My latest Minerva make-Tilly’s Tabitha T-shirt dress

I seem to be constantly attracted to teal/turquoise/duck egg shades recently so this Art Gallery organic cotton jersey for my recent Minerva post looked perfect when it hoved into my field of vision! 

I’ve used Art Gallery knit fabrics in the past and the designs and fabric, whilst fairly pricey, are lovely quality. This particular jersey is an organic cotton (with a little Elastane) and very soft, a lighter weight than many so it would be good for children’s and babies clothing as well as adults. I love the print, I think it’s a vaguely ‘Tribal-esque’ graphic stripe and I quickly decided to make a Tabitha T-shirt from Tilly and the Buttons book ‘Make it Simple’ which I’ve made a few times before but to try out the dress hack version for a change this time. 

I traced off a new copy of the pattern using the horizontal lines indicated across the bodice specifically for the dress. I’m not long in the body but I thought it looked a little short so I added an extra 2cms to the bodice length. In truth I probably could have added more than that because I feel there isn’t as much blousing at the waist as there seems to be in the photo in the book [If you know, or suspect, you have a long body length then pay close attention to this before cutting your fabric, get someone to take your nape to waist measurement and compare it to the back pattern piece. If necessary then add any extra through the horizontal ‘lengthen/shorten’ lines, and don’t forget to do the front as well!] If you’re wondering why this matters, it will mean that the waist seam sits too high above your natural waist and could look more like Empire line. 

I followed the instructions in the book to draft my own skirt pattern which was simple enough, you only need one because the front and back are identical (you’ll need a decent sized piece of paper to do this) I cut the new front and back as complete pieces so that I didn’t have to cut anything on the fold, I also wanted a short sleeve so I traced one off. 

The fabric was a little bit curly at the edges so I took my time cutting out, be careful not to pull or drag the fabric at this stage because this could result in twisting of the finished garment. It’s helpful to mark stripes onto the pattern so that you can then match them to corresponding seams more easily. Cutting a single layer of fabric can really help make this more straightforward, and be less wasteful too.

Moving on, the suggestion for the waist casing is to use eyelets or buttonholes. I used a small round-ended buttonhole, whichever method you choose make sure you interface underneath first to stabilise the fabric. I used the quilting guide to help me sew an accurate 2cms seam to create casing. Once I’d sewn it I used a bodkin to thread the ribbon through.

Tiny round-ended buttonholes instead of eyelets
Using the quilting guide to sew an accurate 2cms seam to create the channel
I used a bodkin to thread the ribbon through, this was some tape I used initially until I got the better-matching teal grosgrain ribbon.

The rest of the construction was pretty quick because I already knew the T-shirt in size 5 was a nice fit, the skirt was a bit ‘hippy’ though so I took some off in that area. Following the drafting instructions the pattern piece is shaped for the waist but, for me, a straight rectangle would suffice.

The length was educated guesswork but I’m very happy with it and it’s not too restrictive at the hem, any longer or narrower and the skirt might need a split in it to allow movement. I have the advantage of using a Pfaff coverstitch machine to hem the sleeves and skirt but a twin needle or a zig-zag stitch will do the job too, and don’t forget to use a ballpoint or jersey needle. I used a narrow grosgrain ribbon in a toning teal to slot through the waist casing to complete the dress. As I mentioned near the beginning I might add just a little more length to the bodice next time but otherwise I’m really pleased with this Tabitha dress, it will be comfortable to wear for everyday and easy to roll up in a suitcase if I ever get to go on holiday again!

not keen to reveal pasty white legs!

Minerva provided me with this lovely fabric to write about, I’m delighted with the quality and I’m especially happy with the dress which is so just comfortable.

Until next time, happy sewing

Sue

making the Utility dress by Simple Sew Patterns.

My latest Simple Sew blog make is the fairly recently released Utility Dress, an easy-fitting style with elasticated back waist, drawstring front waist and kimono-shape sleeves. I would say that it’s suitable for softer woven fabrics like chambray, cotton lawn, washed linen or fluid viscose-types, or soft woollens for winter. Having said all of that I chose to make mine in a medium-weight jersey in a tan/black dogtooth check design from Doughty’s Online fabric store. It still works well but you just need to take care not to accidentally stretch some areas such as the neckline in particular and the shoulders. Because of the busy design on this fabric I left out the CF seam and cut the front on a fold instead, thus avoiding any difficult pattern matching down the seam. 

reinforcing the neckline with iron-on interfacing.

I reinforced the neckline using narrow strips of iron-on interfacing I cut myself but you could use the readymade type, I did the same on the front shoulder seams too. You could even use up short lengths of ribbon here for a pretty effect inside. 

As always I deviated from the method of construction a couple of times. After joining the front and back at the shoulders, instead of using ready made bias binding to neaten the neck edge I cut two narrow strips of the jersey which were slightly shorter than the neck edge [the amount will vary depending on how stretchy your fabric is. It’s usually about 85% of the neckline measurement]

Fold them in half lengthwise to form two narrow strips and then place one over the other at a right angle with the folded edges on the ‘inside’ of the V. 

Two narrow strips of fabric, overlapped at a right angle and stitched to hold them in position.

Then reinforce the V on the dress with a row of stitches just within the seam allowance, turning at the V, then carefully snip into the V up to the stitching line.

carefully snip into the V

With right sides together pin the binding to the V section only initially [see the photo to clarify this] and stitch this V section in place by about 5cms either side of the V. Pivot and open the snip as you sew to allow the binding to sit neatly and flat on top of the neck edge. If you’re in any doubt then tack this section first to prevent it moving. 

Attach the V section first, when this is right move on to the rest of the neckband. The pivot point is marked with a purple dot, This is where you rotate the fabric underneath thus opening up the snip you made and enabling the binding edge to match the neck edge.

I pinned on the rest of the neck binding double-checking the length was short enough before sewing the join at the CB. Now you can stitch on the remainder of the band knowing that the V is already sewn accurately. [Thank you Melissa Fehr for this new technique, she uses it in her activewear patterns and I’ve found it gives a nice neat result] Trim and neaten the seam on the inside if required and then you can topstitch it down to prevent the binding rolling.

neckband in position and then topstitched close to the join..

Next I ignored the method for putting the sleeves on. Instead of sewing the side seams up leave them open so that you can open the garment out flat and pin and sew the sleeve strips on more easily.

sleeve band stitched on before sewing up the underarm seam. You can just see that I had pressed the fold line on the sleeve band before I sewed the seam here. This makes it easier to fold once it’s in position. Press the seam towards the sleeve.

Now sew up the side seams including the sleeve bands. Fold the bands up towards the sleeves and either neaten/overlock the raw edge before stitching it down though the stitching line or turn the raw edge under and slip stitch in position. 

neaten the underarm seam before you turn up the sleeve band.

Moving on to the skirt and putting in the hip pockets. I used scraps of matching fabric for the pocket lining as I was concerned that the pattern might show through skirt front. This can reduce bulk too if you’re using a heavier-weight fabric.

pocket bag made with lining scraps

After the pocket bags are complete comes the waistband. I followed the instructions although I think there might be an easier way, I just haven’t worked it out on this version. Although it says there’s a chart to tell you what length to cut the elastic for the back waistband I couldn’t find it anywhere! In the end I decided to cut it half my waist measurement minus about another 6cms, to allow for the stretching and gathering up. I used a length of grosgrain ribbon to go in the front casing. 

I used a zip foot when sewing the waistband to the top of the skirt because I felt it made it less likely that I’d sew accidentally through the ribbon and elastic. 

Joining the waistband containing the ribbon and elastic to the skirt. I’ve used the zipper foot so that I could keep close whilst still making sure I didn’t accidentally sew through the ribbon or elastic. I then neatened this seam on the overlocker.

After joining the top and skirt together all that remains is to hem the skirt. I used a twin needle to do this but you could just turn it up twice and stitch. If you do use jersey fabric for this dress it’s best to sew it with a ballpoint/stretch/jersey needle so that you don’t ladder the fabric as you sew. 

This is a nice comfortable style which I’ll enjoy wearing. Disappointingly there are silly errors again in the instructions which is always so annoying, I hope this won’t be enough to put you off trying this Simple Sew style though which is a bit of a departure from their more usual vintage-style dresses. 

Until next time,

Happy sewing

Sue