fabric, whilst fairly pricey, are lovely quality. This particular jersey is an organic cotton (with a little Elastane) and very soft, a lighter weight than many so it would be good for children’s and babies clothing as well as adults. I love the print, I think it’s a vaguely ‘Tribal-esque’ graphic stripe and I quickly decided to make a Tabitha T-shirt from Tilly and the Buttons book ‘Make it Simple’ which I’ve made a few times before but to try out the dress hack version for a change this time.
I traced off a new copy of the pattern using the horizontal lines indicated across the bodice specifically for the dress. I’m not long in the body but I thought it looked a little short so I added an extra 2cms to the bodice length. In truth I probably could have added more than that because I feel there isn’t as much blousing at the waist as there seems to be in the photo in the book [If you know, or suspect, you have a long body length then pay close attention to this before cutting your fabric, get someone to take your nape to waist measurement and compare it to the back pattern piece. If necessary then add any extra through the horizontal ‘lengthen/shorten’ lines, and don’t forget to do the front as well!] If you’re wondering why this matters, it will mean that the waist seam sits too high above your natural waist and could look more like Empire line.
I followed the instructions in the book to draft my own skirt pattern which was simple enough, you only need one because the front and back are identical (you’ll need a decent sized piece of paper to do this) I cut the new front and back as complete pieces so that I didn’t have to cut anything on the fold, I also wanted a short sleeve so I traced one off.
The fabric was a little bit curly at the edges so I took my time cutting out, be careful not to pull or drag the fabric at this stage because this could result in twisting of the finished garment. It’s helpful to mark stripes onto the pattern so that you can then match them to corresponding seams more easily. Cutting a single layer of fabric can really help make this more straightforward, and be less wasteful too.
Moving on, the suggestion for the waist casing is to use eyelets or buttonholes. I used a small round-ended buttonhole, whichever method you choose make sure you interface underneath first to stabilise the fabric. I used the quilting guide to help me sew an accurate 2cms seam to create casing. Once I’d sewn it I used a bodkin to thread the ribbon through.
The rest of the construction was pretty quick because I already knew the T-shirt in size 5 was a nice fit, the skirt was a bit ‘hippy’ though so I took some off in that area. Following the drafting instructions the pattern piece is shaped for the waist but, for me, a straight rectangle would suffice.
The length was educated guesswork but I’m very happy with it and it’s not too restrictive at the hem, any longer or narrower and the skirt might need a split in it to allow movement. I have the advantage of using a Pfaff coverstitch machine to hem the sleeves and skirt but a twin needle or a zig-zag stitch will do the job too, and don’t forget to use a ballpoint or jersey needle. I used a narrow grosgrain ribbon in a toning teal to slot through the waist casing to complete the dress. As I mentioned near the beginning I might add just a little more length to the bodice next time but otherwise I’m really pleased with this Tabitha dress, it will be comfortable to wear for everyday and easy to roll up in a suitcase if I ever get to go on holiday again!
Minerva provided me with this lovely fabric to write about, I’m delighted with the quality and I’m especially happy with the dress which is so just comfortable.
I followed the progress of this pattern with interest on Instagram when it was originally released nearly two years, it was fascinating to see how Claire-Louise Hardie (the Thrifty Stitcher!) developed and finessed the various elements of it as she sampled it, up to the point that she was ready to release it for sale. It has attractive style lines with princess seams in the front which curve into hip pockets, the back also has princess seams and there’s a horizontal seam just below the natural waist. The collar curves up smoothly against the neck and the back collar has a ‘sunray’ of five darts spreading out towards the shoulder blades which I particularly like. The cuffs each have 3 similar darts, the details on this pattern has simple but so stylish.
This post was originally published last year by Minerva who generously provided me with a nice firm Ponte Roma in a plain navy to make the Dawson in, it would also work very well in a boiled wool, felted wool, Melton, not a loose tweed though as they can start to fray and you’d lose the details too much in the weave. Anything fairly structured and stable would effectively show off the style lines. You could get some interesting effects with checks or stripes if you want a challenge! I’d wanted to make another version for a while because I’ve had really good use from the navy one, I hadn’t got around to finding any specific fabric for it but then I hit upon the idea of using a single old heavyweight cotton curtain that used to keep the drafts out by our front door. It had long been replaced for this task but I just had it folded up underneath the heat-reflective mat that I use on my cutting table. In order to maximise the fabric in the curtain I undid the deep hem and the sides, and removed the tabs at the top. I gave it a wash to clean it but also to, hopefully, stop it shrinking later on.
Areas like the pocket edges and the neck need stabilising with some iron-on tape or strips of interfacing as per the instructions, especially if you use a knit fabric like Ponte. I would recommend stabilising the shoulders with seam tape or scraps of ribbon to prevent stretching too. I used a specific needle for stretch fabrics and you could use the ‘lightening’ stitch to sew with if your machine has it, or a very straightened out zigzag. If you do use boiled wool the layers could be quite thick, use a straight stitch but you may need to lengthen it a little more than usual.
The pattern comes in eight sizes which are not numbered in the conventional way, CL opts for letters instead, so you work from your own body measurements to choose which size should fit you. I cut and sewed a size F originally which was quite generous, for the newer version I’ve cut the next size down. I misjudged how generous the ease is in the garment so I usually wear the Ponte version layered up over jumpers or sweaters on warmer cool days if that makes sense. At the end of the day it’s intended as a casual coat so don’t make it too small as you’ll always be pulling it closed across you. The sleeves are nice and roomy too, I’ve noticed some coat/jacket patterns can be a bit snug around the bicep for me which is a bit dispiriting, I’m hardly a muscle-bound hulk! Just check before cutting out if you’re happy with the sleeve length too, I probably could have added just 3-4cms because it feels the tiniest bit short on me.
The pattern goes together beautifully and all that tweaking in the sampling stage is borne out in the final version. I found the instructions pretty clear, they are mostly photographs and there are some really useful hints and tips which will come in very handy if you aren’t that experienced in your dressmaking yet. Make sure you transfer your markings for the pocket pivot point for example so that you get a crisp finish for the corners.
You could top stitch all the darts down, possibly in a contrast thread if you like, but because the Ponte had a slight stretch I didn’t do this on mine. I did top stitch down the front facings though and caught them down in a couple of places on the inside to stop them flapping.
For the ochre version I topstitched more of the seams, I confess that I was incredibly slovenly and used up various threads in my collection so not all the stitching is the same colour…oops! Incidentally I didn’t use top stitch thread, instead I used the triple straight stitch which looks very similar although it is quite thread-hungry (hence the non-matching!)
This time however I didn’t top stitch the front facings down, I adopted a different approach. As it’s an unlined coat so all the innards are visible I used some ribbon to anchor the facing down in a couple of places. I chose to do this because I know from experience that when you’re sewing through several thick layers the triple stitch (which is a set length on my Pfaff and not adjustable) it can lead to puckering which doesn’t look so nice. Try a sample before you go ahead if you aren’t sure, that’s a LOT of slow unpicking if you don’t like it after all.
I finished the hem by hand using a herringbone stitch rather than machining it for the same reason that I didn’t top stitch the front facings.
I think the Dawson is a well-drafted and executed pattern from an independent designer (and CL’s art work features herself so it squeaks into the #so50visible category!) The Minerva Ponte Roma works well for the soft tailoring, using my old curtain gives the slightly cocoon-shape a little more definition. It shouldn’t be too difficult to do an FBA if you need to either. I’m much happier with the fit of the ochre one, but I love the navy and will still wear it regularly too.
Because the Dawson is a loose cocoon shape it would make a beautiful evening coat in a glamorous brocade, to go over the top of your evening outfit, denim would look great too (Have a look at my Simple Sew Cocoon jacket in denim here)
I guess this was also a useful exercise in upcycling, the curtain was years old and not being used for it’s original purpose so I thought why not give this a try. If I found I wasn’t mad about wearing the colour after all I know it’s 100% cotton so it would dye, I might come unstuck with the polyester sewing thread though which would take up the colour differently-it’s hardly Saville Row standard though! The Dawson took barely two metres of fabric (the front facing is helpfully cut in two parts which helps reduce the fabric usage, and of course you could always use a contrast fabric anyway) it doesn’t instruct you to use interfacing on any of the collar or facing parts but I did, just to stabilise the fabric a bit.
I originally wrote this as a review for the MinervaDotCom blog but I’m not actually sure if it ever appeared. Rather than waste my efforts I thought I’d publish what I wrote here instead.
I’m sure it was a combination of an over-generous stated fabric requirement, my just-to-be-on-the-safe-side ordering and then super-stingy cutting out means that I managed to get not one but TWO sweatshirts out of my Minerva fabric choice this time. At the time of writing last autumn, Minerva were introducing a collection of textured jerseys made in a polyester/ viscose/ spandex mixture which came in a wide range of colours and textures so I opted for a geometric design in lilac to try out. I would suggest that this fabric is not as firm or thick as some jerseys suitable for sweatshirts, it isn’t fleecy on the reverse for example but it has reasonable drape, is soft to the touch and has a fair amount of stretch but not in a ‘really difficult to control’ kind-of way (it isn’t like lightweight jersey for T-shirts for example) it’s actually pretty stable so manipulates well into armholes or cuffs.
I already had a pattern I wanted to try, the Maxine sweatshirt by Dhurata Davies that has interesting diagonal seams across the front which have pockets in them. This actually made cutting out a whole lot more tricky than I anticipated because the ‘check’ design of the fabric I had picked turned out not to be square but rectangular so matching the lines was a real challenge. In some areas I’ve failed so my advice would be “don’t choose a pattern that has too many intersecting seams or style lines” because you could end up tearing your hair out when you can’t get it to match! Once I’d committed though I decided to press ahead and settle for ‘almost but not quite’…not my usual route but there we are.
When it became apparent that by folding and cutting really carefully I’d have oodles of fabric left over I pulled out a very simple sweatshirt pattern Simplicity 8529 and cut that at the same time. You might recognise this pattern as the Toaster sweater by SewHouseSeven if you think it looks familiar. If you fold the selvedges in towards the centre so that you have two folds then it’s often possible to get more pieces out of less fabric, any sleeves, yokes or facings can be cut out of what remains.
I currently have a Pfaff Coverlock 3 on loan to me so I used it to sew up much of the two tops on it’s 4-thread overlocker setting but you can easily sew this fabric on a regular machine, just use a ballpoint or stretch needle and set your machine to a very elongated zigzag if you can (regular stitch length and a narrow width) or a ‘lightening’ stitch if your machine has it. Unlike some jerseys or sweatshirting you’ll definitely need to neaten the seams though because I found the fabric frayed and went fluffy at the cut edges quite badly as a result of the woven nature of the surface design. Use a zigzag stitch on the edges if you have limited options, or pinking shears.
The ‘Maxine’ is a great design which stands out in a crowded field of many other sweatshirts and the well-written instructions and diagrams are very clear and simple to follow. The tricky area could be the point at the centre where the seams intersect, I simply made this more complicated for myself by choosing the geometric design! And of course it has pockets! I’ve made another version of it since the lilac from a remnant of linen/wool which you can read about here.
The Simplicity/Sew House Seven pattern has a very simple ‘grown-on’ collar and self bands on the cuffs and hem. I cut and made this one up in less than two hours and it shows off the textured surface of the fabric very well.
I would suggest that this fabric will make very comfortable loungewear like track pants, tees, sweatshirts, dresses and children’s wear. I don’t know what the other designs in the range are like but if you are pattern match averse then this particular one might not be for you! I thought at the time it would be interesting to see how well a fabric with a raised surface texture like this wears and now that several months have elapsed I’ve found that it catches quite often and has started to pill quite significantly which is disappointing given the price per metre.
My thanks to Minerva for providing me with the fabric to write about, this is a significantly different version of the blog post which may, or may not, have appeared on their website. I did try to find it but their search function doesn’t make it very easy to find specific posts.
My latest Minerva blog post is up for you to read now and it’s a jacket that nearly didn’t make it. I chose the fabric based on the image on screen but when it arrived both the background colour wasn’t what I expected and the design was larger than I thought it would be too. The lesson to learn from this is to order a swatch whenever possible to make sure the fabric is exactly as you expect or want.
That said, the quality of the loop-back jersey I used was absolutely lovely and it made up-eventually-into a really nice Jalie Charlie bomber jacket. I haven’t used Jalie before but I must say I was very impressed with the HUGE size range each pattern comes in, the quality of the instructions and illustrations (in both English and French) and the sizing is spot on.
The next problem I had was matching ribbing to the multi-coloured fabric and also finding a suitable open-ended zip. Eventually I found a gorgeous raspberry pink plain jersey from Sewisfaction instead of ribbing, and I got a zip from MacCulloch & Wallis in London.
Anyway, once I got everything together it all sewed up really well and I was pleased with how all the colours eventually came to form a unified whole. Subtle it isn’t so it definitely needs to be worn with plain garments but it’s a bit of fun and I know I’ll use the pattern again too.
As always, you can find the full rundown of my making experience over on the Minerva blog now, I hope you find it useful.
How often do you alter or adapt a pattern when you’re making it? By that I don’t mean the usual things like adjusting the fit to suit your height or bust measurement, I mean really alter it significantly with things like changing the sleeves or completely changing the length.
I’ve always enjoyed doing exactly this because it’s a way of making a garment completely original and all your own even if loads of other dressmakers are sewing and sharing their versions of a particular pattern. These days this process even has it’s own name-pattern hacking. You can read a couple of my previous blog posts where I’ve hacked patterns to give you some other ideas, here and here.
When I was invited by The Fold Line to take part in the Simplicity Patterns/Eve Appeal campaign this year I knew it would be something I’d enjoy and could really get my teeth into. There are a range of patterns you can choose from and for every one sold Simplicity will make a donation to the Eve Appeal. I picked a blouse pattern #8658 to use because I could see its potential for changes, not least because it’s shown in stripes on the envelope and I knew there was fun to be had playing with the directions of them. I chose a really lovely blue striped shirting with a little bit of stretch generously provided by Minerva and while I waited for it to arrive I did some sketching of ideas. The raglan sleeve is in two parts running down the top of the arm to the wrist so my first idea was to have the stripes running in different directions, which led on to having the lower, bell-shaped part of the sleeve cut on the bias.
I thought the back needed to be a bit more interesting than just a centre back seam with a button and loop closure so I altered it to include buttons and buttonholes. The blouse is over-the-head anyway so I don’t need to be able to open the buttons to get it on. The neckline is finished with bias binding but why put it on the inside when you can make a feature of it on the outside?
Strangely I never saw it as staying just a blouse, it was always going to become a dress but how to do that? I like long floaty skirts so I sketched out quite a few variations of gathered, pleated and flounced skirts, all with pockets in the seams somewhere. I had decided that the bodice should be higher at the front than the back which obviously would affect the skirt levels but I eventually left that decision until the bodice was made up and I could see it more clearly on the stand.
I thought I’d do some of my initial adaptations and make it up as a blouse first to check the fit. The back is easy to change because it already has a CB seam so I merely added 5cms to the edge to allow for a grown-on button-stand. The original stitching line will remain as the CB and that is where the buttons and buttonholes will get positioned. I traced all the pattern pieces I needed onto spot-and-cross paper although the envelope does include a large sheet of squared tissue paper for you to use to make your own changes if you don’t have spot-and-cross. [You could use cheap wide greaseproof paper if you have it, I used to use broadsheet newspaper taped together when I was a student but that’s getting harder to find!]
Having traced the two parts of the sleeve once I then retraced them again (I didn’t want to cut up the first ones, I may want the sleeve full-length at some point) just the top parts to a length a bit above my elbow, around bicep level, not forgetting to add seam allowance to the new lower edge. Next I pinned the FULL-LENGTH sleeve pieces together along the stitching lines vertically so that I could trace off a new single piece for the lower sleeve. As well as the regular straight grain I added a bias grainline too because I’d be using that with the stripes. You could add extra fullness to this part by cutting and spreadingif you wish, it would make a very voluminous bell-shaped sleeve.
I cut a size ‘medium’ according to both my body measurements and by referring to the finished garment measurements printed on the pattern. Using some lovely printed poplin from Stitch and Knit, a new fabric and yarn shop near me, I made up the blouse. Part of my plan on the dress was to highlight the seaming with topstitching so I did this on the blouse too although I used a fun ‘circles’ stitch in a contrast colour which echoed the design on the fabric. I didn’t cut the lower sleeve on the bias though because it wouldn’t make any obvious difference to the look of the print. I tried out my idea of French binding on the outside of the neck edge and that looked good too.
Overall I was very happy with the fit of the medium so I didn’t need to make any changes to sizing. This meant I could retrace the front and back bodices to my chosen length which was approximately Empire-line or a few centimetres below my under-bust line. To decide where this was first I pinned the front and back parts together at the side seam on the stitching line and then attached it all to the stand. You can then see more clearly where you might want to draw the horizontal style lines from front to back, especially if you want a sloping line. With these lines drawn on you can trace off the new, shorter parts and check them on the stand and on yourself too. This is important because I thought I’d made the line a little too high so I added some more length to the bottom, 5cms in all I think.
This might all seem like a lot of tracing off and you could just indicate on the pieces where your various cutting lines are (or wing it!) then transfer your markings direct to the fabric. As I planned to rotate the back so that the stripes were horizontal I wanted accurate pattern pieces.
After cutting the bodice section in striped fabric I first reinforced the buttonstands with iron-on interfacing up to the fold line. Next I attached the appropriate sleeve parts and top stitched the seams, then joined the shoulder seams so that I could bind the neckline. I’d cut a long bias strip of fabric 5cms wide which I folded lengthwise wrong sides together and pressed to get a crisp edge. Next place the bias on the WRONG SIDE of the fabric with its folded edges to the cut neck edge, this is because you will flip the binding to the outside eventually where it will be visible. Once you have pinned the binding in place you will know exactly how long it needs to be so then you’ll need to neaten the ends by turning them RS together and stitching. Fold them back out and pin in place, it should be level with edges of the buttonstands. Stitch the binding in place using a 1cm seam allowance, trim and snip as required then flip it to the right side and topstitch in position around the neck. The photos of the blouse version should make this clearer.
You can sew the buttonholes at this stage too if you like or leave them until the end. I’d bought the most gorgeous metal buttons from Duttons for Buttons in Harrogate, Yorkshire, the only problem was that the loop on the reverse of them isn’t central which is why the top button looks a bit off kilter, it had to be sewn like that so that the top band remained level.
I attached the lower bias-cut sleeve parts next, sewed up the side seams and elasticated the cuffs., as per the instructions (yes I did use them occasionally!)
I still couldn’t decide what to do with the skirt so I tried a couple of ideas out with fabric scraps to mock-up various looks. The shirting is quite fine so it gathers really nicely without a lot of bulk, if I’d used pleats I would have had the complicated task of working out the pattern pieces to fit accurately onto a curved and dipping lower bodice edge and that was a challenge too far-especially as the stripes would have had to match too!
Eventually I settled on a bit of a technical cop-out by using two simple rectangles which gathered onto the lower edge of the bodice instead of making shaped skirt pieces, apart from the central areas where they would be flat. This meant that the hem followed the same line as the bodice, higher at the front than the back, but the side seams will pitch slightly forwards as a result. It isn’t the end of the world but rather that than make the dress too complicated for you to try copying for yourself. And of course I put pockets into the side seams, with the stripes running on the opposite grain. I have a cardboard template for the pockets which I made ages ago and I just draw around it directly onto the fabric as required. (Basically I drew around my hand onto card, plus a bit of extra space, plus a seam allowance and a straight edge on one side to sew to seams)
One final twist I added at the end was to insert elastic around the hem to give it an unusual silhouette. I turned up the hem 5mm and pressed it in position then I pressed it up again by 2.5cms. I topstitched top and bottom leaving a small gap through which I inserted 2cm wide elastic about 1 metre long. The casing could double as the hem if I choose to take the elastic out in the future.
Mr Y and I went to Kew Gardens on a beautiful day in September and I took the opportunity to pop into the ‘Ladies’ and change into my dress for a photoshoot with more interesting backdrops than my back garden!
I hope this has given you a few ideas that you could try for yourself, this pattern is an ideal blank canvas and it has a few suggestions included which you could try first of all. There are so many possibilities you could attempt, and some of the other bloggers involved may have used this pattern too so it will be interesting to compare their own takes on it. I wanted to mess about with stripe direction, this would also work if your fabric has a strong one-way design. You could highlight the seams using piping, ribbon or other trims, what about an exposed zip down the back? you could leave the seam on the top of the sleeves open and secure it at intervals with little buttons? Obviously you don’t have to turn it into a dress but you could play with the length or put straight horizontal seams across, maybe at different levels to each other? It could potentially be a scrap-buster too…so many possibilities! If you’re going to add style lines which aren’t already there don’t forget to add seam allowance to the edges of them, include a notch or two if necessary so that you know which pieces you’re matching together.
You might have tried and trusted patterns at home which would be ideal springboards to new ideas, or by buying this pattern you will be helping raise valuable funds for research and support of those suffering with female gynaecological cancers.
Whatever you decide to try, enjoy the exploring the possibilities, don’t use expensive fabric to start with if you’re not sure you’ll like the result, look in your workbox to see what trims and embellishments you could use, contrast top stitching is one of my favourite, and most simple, ways of making something unique. There’s a whole series of other bloggers who will be taking part in this challenge in the coming weeks and months so why not take a look at what winner of the Great British Sewing Bee 2018, and pattern-hacking queen, Juliet has done for starters, or Abi of @whatabimakes and Rachel @thefoldline have added their spin to patterns in the range now too.
You can find further information about the patterns used here too
I’m really happy with this make, it’s the Dawson Coatigan by The Thrifty Stitcher, Claire-Louise Hardie, which I made in Navy Ponte Roma given to me by Minerva Crafts in return for an honest review.
This pattern was released just before Christmas and I think it would be a useful addition to any wardrobe. It’s a softly tailored edge to edge coat with flattering seam lines and integral pockets. It works well in a structured jersey like Ponte Roma, and it would also look good in boiled wool or felted wool.
And depending when you’re reading this the Dawson also qualifies for the Sew Over 50 #so50Visible challenge too which finishes on March 15th. Read my previous blog posts for all the details on that but you haven’t got long if you hope to win one of the prizes!
There’s lots more details and photos of my make over on the Minerva Crafts website, thank you as always to them for providing me with the fabric.
My latest Minerva blog is live now and it’s all about their beautiful printed velour. I was attracted to the gorgeous mixture of teal colours with a splash of pink thrown in for good measure. Initially I was going to make a pleated skirt with it but eventually I decided that wouldn’t be flattering on me so I settled on the River dress by Megan Nielsen with my own adaptations instead.
I lengthened the short sleeves and added elastic to make cuffs, I increased the length of the dress overall too and left a side split and finally I put wide elastic under the bust to create an Empire line.
This is a very simple pattern to sew and has the novelty of two necklines-a scoop and a V-and because of its raglan sleeves you can have either in the front, I generally wear it with the V in the front.
As always, you can find the full details of the fabric and my sewing tips on adapting the pattern with a lot more photos on the Minerva Crafts website, thank you to them for providing me with the fabric, in return for an honest review.
I thought in this blog I’d take a look back at some of the things I’ve been up to over the last twelve months and it’s made me realise what a wonderful varied collection they are. As well as sewing multiple garments from numerous patterns (which I’ll look at in a separate blog) there have been several meet-ups including the Stitchroom Sewcial in June and the now-famous Sewing Weekender in August, plus one I organised myself in November. I’ve visited quite a few exhibitions, some of them more than once, read lots of books and written reviews of several of them in case anyone out there was interested in knowing more if they fancy a visit or a read for themselves. I’ve been back to the Knitting & Stitching show, and The Handmade Fair for the first time too.
In January I made my first coat in decades, the Butterick 6423 and was pretty pleased with the outcome overall.
My first meet-up of the year in February was a return visit to Balenciaga at the V&A organised by Alex (Sewrendipity) where I met a number of lovely fellow dressmakers in the flesh for the first time. It was so nice to go to an exhibition with like-minded people and then we all went for lunch together afterwards-very civilised!
Also in February Gabby Young invited me to become one of the Simple Sew bloggers so I embarked on a year of wrangling their patterns into submission, they are nice designs but aren’t always faultlessly accurate in their drafting or instructions. I took on the role on the understanding that I’d be honest (although never rude) but informative and constructive. I’ll leave you to be the judge of whether I achieved that.
I had the opportunity to visit the Fashion Technology Academy in April which was such an inspiring place. You can study many of the technical aspects of clothing production there and we also had the chance to try out a taster session of TR pattern cutting with the supremely gifted Claudette Joseph while we were there too. If you, or someone you know, wants to go down the technical route into garment manufacture then this place in North London could be a good place to start looking.
Also in April I returned to the Fashion and Textiles Museum in Bermondsey, London to attend their fascinating ‘Inside couture’ afternoon. I’ve been once before but it’s so enjoyable, and such a treat to get the your hands on real couture clothes (with white gloves on, natch). I highly recommend a visit if you’re in London but you do need to book for these particular events, the museum itself is open most days.
The first London Stitchers meet-up was held at the beginning of May and although I’m not technically ‘London’, as has become obvious, I go up a lot. These are organised by Ana Cocowawacrafts and Georgia One Stitch Forward and they vary in their locations between north, south and central London. Anyone is welcome and it’s a great way to meet new people and know that you all have at least one shared interest! It’s like speed-dating for dressmakers!!
Me Made May was also happening on Instagram and for the first time in ages I managed to post every single day for a month-long challenge even though I was out of the country for some of it. Lots of garments I shared weren’t new and box-fresh, in fact quite a few of them were old favourites, which is as it should be. We made a trip to Assisi in Italy during this time so that made my backdrops a bit more interesting for a few days!
I tried something a bit different in May by going on a course to learn how to make and print my own etchings. I’d done this once a million years ago when I did my Foundation Course at college and have always found the medium fascinating and beautiful. [Go and check out Rembrandt’s work in particular if you aren’t sure what they are] I’d met a lovely lady called Chrissy Norman on the first Sewing Weekender two years ago and it turns out that not only does she sew and knit, she’s a super-talented printmaker too. She has a separate IG account for her prints and I admired a print she posted on it early in the year. It transpires that she teaches courses a few times a year at Sudbourne Park Printmakers workshops. Long story short, I signed up and joined her in Suffolk in mid-May. It was soooo interesting and fun, plus I made some pretty respectable prints based on a photo I had taken of the Maggi Hambling sculpture on the beach at Aldeburgh, Suffolk.
The summer saw the first of several visits to the Frida Kahlo exhibition and Fashioned from Nature at the V&A museum. I also loved the retrospective of the work of Azzedine Alaia at the Design Museum, I didn’t write a review though because by the time I went there wasn’t much left of the run sadly. It was spectacular though and I’m very glad I made the effort. That same day we went to see the musical Hamilton which was absolutely stupendous, Mr Y normally doesn’t go for that style of music but even he has raved about it ever since-highly recommended!
In June I was one of the lucky attendees of the first Stitchroom Sewcial event organised by Anne ‘New Vintage Sewing’ and Lucy ‘Sew Essential’ at Anne’s workplace in the University of Loughborough. They had excelled themselves with activities for us all to try including visiting the print and weaving workshops, computerised machine embroidery, an individual photoshoot AND time to sew and use the industrial machines Anne has in her classroom. I really hope I’m lucky enough to go again in 2019…
I took a road trip with my ‘local’ sewing friends Alana and Helen to visit Sewisfaction on their first Big Summer Stitch-up which was great fun, even though it was a steaming hot day.
At the end of July and beginning of August I posted two blogs which seemed to light the blue touch paper that rapidly became Sew Over 50. When I wrote them I thought no one would read them, much less agree with me, so I was stunned by the response to say the least. My now-friend Judith was amongst those who read them and was feeling the same way so she went one step further and created a new Instagram account called @SewOver50 and everything went a bit nuts from there on. As I write this post the account has gained over 5,300 followers since mid-August which is phenomenal. It’s become a place of inspiration and encouragement for thousands of women (and the occasional man) who sew but felt they, we, are being overlooked or dismissed by the burgeoning home-dressmaking market because of our age.
One thing that some people misunderstood about the whole idea wasn’t that we wanted to be separate from any other age group, like some kind of exclusive club, not at all, we just felt that some people-magazines, pattern companies-were overlooking the opportunity to tap into a market and a group who had cash to spend, had styling ideas, skills and experience to share, originality, fun, empathy, quirkiness, style. For a lot of the people who started following the account they had very little experience of using social media to broaden their horizons in sewing terms, and for connecting with like-minded people around the world, including Australia, New Zealand, Canada and the US, as well as Europe. Suddenly there was an identifiable hashtag to follow which took you straight to the heart of this community. In fact it isn’t only sewing that members are supportive with, many face health challenges, a changing body with the menopause, dealing with elderly parents or caring for grandchildren so there have already been lots of conversations that have strayed away from sewing completely, and that’s OK too.
It’s been gratifying to see that a number of sources are making a big effort to be more diverse in who they feature in articles or as models. There is still a long way to go though because we’re conscious it might appear that it’s mostly white middle-aged women who sew, but we know this isn’t the case because there are many women of colour who sew too, maybe they don’t engage as much with Instagram or other social media though? I don’t know the answer to this one except to say that all are welcome because that’s the whole point. It makes me very happy when much younger dressmakers comment to me that they also follow us to get inspiration and advice, which is also the reason that I follow younger sewers myself!
Onwards, there was another amazing Sewing Weekender in August which was quickly followed by SewPhotoHop on Instagram in September organised by Rachel ‘House of Pinheiro‘. I didn’t keep up with this one so much and dipped in and out a bit [the same happened with Sewvember as well] but it’s a good way to find new people to follow and be inspired by if all this is new to you. I’ve just remembered there was MIYMarch (Make it Yourself) but that passed me by completely this year.
In September I became a Minerva Crafts blogger so I’m provided with fabric by them to make up into my own choice of garment and then write a comprehensive review for their own website. I’m enjoying this and it’s another string to my bow.
October saw me return to Birmingham for the SewBrum event which is magnificently organised by Charlotte ‘English Girl at Home’. It’s a chance for dressmakers from all over the place to come together in Birmingham, shop for fabric, visit Guthrie & Ghani and generally hang out together.
I was really chuffed to be invited by Amy Thomas, editor of Love Sewing magazine to contribute an article about the Fashioned from Nature exhibition to the magazine in November. It was a really big deal for me to write something specifically to appear in print. I’ve been lucky enough to write pattern reviews for Love Sewing and Sew Now in the past but this was a new departure. I’d love to do more like this in the future. There’s definitely a little something coming up early in the new year but I can’t talk about that yet…..
I organised my own meet-up at Walthamstow Market in east London in mid-November which fortunately was a beautiful day as it was well attended and we nearly all went for lunch afterwards, to continue chatting! It was the first meet-up for quite a number of the attendees but I think everyone enjoyed themselves and were delighted to get the chance to chat together in real life and not just in a comments box!
There was a lovely pre-Christmas sewing day in Cambridge called SewCam organised by Jen Walker ‘The Gingerthread Girl’ which was a delightful antidote to festive fever, and a final London Stitcher’s meet up the following weekend to round everything off nicely!
When I look back at everything in this way it makes me so happy to realise the sheer quantity of wonderful opportunities that my love of dressmaking has brought me this year in particular. I continue to teach my lovely group of ladies locally-they think all this Instagram nonsense is ridiculous in a good way! I’ve met so many awesome and inspiring women in real life for the first time and I’ve deepened some of the friendships that started last year, or longer, ago. Many people think that ‘friends’ on Insta aren’t real but that just isn’t true. Of course there are those people you should give a wide berth to and we are continually plagued by nut-jobs who think women who sew will be interested in their guns, or love of God, or whatever but if we all continue to report them then so much the better.
Wherever you are in your sewing ‘journey’ I hope you find it relaxing, fulfilling, inspiring, empowering, distracting, whatever you need it to be. I’ll never stop learning and being creative is so good for us ( we knew this all along but science is finally realising it too!)
I’ve already got some ideas for next year but, to be honest, much of 2018 just unfolded one thing at a time without too much planning in advance. I’d like to expand my own skills in 2019 and not necessarily in dressmaking terms, I have always enjoyed art so perhaps I should get my pencils and paints back out again.
There’s always an element of me hoping you enjoy what I write and find the reviews helpful or informative although, in truth, I’d write them anyway as a record. Thank you for joining me on the journey and Happy New Year, and here’s to lots more sewing adventures, maybe we’ll meet ‘in real life’ in 2019?!
My latest Minerva blog post is on their website from today and it’s a bit different from the others. This time I used a soft and fluid jersey to make a dress for my younger daughter Katie, not me.
In the post I explain how I wanted to use a single pattern [Simplicity 8602] which, ultimately, I’ll adapt for 3 of us in my family-24 year old Katie, my 84 year old Mum, and me. The first two are done, the version for me probably won’t happen for a while yet though.
Katie made life a bit difficult for me by wanting the blouse lengthened into a dress, plus altering the sleeves AND the neckline. I’ve written up all the details in the post if you’re interested in finding out how I did it.
I hope you find the post helpful and you can read it here.