Fantail follow-up!

I published my review of The Sewing Revival Fantail top recently and since then I’ve made a second using an alternative finish which I thought I would share with you.

the first Fantail top

This second version uses a ribbing finish on the neck, cuffs and back hem instead of hemming or elastication. I’d bought some Art Gallery viscose from Sew Me Something with an interesting graphic design and then my fellow @SewOver50er Kate @stitchmeayear generously offered me some grey ribbing, she had more than she needed. It turned out to be the perfect match and I couldn’t have planned it better if I tried.

There are separate pattern pieces for the ribbing cuffs, neck and hem and, although the same front, back and sleeve pieces are used, there are very slightly different cutting lines for the sleeve.

I had bought 1.5m of the graphic print and it has a fairly distinct one-way design which meant I needed to place each pattern piece carefully to try and get a reasonable match whilst not wasting too much fabric. I was able to do this by folding over one selvedge by just enough to position the front and back pieces along the same fold. This left a good sized piece from which I could individually position and cut a pair of sleeves whilst still just about getting a good match.

Sewing the Fantail with ribbing is very slightly different to the woven version. First, the deep ribbing band is sewn on the back in place of the narrow hem [I’m not sure if there’s a small discrepancy in the pattern or my cutting out but on both my versions I’ve found there to be about 5mm too much fabric in the back compared to the front when joining the side seams]

Like the first version I sewed the ribbing band onto the neck after joining the raglan seams and before sewing up the side seams. As I probably explained in the previous post, I always find it’s easier to put a facing, binding or whatever neck finish on whilst everything can still be laid out flat unless there’s a technical construction reason for doing it later.

The main reason for writing this second post is because I want to show you the way I turned the band at the hem-I forgot to take photos as I was making the first one! It’s a really neat way of of finishing the bottoms of the side seams and can be a useful technique in other places when you’re sewing different hems or edges together because it gives a crisp and level finish to an edge with the seams enclosed. The photos will help make more sense.

Pin the side seams together like so first, the raw edge of the deep elastic casing for the front is already pressed up by 1cm and the bottom of the ribbing is lined up against the notch for the casing.
Next, fold up the front so that it sandwiches the ribbing like this, pin in place. Now sew the seam starting at the fold on the hem. If you haven’t used this method before you may want to sew one side first and check it to make sure you’re happy with it, it can be a little confusing initially but it’s worth persevering.
Turn the hem to check it is level and, if you’re happy with it, neaten the seams however you wish. This is before I neatened the side seam but it will look like this on the inside.
The outside will look like this, so neat!

One other slight change I made was to the width of the ribbing cuffs, I cut the UK 12 pieces but they were much too baggy for my wrists so I shortened them by 5cms so they aren’t so wide and gapey.

At the moment I haven’t edge stitched any of the ribbing like I would do normally on knit garments. Because this is a combination of woven and knit fabrics I don’t want the woven fabric, at the neck especially, to end up puckered where its attached to the band so I’ve left it for now [and I don’t want holes if I had to unpick it]

The ribbing is currently not edge-stitched in case it causes puckering

I don’t normally post two of the same thing in such quick succession but I wanted to share the hem tip more than anything. I fully anticipate making a knit version of the Fantail at some point, or a short sleeve one in something really light and pretty…That’s what I enjoy about Sewing Revival patterns, so many possibilities if you have the imagination.

Until next time, Happy sewing

Sue

Fantail Top from The Sewing Revival

Janine at The Sewing Revival, the pattern company based in New Zealand, is gradually creating a growing collection of stylish patterns and there is something very appealing in their deceptive simplicity I think. I’ve made a few versions of several of them now, including the Sidewinder pants, the Bellbird top and the Heron dress.

When Janine kindly offered me my choice of the range to choose from I picked one of the more recent releases, the Fantail top. At first glance it appears to be a simple raglan-sleeved top but along with the high/low hemline and elasticated front hem it offers variations of scooped, ribbing or V neck, elasticated or ribbing cuffs, and the back hem can be finished with ribbing too.

I had a rummage in my stash for some suitable fabric, ideally something with a bit of drape works best so soft viscose, crepe, georgette or chiffon if you fancy a challenge, cotton lawn, wool challis or fine linen would all work very well. Light- or medium- weight jersey will make it into a very chic sweater. I’ve no idea where my piece of navy fabric came from, probably I was given it by an elderly lady because it had a little ticket pinned to one corner saying it was 1 1/2 yards x 54” wide and cost 90p! It certainly smelt a little bit musty so the first thing I did was give it a quick hand-wash, it turns out that the colour ran quite a bit and I was left with blue hands for several hours afterwards!!

The patterns are sold in size bands which each contain 4 sizes (there is some overlap between the brackets) and each band is layered which gives you the option to print only the sizes you want so I printed UK 10 and 12 because, having lost some weight recently, I wasn’t sure which size would be best. In the end I cut a UK12 and it looks fine I think, it’s a roomy style so I could possibly go down a size but as I’m one of life’s ‘fluctuaters’ where weight is concerned maybe I won’t.

I like the instructions on Sewing Revival patterns because they are well explained and illustrated with photographs. If you’re an experienced sewer like me then you won’t necessarily need to follow them closely all the time but I do keep half an eye on them so that I don’t miss a step or construct in the wrong order which might have repercussions later on.

I made the scoop-neck version with elasticated cuffs which is probably the most straightforward variant, the round neck is just the right amount in my view, not too wide, not too deep. Raglan sleeves are super-quick to construct, I usually sew the neck facing on after the shoulder seams and before sewing the under arm seams.

The front and back hems are very different lengths and finished differently so don’t rush through these elements. I ignored the suggested bias-binding finish on the back hem and used one of my favourite techniques of a pin-hem instead ( I wrote instructions for this last year in this blog post on hems )

The USP of this top is the deep partially-elasticated front hem. It looks great but it’s really not difficult to achieve. There are suggested lengths to cut your elastic for each size although you could use a shorter piece over the same length if you want to pull the front in a bit more. Or you could also use a narrower elastic but the pattern is cut for wide width like this so you may have to make an alteration to the hem depth accordingly for the channel to work.

This is the side seam where the two levels come together, make sure the back hem is fully enclosed within the front so there is a nice smooth line from front to back.
The finished top on the stand.
I sewed the deep elastic cuff version, there’s a subtle amount of gathering.

As I said, this is a simple top with eye-catching details, it’s probably a half-day project if you’re got everything you need when you start.

The sun came out so we headed out to the garden for photos. I’m wearing one of the pairs of Sidewinder pants I made in 2019, they are a bit baggy now.
There’s a nice dip to the hem at the back.

I’ve already got some fabric lined up for another Fantail hopefully very soon, a nice piece of soft viscose from Sew Me Something and ribbing given to me by my friend Kate which by sheer good fortune coordinates perfectly! There’s lots of possible variety with the Fantail, short sleeves is another for example. Incidentally, there is also a slightly different sleeveless version of the Fantail available too.

Until next time, Happy sewing

Sue

Box pleat shirt from Trend Patterns

I’ve made loads of different clothes over the decades but actual shirts for myself have not tended to be among them. I’m not sure why, possibly because I had to wear boring school shirts for years and years, and for a while I had to wear a uniform when I worked for the John Lewis Partnership so my personal preference has tended to softer blouse shapes. That said, I love to see a crisp white shirt especially when it’s given an inventive twist. It’s a wardrobe staple and yet there’s always room for a new version. 

Lucy at Trend Patterns has just released the first 3 patterns of what will become a shirt collection and each is available printed, as a PDF or as a complete kit with pattern, fabric and trims. TPCSH1 is a feminine Pussy bow top with shirt sleeves and a ruffle hem, TPCSH3 has stunning gathered ‘angel’ sleeves which really make a statement whilst the body is kept simple and traditional so that the sleeves do all the talking. 

Lucy offered me the kit of TPCSH2 to try out, it is a box-pleated front shirt, deceptively simple to look at but those details take a little time to get right. It’s classified as ‘moderate/hard’ and I would agree, not because the elements in themselves are especially difficult but each of them needs some experience and precision to execute so I wouldn’t recommend this as your first shirt project. 

The kit comes with enough good quality plain white cotton poplin to make up to the largest size of a UK 22, along with Trend-branded buttons (a nice touch) and iron-on interfacing. All you need to provide is your own thread! 

I started off by taking my measurements and comparing them to the sizing chart, there is also a chart giving you finished garment measurements too which is helpful because it will give you some idea of how oversized the shirt will be when it’s finished. I made a UK 12 and as you will see from the finished photos it’s a very generous fit, to be honest, if you want a close-fitting shirt then this particular pattern won’t be the one for you. 

I opted to trace off the pattern, there are two separate fronts, right and left, and a whole back plus sleeves, yoke, cuffs and collar. There is no pattern piece for the bias binding for the sleeve placket, you just need to cut yourself two bias strips approximately 30cms x 4cms. The right and left fronts are the same except for the extra on the centre front which creates the folded fly with concealed buttonholes. I traced off one front then, to save some time and to ensure they were identical, pinned it to more spot and cross paper before cutting them out together so that I had a mirror version with the additional front added. It’s really important to trace the front very carefully because of the three box pleats, if they are each a bit off you risk the pleats not sewing together accurately which will leave you scratching your head. There are a lot of drill holes to mark the stitching which will eventually hold the pleats in place, don’t be tempted to miss any out because they are also really helpful when you’re folding and pressing the pleats in position. You could choose to trace just half the back to save paper if you intend to always cut it on the fold anyway but having a whole piece gives you the option to have the fabric out flat, besides, it’s almost always more economical to cut fabric out as a single layer [this can be especially helpful if you ever need to do some tricky pattern placement or matching]

Because the fabric is plain, placing the pattern pieces and cutting out was a breeze-no pattern matching, yay! I spent quite a while making traditional tailor’s tacks for every single one of the drill holes. You could use a washable or some other kind of disappearing marker pen if you are confident that it definitely won’t come back to haunt you but I wasn’t going to take the risk on plain white fabric! 

In the past I’ve occasionally found some of the earlier Trend instructions a bit tricky to follow but the more recent ones have illustrations rather than photos and I found this set very clear. My biggest piece of advice would be to read then re-read the instructions before you start, and to highlight anything that you know you’re going to have to really concentrate on, this isn’t a race after all. 

Constructing the fly front and button stand first, including the buttonholes, was satisfying, I often feel like I’ve run out of steam by the end of any project which requires buttonholes and it’s a bit of a chore by then but this gets it out of the way nice and early. [I should add at this point that I started out sewing with a fine size 60 needle so as not to leave too many noticeable puncture holes in the plain fabric if I went wrong or needed to unpick. However, this size needle kept skipping stitches for some reason so I went up to a 70 and had no further problems]

transfer all markings and instructions to the paper pattern if you’re tracing it off. I made tailor’s tacks through every drill hole

My second piece of advice would be to press your pleats on the ironing board if you possibly can. I only have a small heat-resistant board in Threadquarters which meant I was constantly moving the fabric which was not ideal, it was so much easier on the ironing board because the whole piece fitted on. Do not rush this part, with pure cotton fabric you can have the iron on pretty hot but do be careful of your fingers with hot steam. Pin, tack or Wonder Tape the pleats in position once pressed if you want to. 

pressing the pleats on the ironing board, the snips top and bottom along with the tailor’s tacks will help you get each one in exactly the right place.
In progress-making the bar tacks

The instructions are to stitch down each pleat according to the markings using a few stitches. I did quite a lot of testing using a variety of decorative stitches for this before I committed to the bar tack. The next challenge was getting each of those bar tacks (30 in total!) central over the pleat. My machine comes with a number of feet which are used in conjunction with the decorative stitches and one of these has horizontal red lines which proved very helpful in getting lined up for every bar tack. After making a few of these bar tacks I ‘got my eye in’ so I could tell very quickly where to start each stitch, having the needle stopping in the up or down position is an absolute essential feature on my machine for me and it was brilliant during this, being able to lift the foot to check I was sewing in the correct place without the work shifting was so helpful. The photos will hopefully make my method clearer to follow. It’s vital to take your time and be as accurate as possible during this stage because the box-pleats are the USP of this shirt and it will obvious if they are off-kilter. I sewed in white thread but you could use a colour, or even hand embroider to give your shirt a totally original look.

testing various stitches including triple straight stitch and arrow heads, the difficulty was going to getting every single one central over the pleat

Incidentally, Trend will be creating a series of video tutorials to help so I suggest you check their Instagram account or the website for those. Also, there was a slight problem with pattern markings for the back box pleat which were incorrect. This has been rectified but if you bought a copy very soon after release you might find you have to scratch your head a little, the notches were in the wrong places. Check the website if you’re in any doubt.

the right front, including the fly, taking shape
the shirt with the side seams now sewn up, ready for the sleeves to go in
sewing the continuous binding to the sleeve opening. the instructions don’t call for it but I like to sew across the top of it at a 45 degree angle to encourage the binding to stay on the inside
close up of the finished front
all done
close up of the finished bar tacks

I followed the order of construction to complete the shirt (I usually do the first time I make a pattern) but personally I would put the collar on after making the yoke. I like to do it before the side seams are sewn up or the sleeves are inserted, unless there’s a technical reason not to obviously. 

the finished back yoke
I popped a bar tack in the middle of the back to hold the pleat in place, this hadn’t had a proper press yet

Everything came together really well, I’ve always found Trend patterns are accurately drafted so I know the pieces will go together well without major discrepancies-this is why it’s so important to trace off carefully if it’s your preferred method, if seams or notches don’t match up you won’t know where the fault lies [the same applies to accurate cutting out too] 

The sun came out so we could take some outdoor photos, I’ve paired the shirt with my much-worn Megan Nielsen Ash jeans
is it a bird? is it as plane?…
I’ve pressed the pleat now

Clearly not everyone will want to make a shirt that is going to take a sizeable amount of time to construct, or to launder afterwards for that matter, but if we only made simple loungewear for ever then the art and skill of making our own clothes will be lost, just at a time when so many people have discovered, or rediscovered, the joy of sewing for themselves. There will always be a place for a classic white shirt and Trend has created a small but growing collection with original twists on the genre. The last year has been so tough for small business owners so I really appreciate being given this kit to try out, I wasn’t under any obligation to review it other than share some photos but personally I have no problem with sewing and writing about it. I will always try to give you a balanced view and if I can support a little business by giving them some positive exposure then I will. Alongside that I’m keen to demonstrate that a design-led style doesn’t have to beyond us ‘ordinary’ sewers either, if you like it then sew it! 

I hope I’ve given you some idea of what will be involved in making the TPCSH2, if you’re looking to push your skills on a bit this could be a good project. Maybe you need/want a plain white shirt in your wardrobe [amazingly I didn’t have one in mine, just a couple of short-sleeved ones] I might layer this with a sleeveless tank top over it, or a waistcoat could look interesting. This is a typical cotton poplin shirting but you could use a variety of fabrics, you could have fun with graphic prints or stripes, try something soft like double gauze or a crisp linen? Or what about harvesting the fabric from several well-worn mens shirts to make a more patchwork look. Take your time though and enjoy the process.

I’ve got a long-sleeved T-shirt under it because it was a chilly day and it will be perfect for the day I can return to the V&A. I don’t know about you but I’ve really missed putting an outfit together to go on a nice day out, deciding which of the lovely garments I’ve made that I want to wear and how I’m going to accessorise them. It seems such a small silly thing to miss but I shall be so glad when I can start doing it again.

Most of all, thank you to Trend for giving me the opportunity to try the kit, until next time,

Happy Sewing

Sue

a multitasking Festive outfit

The Festive season is often a reason to make, or buy, a special new outfit to wear for office parties or Christmas Day but this year’s Festive season things will be very different for most of us. I don’t want to be entirely negative though so, as part of the Lamazi blogger team, I thought I’d make something which is a little bit Christmassy but will double up as a ‘regular’ winter dress too. 

I’ve chosen the cord velvet from Danish Design in a gorgeous shade of aubergine-I’m always a sucker for purple-but it comes in several other beautiful rich shades including a sumptuous gold and a stunning teal too. I picked this fabric because it’s a medium weight stretch jersey and has soft pile which makes it lovely to the touch. I’ve made a dress but you could easily make tops or wide-legged pants in it, or babies and children’s clothes too because it’s washable and crease resistant. 

Whilst I love a complex make to really get my teeth into I felt this wasn’t a garment which warranted lots of time. Making a special Christmas once-worn garment wasn’t appropriate any longer so I wanted something quite simple but adaptable and for that reason I’ve picked the Somerset T-shirt by Maven Patterns. I’ve made a few of these now, the bones of it are beautifully simple, it has a self-neatened bateau neckline, a slightly fitted silhouette and four sleeve options. I’ve chosen the Bishop sleeve with a long cuff but I’ve hacked the sleeve to make it even fuller, and I’ll lengthen the body to create a dress finishing below the knee.

Another idea was to add a flared skirt which looks nice but didn’t think I would use it as much as the straight version.

The Somerset has excellent very full instructions with lots of tips and advice to get a good finish. There’s a useful sheet to write all your information including body measurements and fit alterations, and a fabric stretch gauge to check you have enough stretch for the pattern to fit properly. You can also list the needle type and size you’ve used, stitch type and length and anything else you might want to remember for another time. 

To increase the size of the sleeves I took the bishop sleeve pattern and drew 5 vertical lines from each of the notches from shoulder to hem. Each segment will become slightly wider as it gets nearer the bottom edge so make sure they are even in size.

Cut a piece of spot and cross or tracing paper bigger than the pattern as it is, mark a grainline running right down the paper and then lay the pattern piece on top of it, matching the grain on the pattern to the grain line you’ve just drawn. Next, I carefully cut up to the top of the marked lines taking care not to snip right through at the top, keep it attached by a tiny amount to act as a pivot point. [If you don’t want to cut your original pattern piece I suggest you trace off a new one to use instead] Then you splay the hem edge apart by a few centimetres each, I added 2.5cms between the each of the ‘side’ segments and 5cms to the central one. By doing this you’re adding fullness at the hem but not altering the sleeve head. You could put additional fullness to the sleeve head by opening the top edge too if you wanted. I lengthened the sleeve by 5cms too so that it would have plenty of blousy fullness into the cuff. 

Trace around the new shape using a tracing wheel or pencil and cut out the new piece transferring all markings. One final change I made was to add a bias grainline because I knew I wanted to play with the stripe direction of the rib on the fabric.

I had pre-washed my fabric and partly tumble dried it on ‘low’ before letting it dry completely on the clothes airer, it seemed to survive the experience just fine. 

I made an arbitrary choice of how long to make the dress by simply holding the tape measure at my shoulder and seeing where it came to at about mid-shin! I attached another piece of spot and cross to the bottom of the front and back pattern pieces and drew on the skirt length I wanted, plus a generous hem. I knew I would have to make some adjustments to the hip and thigh during the fitting stage, just make sure that the hip and thigh measurements are plenty big enough because you can always remove some, it’s much harder to add later! 

The ‘cord’ runs across the width of the fabric and I wanted the rib to run down the length of my dress which meant I had to fold the fabric across the width. Try not to twist the fabric if you have to fold this way, I marked a single rib by following it across the width with pins so that I can see it clearly. Fabrics like corduroy, velvet or velour have a pile or ‘nap’ which will shade so if you cut some pieces facing one way on the grain and some pieces running the other way then you will end up with a garment that looks like it’s been made with two different colour fabrics, even though you know that isn’t the case. If you’re unsure what quantity of this type of fabric to buy go with the ‘with nap’ amount on the pattern information and follow the one-way layplan to cut out.

I marked the rib across the fabric with pins so that I could be sure it was folded correctly and would not be twisted.

Once I’d cut all my pieces I followed the making instructions which are very comprehensive. If you have a walking foot for your machine I strongly recommend you use it because velour like this has a ‘pile’ and has a tendency to ‘creep’ as you sew so you might find that it starts off with all the edges matching but by the time you get to the other end the two fabrics are no longer matching. I also strongly recommend you tack any seams you are unsure about. You could use a million pins but by the time you’ve done all that you could have basted it in place which does the same job and usually more effectively. I was able to coverstitch the neck and the skirt hem on the Pfaff Coverlock 3.0 I have on loan as a brand ambassador but it works just as well by overlocking the raw edges and twin-needle stitching them down, or zigzag and twin-needle, or two rows sewn singly if you don’t have a twin needle. When it comes to pressing a fabric like this, if you don’t have a special needle board (and few of us do) then you should press on the reverse at all times. You could place a towel on your pressing surface and lay the fabric on top so that the pile of the cloth is against the pile of the towel which will help protect it. Use a pressing cloth as well. These tips will also apply to regular corduroy or any non-stretch fabrics with a pile too.

The bell of the sleeve is gathered using shirring elastic which helps to retain some of the stretch required for the cuff. 

Once the sleeves were in I sewed up one side seam directly on the overlocker and then pinned the other side seam to fit myself. This was because I didn’t know if I’d need a split at the hem to be able to walk in the dress and I didn’t want to end up with loads of unpicking!

First I tried it right side out to get an idea of how it was fitting initially, then I turned it inside out to pin.

I looked at the fit in the mirror first of all and the sewn side seam was quite wavy, this could be cured by either adjusting the differential feed on the overlocker so that it doesn’t happen, or you could stitch the seam on the sewing machine and then overlock the edges [This is what I opted to do because I could see I had to take a fair bit off the side seams anyway to achieve a fit I was happy with] Then I put the dress on inside out in front of the mirror and pinned out the excess. I turned it right side out and tried it on again to check the fit, then finally sewed both side seams on the sewing machine, I used a ‘stretch’ needle, a ballpoint or jersey needle performs the same task. Either use a short straight stitch or a straightened out zigzag, make some samples to see which works best for your particular fabric. 

Now I tried it on the dress inside out to adjust the seams
I pinned out a fair bit of the side seams to give more shape through the waist and hips.
still Inside out
Finally I put the pinned dress back on the right way around to check I was happy with the fit before making the adjustments.

Lastly, the cuffs go on and the skirt is hemmed. 

And that’s pretty much it, it pops straight over the head so no tricky closures, because of the stretch it didn’t need a split, and that means there’s room for Christmas lunch and it won’t look like a dish rag after spending the afternoon curled up on the sofa watching Christmas telly!

cheers!
I’ve dressed it down with an ancient knitted gilet plus a wide belt, long boots and my much loved Alexander McQueen scarf
I love a scarf to keep my neck warm!
It could be the strangest of Christmases but let’s raise a glass to a much better 2021

I have to say that I’m really happy with this dress because it ticks all the boxes I wanted it to. It’s comfortable but it looks Christmassy, it looks great with opaque tights, heels and jewellery, but also with boots, a chunky belt, a roll neck top underneath for extra warmth or a cosy scarf…and did I mention it’s comfortable! #secretpyjamas It also has the advantage of rolling up and going in the corner of a bag or suitcase and coming back out again not needing a press. Bonus!!

If you have a favourite T-shirt pattern you could try lengthening it into a dress, Tilly and the Buttons Tabitha from Make it Simple does that. You could browse the SewOver50 post I wrote listing loads of go-to T-shirt patterns for inspiration, or maybe copy a RTW one you already have?

At 160cms the fabric is very wide so a little will go a long way, and because it’s so soft it would be lovely for children’s wear too. It needs a little bit of careful handling but a lot of that is in the ground work. Make sure you lay it up and cut it accurately to minimise unnecessary stretching or distortion (try to keep it flat on the table or lay it up on the floor) pin or tack the seams so they don’t move about and press carefully as you go and you should be fine. 

It’s been an incredibly tough year for so many and I wouldn’t blame you for not feeling like making anything new to wear. However, if crafting and creating bring you joy and respite then you could view it as a gift to yourself, and when you choose to buy from small companies like Lamazi and Maven then you are helping them too.

Thank you to Lamazi for providing me with the fabric for me to write my review, and I hope you find it helpful. 

Until next time, Happy sewing

Sue

Revisiting a ‘vintage’ blouse pattern

I know many of us often sew patterns multiple times because we like them but I’ve taken this to a new extreme recently. I last sewed this blouse pattern Simplicity 8704 when I was around 16 or 17 years old, the date on the back is 1978 so I must have made it while I was still at school! I remember I used a burgundy-coloured viscose (or similar) with a floral print on it and it was definitely one of my favourites as I wore it a lot, probably swanning about in the Sixth Form common room!

There have been several times when I’ve been tempted to revisit it but for one reason or another I’ve put it back in the box for another day but this time I kept it out and went in search of fabric in the stash. Initially I was going to use a really pretty pastel pink lightweight checked cotton I got from Sew Me Sunshine (I can’t see it on the website now though) but when I realised I was going to have to pattern match the deceptively tricky check I thought better of it. I wasn’t in the mood for taking an age over that so I continued to rummage until my eyes fell upon the (also) pale pink linen I acquired from the local Scraps Store last year. I found it in a container full of various unwanted fabrics and there was nearly 5 metres of it so, for a donation, it came home with me! I laundered it at the time but put it away. I thought I might make a dress with it originally but, because it’s such a pale pink, I didn’t want to end up looking like a blob so I left it for another time.

A plain linen blouse appealed to me though and I didn’t have to fiddle about pattern matching so away I went and it was cut out in no time. Even though the pattern was a single size-this is how most patterns were sold until multi-size patterns were introduced-and my size has fluctuated to say the least over the years, amazingly it was still going to be the right size with no alterations.

There’s not much else to say about making it up except I remembered that an @SewOver50 stalwart, Lisa, had shared on her grid the day before that she had used a wing needle to decorate a plain linen tunic she was making which reminded me that I’d intended to find a use for the same effect at some point but forgotten all about it-Thank You Lisa!

The wing needle (I’ve also seen it called an ‘heirloom’ needle recently too) is like a regular needle except it has fine metal ‘fins’ to each side of the shaft which creates a little hole like a tiny eyelet in the centre of the stitch as it forms. A stitch which looks like a little star works best for this effect but you could try experimenting to see if any others look nice

I made a little video of my machine in action.

It’s worth bearing in mind a couple of important points if you’re going to use this decoration. Firstly, you can’t easily pivot at a corner with the needle down in the work-I sewed the collar in three separate moves, secondly you won’t be able to use the automatic threader if your machine has one and thirdly (thank you Lisa for telling me this because I don’t have this feature) you can’t use your automatic thread cutter if you have one.

As well as the collar I embroidered the cuffs, the front raglan seams and down the button placket, although I did this last one after I’d hemmed the bottom and sewn the buttonholes so that it was the exact distance from the edge and the buttonholes.

I love the way the blouse gathers into the collar, which is a two part construction incidentally, the raglan sleeves are straightforward but the gathered cuffs add a nice touch. I found a selection of Mother of Pearl buttons amongst my tidied-up button boxes to add another of my usual quirky details but otherwise that’s it. It’s a reasonably quick make but it was lovely to sew the details of collar construction and the cuffs, there’s an elegant simplicity to it I think. I will either wear it loose over the top of trousers or tucked in, or underneath a pinafore dress maybe?

It might sound strange but it feels a bit like an old friend has come back to visit, and I might even make the placket front version now too!

Until next time, keep sewing!

Sue

Simple Sew Amelia tea dress hack.

The Amelia tea dress isn’t one I’ve sewn before but Jane who comes to my sewing class had made one last summer and I remember liking the shirred elastic midriff section. The brief for our makes this time was ‘festive’ (we usually don’t have a brief, it’s free-choice) Bearing this in mind Bobbins n Buttons had offered to provide me with fabric so I had a browse on their website and selected the Lady McElroy ‘beauty and the bees’ stretch velvet. 

The pattern isn’t intended for jersey but it is simple shapes and a bit of gathering which I knew would still work well, what you don’t want is a fabric that’s too thick or stiff though because the shirring won’t work properly. I planned to hack the pattern a bit so I decided to add long bishop sleeves as it’s winter, I also lengthened the skirt (more on that later) and of course I added pockets! 

Because of the distinctive large print I opted to remove the centre back seam and put the zip into the side seam instead, this was to save me the hassle of trying to pattern match the print across the zip. Because I’d removed the CB seam in the bodice I took it out of the skirt too, for the same reasons. If you’ve got a tricky print to match over a seam like this consider whether you can move the zip to the side, it’s not much different to put in and the opening can be a little shorter but still give you sufficient room. Now I could have a line of bees central down the back (and front of course) and just needed to get a good horizontal match too for me to be really happy.

As I said before I wanted the skirt as long as possible but there needs to be a compromise between length versus flare because of the width of the fabric. If you want the skirt to be longer you’ll need to reduce the amount of flare at the hem because you’ll be restricted by the fabric width. The wider the fabric then the more scope you have. I measured how long I could make the skirt before it would need reducing at the hem and decided it would be an acceptable length. I could add around 10cms to the hem making sure the new side seams were at a right angle to each other so that the hem will run in a smooth lineI traced around a few bees where they crossed the cutting line so that I could ensure the front and back matched as well as possible. 

In order to cut everything as efficiently as possible from the fabric I first cut the skirts against the main fold-don’t forget to exclude the CB seam or the piece will be bigger than your back bodice (if you’re excluding the zip) 

Then I refolded the fabric with the selvedges into the centre to cut the bodice pieces on the folds. This is vital to get those bees running down the centre. 

From the remaining fabric I cut a pair of long sleeves. I used the pattern from another design I’ve made a few times, I measured the armhole of the dress and compared it against the sleeve I have. It was a little smaller at the crown so I added a small amount to give it sufficient widthFinally, because it’s jersey, I chose to use a neck binding instead of the facings so I cut two narrow strips which were each the same length as the CF to CB measurement of the neck plus a couple of centimetres seam allowance. 

I increased the sleeve head by 2cms, moving it out by 1cm either side of the shoulder notch.
It’s important to keep the sleeve level when you add the extra width so draw a line at a right angle to the grainline, then move the pattern piece 1cm in each direction using the line as the axis.

Ok, so I mostly followed the instruction with a few minor changes because of my alterations. One thing I did first of all was to stabilise the back shoulder seams and the left side seams where the zip was going to go with iron-on interfacing because I don’t want them to stretch out of shape. I chose to leave the back darts in although I possibly could have eased them out as it’s a stretch fabric.

stabilised side seam before the zip goes in.

After joining the shoulder seams I added my neck binding. I folded the strips with RS out along the long edge-I didn’t join them to each other at this stage-then, starting at the V, I stitched just that section into place. This way you can sew just a small part, snip into the V and pivot at the corner more accurately. When I was happy with this I sewed the rest of the binding on leaving just the CB part unsewn, then I could join the two strips in the right place and finally attach it to the neckline. Finally I neatened the edge all the way around and then topstitched it down close to the seam to stop it rolling. 

The next part is the shirring which really isn’t difficult so don’t panic. First wind shirring elastic onto an empty bobbin BY HAND stretching it very slightly as you go, put it into the machine in the usual way (you may wish to check the manual if you have an older machine in case there is anywhere else you need to thread the elastic through) Use your matching colour thread on the top in the usual way and lengthen the stitch slightly, it doesn’t need to be zigzag or anything though. Definitely try out a test piece first and don’t forget to secure the start of each new row so that the stitching doesn’t come undone. I don’t secure the other end at this stage though in case I find I need to pull the threads up any more later. You should be able to sew 8 rows of stitching parallel to each other to complete the strip. The fabric will naturally pucker up pretty well but when you’re done stitching hover the iron with plenty of steam over it and you’ll find it gathers up some more as a result. Finally knot the ends of the threads to secure.

Then you need to attach the gathered band onto the lower part of the bodice making sure it’s evenly divided as you go.

Attaching the shirred waist section to the upper bodice.

Attach the skirts (I’d sewn the pocket bags on to each side seam before doing this. I just use my handy cardboard template which I made ages ago, I just trace around it directly onto the fabric and cut out.) 

Next the zip goes into the left side seam. I sew it here out of habit as I’m right-handed and find it easier to do up that way but put the zip in whichever side works for you. After neatening both side seams separately first I sewed up the top of the side seam by about 4cms from the armhole edge. I used an invisible zip and inserted it in the usual way, making sure the waist seams matched, and then joining the rest of the side seam once I was happy with the zip insertion. I sewed up the other side seam and I was ready to tackle the sleeves.

The sleeves are set-in so I made the elasticated cuffs on the flat first using straight strips of jersey the same length as the curved cuff edge. With the strip open and RS together I sewed it once. 

Then I folded the strip in half and sewed it on the overlocker to create a channel.

 This will turn downwards to form the cuff which I slotted wide elastic through, securing at both ends. 

Finally, I sewed the underarm seams to create the sleeves which are inserted into the dress as per the instructions. 

All that’s left to do is the hem which I sewed on the coverstitch machine which is on loan to me by Pfaff at the moment. 

I’m really pleased with how the dress has turned out, it’s very swishy and has a slightly 1940’s vibe to it. I like the extra length on the skirt and the sleeves look fab. I was a little alarmed when I saw the large scale of the print but actually I really rather like the bees now. One thing I’m not keen on (and this is down to the manufacturer and not the supplier) is that they have printed a black background design onto a white base cloth. Because the cloth has a pile it means that anywhere there are joins there is a slight hint of the white showing through which is not ideal. The velour isn’t too tricky to work with as the pile is a bit flatter than velvet but it does still ‘creep’ a bit in places so if you’re in any doubt that pins aren’t enough to keep it all in alignment make sure you tack (baste) seams together. If you have a walking foot I would definitely advise using it. 

Lots of pictures swishing about!

I hope this will help you to feel inspired and perhaps have a go at ‘hacking’ a pattern for yourself. This was a very simple one but if you look at my Simplicity blouse hack you can see just how carried away it’s possible to get!

Until next time, happy sewing

Sue

Sidewinder pants by The Sewing Revival

The Sidewinder pants are my third make using a pattern from The Sewing Revival following on from several versions of their Heron dress and Bellbird top. I’ve already written reviews of them which you can read about here and here, plus I made a new version of the Bellbird at the recent Sewing Weekender in Cambridge, organised by The Fold Line.

The Sidewinders are a very simple pull-on trouser pattern with a tapered leg but their USP is the diagonal side seam which gives them such an interesting ‘twist’. They are flat-fronted with an elasticated back waist and of course there are pockets in the seams too. There are variations at the hem too as you can choose plain full-length, 7/8ths with turn-ups like mine or use wide elastic to gather the hem into cuffs. As you can see from the artwork they could be very casual or dressed up with heels, fabrics with a bit of body but some drape and softness are suggested. Like the other Sewing Revival patterns these are PDFs so you can buy, download and print your pattern any time, or have them printed for you on A0.

As I’ve come to expect with SR patterns the instructions and illustrations are very clear and personally I’ve always found their sizing very good too. I cut the large based on my measurements although I did decide to shorten the leg length very slightly as I didn’t want them ‘pooling’ around my ankles too much, the idea is that they sit above the ankle bone. The instructions tell you what length of elastic to cut for the back waist which you can then adjust to suit.

For the first pair I used some Royal blue crepe fabric which was leftover from the Trend Asymmetric dress I made last year. If you’re using a plain fabric these trousers are surprisingly economical to cut and if you’re short of fabric you could cut the pocket bags and waist band facings from other fabrics too. You could have fun with stripes or checks to give them a bit of a Vivienne Westwood vibe but you’d need more fabric for that. What about using ribbon or piping down the side seam for emphasis?

Construction is very quick, I’d say that this could be a half-day project if you aren’t getting fancy with pattern-matching. I really like the way that the waistband is a facing because when it folds over the top it secures the pocket bags in place, you only need to neaten the lower edges of them. The elastic gets slotted through the back channel which extends slightly around to the front beyond the ‘normal’ side seam position. Once this is stitched in place you sew down the facing at the front. This line of stitching isn’t near the edge, it’s approximately 3.5-4cms away depending on the width of your elastic so use a guide of some kind to keep it parallel, I always use the quilting guide which comes with my machine or you could use Washi tape or similar stuck onto the bed (I’m not keen on this personally as I wouldn’t any sticky residue near my fabrics but I know others use this method)

These are the second pair which I made at the Weekender and that is why some of the overlocking is different colours.

As I said earlier I’ve made both versions with a small turn-up so once I’ve turned them up I stitched through seam lines of the inner and outer leg seams to hold the turn-up securely in position.

You’ll notice from the grey version that I contrast top-stitched in pink either side of the outer leg seams to give some emphasis to the diagonal seam, I like how it goes ‘off’ at the hem.

The blue pair are sooo comfortable because the crepe fabric has quite a bit of natural give, and the back elastic gives a nice snug fit without being too tight. My blouse here is a longtime favourite, the Imogen from Sew Me Something
There was enough fabric to make a belt which ended up being massively long so it goes round twice into a big bow!
And these are the grey pair which I teamed with the second garment I started (but didn’t finish!) at the Weekender which is another Sewing Revival Bellbird made in a very lightweight woven check cotton which I picked up on a swap table somewhere last year. The label was given to us by lovely Harriet of Sew me Sunshine which is a really nice reminder of what I made and where!

Janine at The Sewing Revival generously provided me with the pattern for the Sidewinders and I’ve been more than happy to write a review because I love these trousers! I’m planning to make more for the winter and I’ll definitely give a gathered ankle pair a try too.

After a few weeks of sewing for others, writing (and then completely rewriting the Sew Over 50 birthday blog post because I lost ALL 4000+ words!!!!) and being away from home it’s lovely to get back to a bit of sewing for myself and sharing my thoughts with you. I’m so happy that I discovered The Sewing Revival as a result of our first Sew Over 50 challenge at the beginning of the year, did you find any new patterns brands as a result too, that was certainly our hope.

Until next time,

Happy Sewing

Sue

French dart shift by Maven Patterns

IMG_4586

This could very well be the perfect dress for the imperfect figure. It sits nicely on the shoulders with smooth set-in sleeves that blouse slightly at the cuff (if you’re going full-length) the French darts give it shape and the slight A-line flare of the skirt skims the body, it has pockets and finally there’s a funnel-neck collar to draw attention up towards the face if that’s your best feature! Oh, and there’s no zip, just pop it over your head!

I bought my pattern from the lovely Mike (son in law of Mrs Maven) who was manning the stand at the autumn Knitting & Stitching show for Mrs Maven who’d had to dash off for a family emergency. He must have done a grand job because I bought a pattern, as did many others while I was there, the samples on display were very enticing.

The French Dart Shift appealed to me because I liked it’s relaxed but stylish aesthetic, there are lots of possibilities. It has 3 sleeve options (plus sleeveless) and you could make it in a whole variety of fabrics from winter-weights like worsted wool or denim, through cotton poplins to softer fabrics like crepe or lace with suitable linings.

The patterns aren’t cheap at £18.50 but they are beautifully produced in a folding wallet, printed on quality paper with a comprehensive instruction booklet. I decided to trace off the pattern onto Swedish tracing paper rather than cut it out-I don’t always do this as I’m not an habitual tracer! I checked my body measurements and then using the measurements chart provided so I went for a UK 14. fullsizeoutput_2154

IMG_4590
This time I transferred the pattern to Swedish tracing paper.

I had a rummage in my stash and found some navy fabric with tiny dots which I bought ages ago in Hitchin market and there was just enough. I didn’t follow the cutting plan as I hadn’t got the suggested quantity but by careful refolding and some single-layer cutting I got everything out.

One detail you need to watch out for is that the seam allowance is just 1cm rather than the more usual 1.5cms. The instructions are comprehensive and thorough although if you struggle with following written instructions this might be a challenge for you. There are illustrations too which are very detailed but they could do with being just a bit larger for those of us who are a bit sight-challenged, I managed but that’s partly because I had an inkling of how it was likely to go together.

The instructions encourage quality details such as taping the neck and pocket edges to prevent stretching (I actually used iron-on tape which fulfils the same job) and reinforcing the joins between the pocket bags and the side seams.

I failed to take any photos during the making, sorry about that, but it all went together as intended. The band on the cuffs is quite narrow and a bit fiddly but it’s worth persevering because the end result looks nice. You could leave the cuff off i suppose and make a channel with elastic through it if you wanted, or you could shorten the sleeve to between wrist and elbow length too.

IMG_4274
the narrow gathered cuff is very feminine

IMG_4273
The collar is cut on the bias which gives it a lovely roll and it stands well on it’s own, there’s no interfacing inside it. If you were making the dress in something more flimsy (like cotton lawn for example) you could mount the collar onto a fine fabric like organza, or a second piece of lawn or voile to give it more body.

IMG_4272
Finished, I actually hand-stitched the hem so that it was nice and invisible.

I finished the navy dress before Christmas-I wore it on Christmas Day in fact, but I’ve only just made a second version recently [a 2 week bout of flu put paid to any creative sewing for a while]

I’ve made this second version in a lovely Ponte Roma I bought from Fabrics Galore at the Knitting & Stitching Show 18 months ago (I don’t like to rush these things) Although Ponte isn’t one of the suggested fabrics it’s worked well but you need to make sure that the wide neck edge is taped to prevent it being stretched before you put the collar on.

I think I can safely say this dress is my ‘secret pyjamas’, it’s sooo comfy!

fullsizeoutput_2159
Whoop, the sun came out so here’s some pictures in the garden. I used the twin needle to turn up the hem on this one.

fullsizeoutput_2160
I chose not to cut the collar on the bias because it’s a slightly stretchy fabric and this has back-fired a bit because it’s collapsing. Never mind, we live and learn, I should have followed my own advice and mounted it onto something else for a bit of structure.

IMG_4598

All in all I’m delighted with this dress and I can see me making several more for the summer. Take a look at the Maven website for more inspiration with fabrics, you could even leave the collar off, and I know Portia Lawrie has produced a colour-block version too which looks fab. I think I’ll investigate some of Maven’s other patterns now too as they look really appealing!

Let me know if you’ve tried any of them,

Happy sewing

Sue

I made a coat!! Butterick 6423 to be precise…

Two years ago I did a 10 week tailoring course at Morley College, London but it’s taken me until now to actually make my own coat. I settled on Butterick 6423 partly because it’s a fairly similar silhouette to a RTW coat I already own and wear a lot, and then, ironically, it came free with Love Sewing magazine just before Christmas.

Butterick coat

Added to this I had 3 metres of lovely turquoise-coloured wool in my stash that was gifted to me about a year ago by a friend who was clearing out her mother’s belongings and wanted the fabrics and patterns (LOTS of them) to go to an appreciative home. Not only that, I had just under 2 metres of almost psychedelic lining fabric which came from a different elderly lady ( I had no idea what to do with it at the time but, as is often the way, it goes really well with this wool)

Because I had plenty of fabric, which makes a change for me as I tend to underestimate, I could cut out the coat without having to watch every centimetre. I didn’t have quite enough lining though so I cut all the pieces which would be visible inside the main body and the sleeve linings I cut from plain lining, again from my stash.

fullsizeoutput_20df
Sleeve lining, with 4cms of the length folded out

Initially, before I cut the fabric, I pinned the tissue together to check it on my dress-stand. I chose to take 3cms out of the overall body length and 4cms out of the sleeves because they seemed terribly long. This proved to be sensible as you’ll see in the finished garment.

IMG_4433
I used loads of good old-fashioned tailor’s tacks on all the balance marks, I’m not always this meticulous but it proved invaluable for this project.

IMG_4435
coming together slowly…

I found the instructions very clear to follow and I don’t think at any time did I get in a muddle although I do think a common problem with the ‘big’ pattern companies is that the diagrams can be very small making it difficult to see exactly what you should be doing, particularly areas like clipping into important corners eg at the collar/shoulder seam.

Because I do a lot of alterations for people I’ve noticed various techniques employed in the construction of RTW garments. Cuffs, for example, are usually stabilised with iron-on interfacing of some kind so that’s what I did here.

By doing this it stops the cuff from stretching (my fabric is fairly loosely woven too) and gives it firmness and stability. I bought my iron-on interfacing in Goldhawk Rd, London so I can’t really give much detail about it except to say I was told it’s suitable for woollens and tailoring with a light jersey backing. I used it on the collar facing too and it seems to be absolutely fine. You could use a firmer one if you wish, that would make the collar firmer than mine.

There are a few places where you’re told to hand sew hand, attaching the sleeve lining to the inside of the cuffs for example, but if you’re not a fan of hand sewing  it is possible to do this by machine, you just need to get them pinned correctly (double-check you’ve got it right first by turning the sleeve right-side out before you sew it)

IMG_0017
I sewed up the sleeve hems inside using herringbone stitch.

It’s also worth attaching a small amount of the sleeve-lining seam to the sleeve seam inside, this stops any chance of the lining sliding out of the end of the sleeve.

You can do this on the machine, or a few running stitches will do the job.

IMG_0021
This is the inside of the back-neck collar seam. I’ve pinned them together and then stitched to keep the seam from shifting about.

Making the back pleat needs a bit of concentration partly because the lining gets stitched together with it-this makes sense because it reduces the bulk if you’d done them each separately. I opted to partly stitch the pleat together for about 10cms down from the top simply so that it didn’t have a chance to be to flappy in wear. IMG_0024

Once the pleat section is sewn on the instructions say to slip-stitch the lining down. Again, it’s possible to do this on the machine, you need to work your way into the right place by going in through the gap at the front between the facing and the coat front. IMG_0023

IMG_0025

I sewed the coat hem up using herringbone stitch because I think it holds a hem nice and firmly. You sew this stitch from left to right, looping each stitch backwards from the previous one, one above then one below.

Throughout the making process I pressed often and used plenty of steam, with a pressing cloth to prevent shine. If you’re using pure wool you can press and re-press because it’s very forgiving although be more careful if you’re using a fabric that isn’t well or is made with mixed fibres. As my tutor on the tailoring course often said, “steam is your friend” A tailor’s ham is a great boon too because it will enable you to press in tricky areas or under curves seams, for example.

The lining hem was just turned and machined. To neaten the bottom of the front facing I applied a little bit of self-made bias binding, it’s looks nice and it doesn’t add the bulk that turning the edge over could do.IMG_0027

I also added 2 small loops of fabric to hold the lining and the coat together at the side seams, again this stops it flapping about in wear.IMG_0028

I added a hanging loop at the neck which I should have sewn on by machine at an earlier stage but I forgot so I had to sew it on by hand at the end.IMG_0029

IMG_0030
I sewed a few stitches through the CB neck seams to secure the collar facing and under-collar to each other.

The last thing to do is the single buttonhole. I had a rummage for a suitable button first and I came up with a single beautiful mother-of-pearl one which I’d bought a couple of years ago, simply because it’s lovely! I paid £1 for it and I’ve actually left the tiny price label on the back, just because…

I created a surround of tacking stitches to hold the area firm and stable before sewing the buttonhole. I did several trial ones first because my Pfaff is so new to me and I didn’t want to mess it up at this late stage. Unfortunately the thread I’d used for the whole garment was clearly too dark in such a prominent position so I had to go and buy a single reel of thread just for the buttonhole! When I sewed the button on I sewed another small button on behind it so that the fabric doesn’t have to take all the strain of a button being done up and undone constantly.

This is a coat with a slightly retro aesthetic, it’s a little bit 50’s, the back is a little bit 20’s. The result though is modern and wearable and I’m really happy with it.IMG_0060

I love the fun lining inside too. The wool fabric isn’t that thick though so I don’t think I’ll be wearing it when it’s very cold although there is room for a jumper underneath.

fullsizeoutput_2113fullsizeoutput_2111fullsizeoutput_210d

fullsizeoutput_210e
You can see where I’ve sewn up the pleat by about 10-12cms.

As you will have noticed it’s a difficult colour to photograph accurately, the outdoor ones are probably the closest to the real shade.

It’s been an enjoyable process, I took my time over it and I’m very happy with the result. It would be a good project to try if you’re becoming a bit more experienced with your sewing, nothing is terribly tricky, buy suitable but not too expensive fabric and take your time! I’m glad I took some of the length out of the body and sleeves as they would have been very long. I made the size medium and it was plenty big enough, I think the sizing is definitely on the generous-side though so don’t be tempted to go up a size, make a toile if you need to or tissue fit if you can. I didn’t bother neatening any of the seams inside because all of them were going to be enclosed but you could choose to leave the coat unlined and then bind all the seams (Hong Kong finish) which is practical and attractive.

…and the coat cost me barely anything at all!

Because it was the free pattern with Love Sewing I expect there will be lots of versions of this coat popping up over the winter so it will be fun to see how they all vary. Have you made this pattern, I’d love to know how you got on?

Happy Sewing

Sue

A year in sewing 2017

2017 turned out to be a very busy sewing year for me. Not only did I make a loads of projects for myself and occasionally others but I wrote two articles for sewing magazines, and did a multitude of alterations (some very complex and time-consuming) to numerous wedding dresses, along with more mundane hems and sleeve-shortenings too.

This is a quick dash through many of the things I got up to although I’m not sure everything got photographed at the time. I’ve included a lot of links too if I’ve written blogs on some of the things I mention.

January saw a couple of self-drafted sweat shirts, I was particularly pleased with the blue one because I made it from a £3 fleece blanket from Ikea!

There are also 2 Sew Over It Heather dresses, and finally the Grainline Farrow dress, the teal one was the one which featured in the review I wrote for Sew Now magazine.

In February while I was having a week’s holiday in the Lake District I managed to squeeze in a visit to Abakhan fabrics in Manchester and bought fabric by weight for the first time in my life. I also went to a meet up organised by the lovely Emily of Self Assembly Required in a pub at King’s Cross station! I met loads of fellow-sewers there as well as picking up some new patterns and fabrics from the swap including the Holiday Top by The Maker’s Atelier which I’ve made twice over the summer.

Another February highlight was seeing the latest Burberry collection alongside the fabulous capes, each one of which was a stunning one-off! I wonder if there’ll be a similar show this season?

March saw the Moneta party (dress pattern by Colette) so I made my first which I altered to include full-length sleeves, a roll collar and a fake exposed zip (I made a short-sleeved one later in the summer too) I wore it when I went to the spring Knitting and Stitching show where once again I met up with a few fellow-sewers organised by Gabby Young (no relation!) from Gabberdashery vlog.

One of the new people I met was Juliene from Zierstoff Patterns who gave me the opportunity to try out several of their patterns during the course of the rest of the year.

Another new departure was a fundraising initiative with my weekly sewing group. We all spent an afternoon making little ‘pillowcase’ dresses which would eventually be sent off to a girl’s school in Africa.

IMG_0001
our very own Sewing Bee!

Moving rapidly into April I visited the wonderful ‘Five Centuries of House Style’ exhibition at Chatsworth House in Derbyshire, made another Holiday top utilising a few fancy stitches on my sewing machine, as well as a Sophie bolero by Zierstoff. IMG_1725Also during April I was approached to teach some dressmaking classes at a local craft shop so I made some sample garments for that including a dirndl skirt and a jersey tube skirt.IMG_1803 I made the first of 3 Imogen tops using Sew Me Something’s pattern too, more about those later.

fullsizeoutput_1f1f
Imogen blouse and Gina by Zierstoff skirt

In May I went on my travels with my good friend Sue when we walked a section of the Camino di Santiago in France which was a fantastic empowering experience.

In June Mr Y and I went on a cruise to the Baltic and it happened to be a Strictly Come Dancing cruise! The company that make all the costumes, DSI-London, were on board along with many of the dresses so I was in seventh heaven being able to see them close up. I had to write 2 blogs about that just to be able to include all the pictures! you can read them here and here.

By July I was teaching in Hertford and one of the garments was a ‘no-pattern’ kimono which was popular and also the ‘pillowcase’ dress (nothing to do with pillowcases other than a child’s version could be made from one) It’s basically two rectangles of fabric sewn up each side, hemmed at the bottom and a channel at the top with ribbon through it.

IMG_2965

Also in July I made my first visit to the fabulous Balenciaga exhibition at the V&A in London which was wonderful. I’ve actually been 3 times now, each time taking a different friend, I’ve had excellent value from my V&A membership and I’d urge anyone local enough and interested in the decorative arts to think about joining.

I had hoped to go to the second Sewing Weekender in August but I hadn’t been lucky enough to get a ticket….or so I thought! About 10 days before the event I got an email from Rachel at The Foldline telling me that sadly someone had had to drop out and would I like her ticket? Silly question! So off I went to Cambridge and had a wonderful time amongst so many fabulous sewing people, friends old and new. It was my birthday too! I made a simple top while I was there this time, one I’d made before so it was quick, meaning I’d have plenty of time for chatting…and taking on Elizabeth for a Ninja sewing challenge!

We each got given a copy of the same pattern and some stretch fabric off the swap table and away we went, with one hour to get it done. The results were ‘mixed’ shall we say, Elizabeth left out a section and didn’t notice until it was too late and I only cut one piece where I should have cut two so I had to go back and cut that. It was a lot of fun though, even if we looked like stuffed sofas!

The-Sewing-Weekender-2017
Sewing Weekender 2017 Alumni, photo by The Foldline.

I spent September making the top and trousers that I’d be modelling in Love Sewing magazine! This was certainly one of my sewing highlights in 2017, although there have been lots really.Love Sewing page 328_09_17_LS_Reader42916I made a third Imogen blouse from fabric I got off The Foldline’s swap table at the first Great British Sewing Bee.

Another favourite top this year was the Merchant & Mills Camber Set which I also got from the King’s Cross meet up in the spring. It’s been a really useful pattern and I love the neat way the binding and the neck yoke finish off the neck edges, it’s a really clever piece of construction.

IMG_3192
neat bias binding on the Camber Set top-my scissors necklace came from the V&A

I also made this top with 1 metre of fabric generously given to us in the Weekender goody bag by Stoff&Stil, it’s Burda 6914 which I’ve used 3 times now although this is the first time as a top. I really like the pleated neckline with a bias binding finish. There was just enough fabric to add slim ruffles to the sleeves which I neatened using the rolled hem finish on my overlocker.

I spent a lot of time during August and September making my entry to The Refashioners 2017, an Alexander McQueen-inspired jacket which I was extremely proud of when I finished it.

Into October and more fabric got purchased at the Autumn Knitting and Stitching Show at Ally Pally (oops) I made my first pair of jeans this month but I can’t talk about them yet as they were a pattern test which still hasn’t been released-I’m really happy with them though so I’ll publish the blog as soon as it’s released into the wide world. (I think the designer needs to get on with it otherwise the whole world will think that Ginger jeans are the only pattern available!)

After literally months of dithering I finally bought a new mannequin, or ‘Doris’ as she’s known to me. Old Doris was falling to bits and only held together by the t-shirt that covered her, I’d had her for well over 30 years so I reckon I’d had good value out of her. I chose the ‘Catwalk’ model from Adjustoform which I bought from Sew Essential and I’ve been very pleased with it. IMG_4038IMG_4039IMG_4040

Also in October I went up to Birmingham for the SewBrum meet up organised by EnglishGirlatHome, Charlotte where I had a really fun day (apart from the sweary drunk woman on the train coming home!) catching up with chums and visiting Guthrie & Ghani for the first time. I took part in the fantastic raffle while I was there but was unsuccessful….or so I thought (again) About 6 weeks after the event I got a message  from Charlotte asking if anyone had told me I’d won a brand new mannequin in the raffle!!! So now I have New Outdoor Doris who lives in Threadquarters and Indoor Doris who lives…indoors, and I use her to take photos on.

November saw another new departure for me when I volunteered to write some reviews of fabric shops in my area. This was for Alex of Sewrendipity as part of her plan to create an unbiased worldwide database of fabric retailers, available to everyone to use. It meant I visited some new places as well as some old favourites.fullsizeoutput_202f

I made another entry for our annual church Christmas Tree festival. It was a refashion/upcycle of the fabric I used for the previous year and sadly it was Old Doris’s last outing before she heads for the tip! The net petticoat was a tube of fabric with the baubles and lights inside it.

I had also volunteered as a pattern reviewer for Jennifer Lauren Vintage so I made a really nice Mayberry dress and wrote a blog for that very recently. One other new pattern I tried out but haven’t blogged yet was the French dart shift by Maven Patterns. It’s a lovely flattering shift dress with a funnel neck and a variety of sleeve styles and no zip. I made it in a navy fabric of unknown origin and wore it on Christmas Day.IMG_4272IMG_4273

IMG_4274
French dart shift dress by Maven patterns.

The biggest deal of the year in some ways was in December when I finally, finally, decided to buy a new sewing machine! This was such a big deal because I’ve had my beloved Elna 7000 for probably 27 years and it’s still going strong (only the occasional hiccough) and I have a strong emotional attachment to it. Thing is, technology moves on and whilst that really isn’t the be-all-and-end-all for me there are processes and functions that I would like in order to keep (even after all these years) on top of my sewing. In early November I went to a fun jeans refashioning workshop hosted by Portia Lawrie and Elisalex (By Hand London) and we were provided with gorgeous Pfaff sewing machines to use. IMG_4092

Anyway, I was thinking about it long and hard for a while because it’s an awful lot of money when I came upon a Black Friday (not even a real thing) deal where this model was virtually half-price. Sooooo, after a visit to Sew Essential a new Pfaff Quilt Ambition 2.0 has come home to live with me and we’re getting to know one another…

IMG_4268
she’s a beauty!

So that just about sums up my sewing year. It’s been a lot of fun at times, and hot and frustrating at others (sweltering under mountainous wedding dresses in the height of the summer is no fun) I’ve met some lovely new people and been reacquainted with lovely ‘old’ ones too! I’m looking forward to another busy year of sewing, blogging, teaching, chatting, tea drinking and generally feeling connected to sewers all over the world. It really feels like dressmaking is an activity that is worthwhile again and not just some strange little hobby that old biddies do, besides, it’s surprising what you could learn from an old biddy, she may just have made the same sewing mistakes as you have but 30 or 40 years earlier!

Happy Sewing

Sue