Box pleat shirt from Trend Patterns

I’ve made loads of different clothes over the decades but actual shirts for myself have not tended to be among them. I’m not sure why, possibly because I had to wear boring school shirts for years and years, and for a while I had to wear a uniform when I worked for the John Lewis Partnership so my personal preference has tended to softer blouse shapes. That said, I love to see a crisp white shirt especially when it’s given an inventive twist. It’s a wardrobe staple and yet there’s always room for a new version. 

Lucy at Trend Patterns has just released the first 3 patterns of what will become a shirt collection and each is available printed, as a PDF or as a complete kit with pattern, fabric and trims. TPCSH1 is a feminine Pussy bow top with shirt sleeves and a ruffle hem, TPCSH3 has stunning gathered ‘angel’ sleeves which really make a statement whilst the body is kept simple and traditional so that the sleeves do all the talking. 

Lucy offered me the kit of TPCSH2 to try out, it is a box-pleated front shirt, deceptively simple to look at but those details take a little time to get right. It’s classified as ‘moderate/hard’ and I would agree, not because the elements in themselves are especially difficult but each of them needs some experience and precision to execute so I wouldn’t recommend this as your first shirt project. 

The kit comes with enough good quality plain white cotton poplin to make up to the largest size of a UK 22, along with Trend-branded buttons (a nice touch) and iron-on interfacing. All you need to provide is your own thread! 

I started off by taking my measurements and comparing them to the sizing chart, there is also a chart giving you finished garment measurements too which is helpful because it will give you some idea of how oversized the shirt will be when it’s finished. I made a UK 12 and as you will see from the finished photos it’s a very generous fit, to be honest, if you want a close-fitting shirt then this particular pattern won’t be the one for you. 

I opted to trace off the pattern, there are two separate fronts, right and left, and a whole back plus sleeves, yoke, cuffs and collar. There is no pattern piece for the bias binding for the sleeve placket, you just need to cut yourself two bias strips approximately 30cms x 4cms. The right and left fronts are the same except for the extra on the centre front which creates the folded fly with concealed buttonholes. I traced off one front then, to save some time and to ensure they were identical, pinned it to more spot and cross paper before cutting them out together so that I had a mirror version with the additional front added. It’s really important to trace the front very carefully because of the three box pleats, if they are each a bit off you risk the pleats not sewing together accurately which will leave you scratching your head. There are a lot of drill holes to mark the stitching which will eventually hold the pleats in place, don’t be tempted to miss any out because they are also really helpful when you’re folding and pressing the pleats in position. You could choose to trace just half the back to save paper if you intend to always cut it on the fold anyway but having a whole piece gives you the option to have the fabric out flat, besides, it’s almost always more economical to cut fabric out as a single layer [this can be especially helpful if you ever need to do some tricky pattern placement or matching]

Because the fabric is plain, placing the pattern pieces and cutting out was a breeze-no pattern matching, yay! I spent quite a while making traditional tailor’s tacks for every single one of the drill holes. You could use a washable or some other kind of disappearing marker pen if you are confident that it definitely won’t come back to haunt you but I wasn’t going to take the risk on plain white fabric! 

In the past I’ve occasionally found some of the earlier Trend instructions a bit tricky to follow but the more recent ones have illustrations rather than photos and I found this set very clear. My biggest piece of advice would be to read then re-read the instructions before you start, and to highlight anything that you know you’re going to have to really concentrate on, this isn’t a race after all. 

Constructing the fly front and button stand first, including the buttonholes, was satisfying, I often feel like I’ve run out of steam by the end of any project which requires buttonholes and it’s a bit of a chore by then but this gets it out of the way nice and early. [I should add at this point that I started out sewing with a fine size 60 needle so as not to leave too many noticeable puncture holes in the plain fabric if I went wrong or needed to unpick. However, this size needle kept skipping stitches for some reason so I went up to a 70 and had no further problems]

transfer all markings and instructions to the paper pattern if you’re tracing it off. I made tailor’s tacks through every drill hole

My second piece of advice would be to press your pleats on the ironing board if you possibly can. I only have a small heat-resistant board in Threadquarters which meant I was constantly moving the fabric which was not ideal, it was so much easier on the ironing board because the whole piece fitted on. Do not rush this part, with pure cotton fabric you can have the iron on pretty hot but do be careful of your fingers with hot steam. Pin, tack or Wonder Tape the pleats in position once pressed if you want to. 

pressing the pleats on the ironing board, the snips top and bottom along with the tailor’s tacks will help you get each one in exactly the right place.
In progress-making the bar tacks

The instructions are to stitch down each pleat according to the markings using a few stitches. I did quite a lot of testing using a variety of decorative stitches for this before I committed to the bar tack. The next challenge was getting each of those bar tacks (30 in total!) central over the pleat. My machine comes with a number of feet which are used in conjunction with the decorative stitches and one of these has horizontal red lines which proved very helpful in getting lined up for every bar tack. After making a few of these bar tacks I ‘got my eye in’ so I could tell very quickly where to start each stitch, having the needle stopping in the up or down position is an absolute essential feature on my machine for me and it was brilliant during this, being able to lift the foot to check I was sewing in the correct place without the work shifting was so helpful. The photos will hopefully make my method clearer to follow. It’s vital to take your time and be as accurate as possible during this stage because the box-pleats are the USP of this shirt and it will obvious if they are off-kilter. I sewed in white thread but you could use a colour, or even hand embroider to give your shirt a totally original look.

testing various stitches including triple straight stitch and arrow heads, the difficulty was going to getting every single one central over the pleat

Incidentally, Trend will be creating a series of video tutorials to help so I suggest you check their Instagram account or the website for those. Also, there was a slight problem with pattern markings for the back box pleat which were incorrect. This has been rectified but if you bought a copy very soon after release you might find you have to scratch your head a little, the notches were in the wrong places. Check the website if you’re in any doubt.

the right front, including the fly, taking shape
the shirt with the side seams now sewn up, ready for the sleeves to go in
sewing the continuous binding to the sleeve opening. the instructions don’t call for it but I like to sew across the top of it at a 45 degree angle to encourage the binding to stay on the inside
close up of the finished front
all done
close up of the finished bar tacks

I followed the order of construction to complete the shirt (I usually do the first time I make a pattern) but personally I would put the collar on after making the yoke. I like to do it before the side seams are sewn up or the sleeves are inserted, unless there’s a technical reason not to obviously. 

the finished back yoke
I popped a bar tack in the middle of the back to hold the pleat in place, this hadn’t had a proper press yet

Everything came together really well, I’ve always found Trend patterns are accurately drafted so I know the pieces will go together well without major discrepancies-this is why it’s so important to trace off carefully if it’s your preferred method, if seams or notches don’t match up you won’t know where the fault lies [the same applies to accurate cutting out too] 

The sun came out so we could take some outdoor photos, I’ve paired the shirt with my much-worn Megan Nielsen Ash jeans
is it a bird? is it as plane?…
I’ve pressed the pleat now

Clearly not everyone will want to make a shirt that is going to take a sizeable amount of time to construct, or to launder afterwards for that matter, but if we only made simple loungewear for ever then the art and skill of making our own clothes will be lost, just at a time when so many people have discovered, or rediscovered, the joy of sewing for themselves. There will always be a place for a classic white shirt and Trend has created a small but growing collection with original twists on the genre. The last year has been so tough for small business owners so I really appreciate being given this kit to try out, I wasn’t under any obligation to review it other than share some photos but personally I have no problem with sewing and writing about it. I will always try to give you a balanced view and if I can support a little business by giving them some positive exposure then I will. Alongside that I’m keen to demonstrate that a design-led style doesn’t have to beyond us ‘ordinary’ sewers either, if you like it then sew it! 

I hope I’ve given you some idea of what will be involved in making the TPCSH2, if you’re looking to push your skills on a bit this could be a good project. Maybe you need/want a plain white shirt in your wardrobe [amazingly I didn’t have one in mine, just a couple of short-sleeved ones] I might layer this with a sleeveless tank top over it, or a waistcoat could look interesting. This is a typical cotton poplin shirting but you could use a variety of fabrics, you could have fun with graphic prints or stripes, try something soft like double gauze or a crisp linen? Or what about harvesting the fabric from several well-worn mens shirts to make a more patchwork look. Take your time though and enjoy the process.

I’ve got a long-sleeved T-shirt under it because it was a chilly day and it will be perfect for the day I can return to the V&A. I don’t know about you but I’ve really missed putting an outfit together to go on a nice day out, deciding which of the lovely garments I’ve made that I want to wear and how I’m going to accessorise them. It seems such a small silly thing to miss but I shall be so glad when I can start doing it again.

Most of all, thank you to Trend for giving me the opportunity to try the kit, until next time,

Happy Sewing

Sue

Trend Utility trousers TPC12

My first blog of 2021 features my last make of 2020. After several quiet weeks where I didn’t sew any garments, I had cut this project out a couple of months back but then hadn’t felt motivated to make them at the time…the days between Christmas and New Year was the right time to get my head around a nice involved project though. There has been so much going on in the UK recently, (understatement!) especially in these last few weeks, that I wanted something I had to concentrate on to take my mind off other events outside of my control.

If you’ve read my blog in the past you’ll know by now that I’m a big fan of Trend Patterns but these are the first trouser pattern of theirs that I’ve tried.

I saw Lucy wearing her own version of TPC12 on her stand at the Stitch Festival in London back in early March 2020 (just before everything went weird) and it was the unusual split hem detail that initially I really liked. On closer inspection there are some other nice features too, like the topstitched front seams with optional faux pocket flap, and a button fly. These are the kind of details that attract me to a pattern but I would say before I go much further that this is definitely an intermediate pattern as a result, you will need to be a confident sewer or at the very least game to increase and expand the skills you have already. Before I left the show that day I bought some nice heavier weight plain black linen from Rosenberg’s to make them with.

It was then literally months before I decided to tackle the pattern though. I’m not going to lie, and don’t judge me either, but I had piled on weight during lockdown which I wasn’t happy about and as I got bigger the last thing I wanted to do was make a pair of trousers that emphasised that fact. Eventually however I began dealing with the weight issue which in turn encouraged me to revisit the Utility trousers in the early autumn.

Instead of using the linen for the first pair I bought some grey stretch cotton twill from Backstitch near Cambridge. It’s lovely fabric for trousers and a very good quality at a reasonable price. Because the Utility’s are a fixed waistband I went by my waist measurement at that time (it was shrinking!) so I chose the UK 16 and I could tell that the hip would on the big side but that was OK.

I patiently traced off all the pieces which took a while because there are quite a number of unique pattern pieces that need to be cut right side up (RSU) Labelling them all is of paramount importance so that you don’t end up with unusable pieces of fabric cut the wrong way. Once I had cut the fabric out I left all the pattern pieces attached to the fabric until I had either interfaced them or until they were ready to be sewn. I made both my versions exactly (apart from fit alterations) as the pattern but you could leave off the pocket flap detail by cutting a pair of side fronts, or you could have two pocket flaps by doubling up those pieces instead. An advantage of having so many single pattern pieces is that you might have a more economical layplan because they will interlock better, folded fabric is a much less efficient way of cutting out, a single layer just takes a bit longer.

I said at the start that this is an intermediate pattern in my opinion and that is largely because the hem vents and the button fly are quite involved, although not actually difficult, plus I found the instructions and diagrams were a bit tricky to follow. I didn’t go wrong but they do require absolute concentration. What I’ll do in this blog, so that’s useful to you if you decide to make the trousers, is simplify the order of making down to a basic list which you can use in conjunction with the actual instruction booklet. I won’t give you specific, press here, topstitch there, instructions though, they are in the booklet and the diagrams are very detailed.

My first piece of advice, after you’ve attached all the interfacing to the relevant pieces and transferred all markings to the fabric, is to overlock all the cut edges (except the waist and fly front) first. I don’t normally do this because I prefer to overlock as I go along but it makes more sense here to do it as a batch process, just make sure you don’t trim away too much or lose your notches in the process.

Start by making the ‘pocket’ flap [make up the optional pocket bag if you are going to have one but set it aside for the moment] also, make the back darts and set the pieces aside for now.

Join the front seams for both fronts as far as the vent markers, do not join the fronts to the backs just yet. I found it easier to have only the vent sections to work on flat first although the instructions tell you to join the fronts to the backs. Once you’ve made both the vents except for the final single topstitching to hold the flap in place and are ready to turn up the hem join the fronts and backs at the side seams first. Now complete the topstitching to hold the vent in place then join the inseams, turn up the hem and topstitch to finish. [If you’re using the additional pocket bag I would add it whilst the leg is still open and flat, before sewing up the inseam. I sewed mine on earlier and it got in the way a bit when I was joining the various leg seams]

Pin and partially stitch the crotch seam as per the instructions then apply the outer waistband and press the seam up towards the waistband. [If you want to include belt carriers I would add them before attaching this waistband so that they are caught in the waist seam, the tops of the carriers will be enclosed when you add the facing]

Next, make the right fly section and buttonholes as per the instructions and diagrams. I’ve included a photo of where I stitched through the layers of the right front to hold them all together, I’m not sure if this is quite what is intended but it works-I couldn’t make sense of it otherwise!

the pencil is pointing to where I’ve added the row of stitching to keep the layers together.

Make the left fly front and attach the waist band facing, I’ve included the photo below of how this should look from the inside (yes I did use jazzy overlocking thread just because…)

the completed grey version showing the button fly and jigger button

Sew the remainder of the crotch seam to complete it, then sew the entire crotch seam again about 1-2mm away from the first stitching line.

Sink stitching-to complete the waistband-is simply the industry term for ‘stitch in the ditch’.

Obviously there are points where you would be advised to try the trousers on to check the fit as you go so you could do this by pinning on the stitching line (parallel, not at a right angle!) to avoid unpicking. The advantage of having a split waistband on the centre back seam (like good quality men’s trousers) is that you can fit into the small of the back more effectively.

So that’s, hopefully, a simplified method for you, it isn’t that I think the instructions aren’t good, it’s just that I got a bit confused between what was written and which diagram to follow, and that’s why I wrote it down in a clarified form as I made the second pair.

The fit of the first pair is technically not that good but they are soooo comfortable. The waist was a good fit initially although I’ve lost more weight since then so it’s very roomy now. The major issue (and I’ve read this in a few reviews) is that the crotch length is very long and looks quite droopy. You can see this in the photos of my grey pair, and this makes the cropped leg length look a bit too long as a result. For the second pair in the black linen I redrew the pattern down one size and also folded out 3cms horizontally at hip level on every pattern piece to reduce the rise. The second pair are a much better fit but that won’t stop me wearing the grey pair, it doesn’t particularly bother me that they are overly generous because the shaped waistband can’t fall off my hips anyway. Yes the grey pair are very baggy but that’s fine.

The black linen pair are a better fit at the waist, there’s still plenty of room (too much room?) over the thighs but I don’t mind that. Maybe I’ll shave a little off the next pair, or maybe I won’t…

Overall I’m a big fan of the Utility trousers and I’ll probably make more, now that I’m getting better with the fit. The design details are worth the effort but it is a project you’ll want to take some time over, I had to turn off the radio so that I could concentrate completely and I read aloud each instruction several times to ensure I was going the right way. I sewed matching topstitching but you could use a contrast thread, or maybe you could line the waistband and button stand with contrast fabrics? Apart from the pocket bag if you add one there are no other pockets so you could add some in the side seams quite easily I would have thought, or patch pockets on the back perhaps? I quite fancy a pair made in chunky cord too…

I hope you find this useful, or I’m happy to try and help if I can.

Until next time, happy sewing

Sue

Simple Sew Chelsea Collection blouse hack.

A lot has happened since I wrote my last Simple Sew blog post, Christmas for one thing, and I had a lovely holiday in the sunshine too but now we are all confined to our homes because of Covid 19. Without wishing to trivialise the gravity of this situation, one of the side effects of it is that you might have more time to sew. 

I’ve had a rummage through my Simple Sew patterns to find one which I haven’t already shown you, and which has opportunities to hack, and I settled on the Chelsea Collection. This is a capsule wardrobe of a short sleeve blouse with two variations, a pair of trousers and a button-front skirt in two lengths. I liked the blouse with it’s shirred sleeves and keyhole back detail but I decided to mix it up a little by adding a button front. Normally we are able to select fabric from a couple of generous sponsors but I wanted to ‘shop my stash’ to find something this time. I found a very pretty vibrant floral John Kaldor cotton lawn which I think I picked up from a swap table sometime and I knew would work well for the blouse. 

I didn’t want the blouse to be overly tight so, after checking my measurements I opted for a larger size than I’ve made previously. If you’ve been a regular reader of my posts you’ll know that I tend to check Simple Sew patterns for any discrepancies before I start. There didn’t seem to be any glaring ones but I just added a slight curve to the back hem so that it dipped in the same way as the front and I trued the shoulder seams so there was a smooth flow from front to back. 

Adding a curved hem to the back, I measured the distance from the lengthen/shorten line on the front then made the back the same amount, curving the line gently upwards to the side seam.
trueing the shoulder seams

As I wanted to alter the front significantly I had to make some changes there first. In order to create a button-stand I simply added 2.5cms to the centre front all the way down what would have been the fold. [2.5cms was a fairly arbitrary figure because it depends really on what size buttons you’re using, a general rule of thumb is that the bigger the button the bigger the button-stand needs to be so that there’s enough overlap and the garment doesn’t end up too tight because the overlap isn’t big enough.]I was able to do this by drawing directly onto the tissue before cutting the piece out as there was enough space to do so.

adding the button stand to the front

If you’ve already cut a pattern that you want to add to just stick some extra paper to the centre front fold line, or trace off the whole piece again adding the extra. The original front had a facing for the neckline so now I needed to create a new facing which would neaten both the neck edge and the button-stand. To do this I simply traced off the whole of the new front opening including the neck edge and made the facing a depth of 7cms all the way down from shoulder to hem, with a smooth and gradual curve. The photo should make this clearer. The back neck needed a new facing too because the existing one took the armhole into account. Again I traced off the section I needed making it 7cms at the shoulders to match the front facing. 

The final change I made was to lengthen the sleeve a little and add some more fullness to it. I started by making the sleeve 5cms longer and then I drew 3 vertical lines on the pattern at approximately the front notch, back notch and shoulder seam points. [Depending how much extra fullness you want to add to a sleeve you could use more places than this but do try to space them evenly apart.] Next I cut up each line from the bottom until I reached almost the top, I left this very slightly attached. With the piece flat on the table I spread the bottom of each slit by about the same amount, probably about 4 cms, then taped slithers of paper into each gap.

First I added the extra length and then drew the vertical lines where I wanted the extra fullness.
Next I opened each part to add the extra being careful to keep the pieces flat and not twisting or wrinkling up, put extra pieces of paper under the gaps. Once you’re happy tape them in position,
Once I had added the extra I cut the piece out.

If you don’t want to cut the pattern up you can do the same process by still marking the vertical lines on then pivoting the uncut pattern at the top of each line, use a pencil or your finger as the axis. Draw or trace around the first section, which remains stationary, then each subsequent section after you pivot it to so that you get the extra fullness being added at the hem. Opening up the wedges in this way means you’re adding fullness to the hem but not the crown of the sleeve, if you want extra fullness in the crown spread the whole piece more or less parallel. The grainline should run equidistant down the centre of the new piece (unless you want to cut it on the bias)

Having done all this I cut it out and was ready to sew! 

I started by joining the shoulder seams of both the blouse and the facings (which I’d interfaced and neatened) then I attached the facings to the neck edge, turned, understitched and pressed. The keyhole back calls for a small rouleau tube as a button-loop which needs to be inserted at the same time as applying the facing although you could choose to make a hand sewn thread loop and stitch that at the end. In fact it isn’t even vital that this is a functioning loop if you’ve got a front opening, the keyhole is purely decorative now. 

I put the blouse onto Doris to check it was looking OK and this was when I found that the keyhole appeared to be bagging outwards quite significantly. I decided not to do anything at this point and I would check again once I had sewed the side seams and put the sleeves in, then I would get a better idea by trying it on myself. 

Checking the front neck
With the loop pinned I discovered that the keyhole didn’t sit flat.
It seems to stick out quite significantly on Doris.
If the button isn’t done up it would look like this.

I made three rows of shirring on the sleeves next, using my quilting guide to make sure the first row was 5cms from the bottom edge, the next two rows were then sewn parallel to the first. [Refer to a previous blog post on how to sew shirring if you haven’t done so before] Next I sewed up the sleeve seams and pin-hemmed the bottom edge to give a neat finish.

I positioned the needle 5cms from the cut edge and the quilting guide helps me as a visual marker to keep it parallel all the way.
Shirring is stitched from the right side so that the elastic is on the reverse. Use a long straight stitch, secure both ends and then apply plenty of steam to shrink up the stitching further.
finished sleeve

After sewing up and neatening the side seams I inserted the sleeves. At this point I tried the blouse on again to check the keyhole on myself and, with real shoulder blades under it, it didn’t seem so noticeable. Two other things struck me though, the blouse was a little too big so I took it in on the side seams and also the blouse was a bit shorter than I expected. In order to take as a small a hem as possible I made some bias binding from offcuts of the fabric then stitched it (folded in half lengthways and with the cut edges together) to the hem using a narrow 5mm seam allowance [This is a useful finish to any hem or edge where you need every spare centimetre of fabric.] Have a look at the photo which shows you how to get the ends of the binding enclosed within the front facing. I turned the binding up and top-stitched in place. 

If you’re adding binding when there’s also a facing pin it like this so that the end is neatly enclosed inside the facing when it’s turned right side out.

Finally, I found some ‘vintage’ buttons amongst my treasure trove and there were just the right number meaning the whole blouse had been sourced from what I already have!

Well I hope now that I’ve made it that I’ll have a chance to wear my Chelsea blouse somewhere other than in my own garden this summer, who knows? Maybe you’re reading this long after the emergency ended and life has returned to some sort of normality, although it definitely won’t be exactly as it was before.

Sewing our own clothes is an activity which gives us so much enjoyment for a variety of different reasons and, right now, the simple act of creating something is chief amongst them for me. It’s absorbing and the problem-solving gives me something else to think about.

I think the keyhole back is, by and large, just about acceptable when I’m wearing the blouse. I also think the cure could be to add a centre back seam instead of cutting on the fold so that the point of the keyhole could extend beyond the centre back line, this would hopefully bring the button and loop closer to one another when they are done up…this is just my theory based on experience and I haven’t tried it out. It’s such a nice little detail that I’m disappointed it hasn’t worked out quite right. I also regret not reading my fellow Simple Sew bloggers reviews of the blouse because then I would have known how short it comes up, personally I would add a minimum of 8-10cms to the length next time.

The sleeves are pretty and feminine but maybe they are a little too girly, the jury is out…

Until next time, happy sewing

Sue

Testing the Regatta dress from Alice & Co

Alice & Co are a pattern company run by the mother-and-daughter team of designer, pattern cutter and sewing teacher Alice, and Lilia, who is a museum textile conservator for her ‘day job’. I saw they were requesting new testers for one of their latest patterns and, as I generally enjoy the process of testing and I’m happy to give my time to assist small indie companies when possible, I was pleased to be invited to help.

The Regatta is a summer dress featuring a neckline which pulls up with ribbon to tie on the shoulders, a gathered or pleated waist, patch pockets and a button-back closure.

I had some printed viscose fabric in my stash which my good friend Claire had given me a few months back and I was sure it would be ideal for this test version of Regatta. I think the dress will be great made in a wide variety of fabrics including chambray, cotton poplin, madras cotton check, seersucker or shirting, as well as eyelet or broderie anglaise, washed linen…I could go on!

This is a PDF pattern but unlike many which provide you with ALL the pattern pieces you might require, because of the simplicity of the skirt it only gives you pieces for front and back bodice plus a patch pocket. It needs a total of 8 pages printed in colour rather a selection of dotted/dashed lines. The skirt is merely three rectangles (front and two backs) so rather than waste paper it gives you guidelines to follow for cutting the skirt pieces ‘freehand’. This isn’t as daunting as it might sound, I used the full width of the fabric cut to my chosen length PLUS a hem and a top seam allowance and then the same again but cut into two equal pieces to form the backs.

The instruction booklet is written in a nice friendly chatty style which feels both informative and encouraging, I think the illustrations are well-drawn and clear too. I printed mine out in booklet format which is a good option if your printer will allow it, 3 pages printed on both sides which fold neatly into A5.

I opted to cut a size 16 according to my measurements from the chart but I would definitely come down at least a size for the next one. As the bodice needs to be lined anyway you could make up the lining as a toile to see if you need to make any adjustments and then use it in the dress. Depending on your fabric you could self-line it or, as I did, use a plain cotton. I also decided at this stage that I would line the skirt because my fabric is a bit sheer, plus it’s a floaty skirt so I don’t want any knicker-revealing moments on windy days!! [I made a simple A-line lining, not the full pleated skirt which would have been awfully bulky]

The bodice construction is simple [if you don’t like darts you won’t be a fan though, you’ll need to make 8!]

Follow the instructions carefully for the ribbon channel openings, the diagrams will help if you’re not sure. Take care inserting the ribbons pieces at the back-cut the ribbon into one long piece for the front and two shorter pieces for the backs. You could possibly use wide elastic for this element instead if you want a different look, or make a self-fabric strip or what about using a vintage scarf even?

Once you’ve joined the outer fabric and linings together along the neck edges and armholes you’ll also need to understitch here as much as possible, to give it a nice crisp edge and stop it rolling. Just go carefully so as not to catch the fabric accidentally-you won’t be able to sew everything because it will be inaccessible in places. 

Next, when you sew the actual channels that the ribbons sit in, it might be wise to tack in position first, certainly mark the lines in some way-chalk, pencil, erasable marker-or if you have a quilting guide attachment for your machine use that. It looks like a piece of bent metal which slots in behind the foot of your machine. You can see it better in the photo although this was a different project. This enables you to follow a stitching line which is considerably further away than your usual seam allowance markings on the needle plate will allow. You’ll need to be most careful sewing the back channels because the ribbon is already in position so don’t sew through it by accident, it won’t gather up. Slot the ribbon through the front when you’ve sewn the front channel, or leave it until you’re ready to try the dress on and adjust the bows to your taste at the end.

using the quilting guide attachment to follow a wider width [this was on the Heron dress]

Making up the skirt is simple enough, don’t forget to interface the button-stand areas for stability. The pockets are positioned over the side seams but they could go directly on the front if you prefer.

I opted to use pleats on the skirt because I prefer how they look on me to gathers. I don’t have any sage advice or foolproof mathematical equation for working this out I’m afraid, I just pinned the skirt to the bodice at the side seams, CF and CB button-stand and then fiddled until I was happy with the pleats before stitching it on. There were lots of pins involved!  

lots of pins holding the pleats in position ready to sew.

If you aren’t lining the skirt then you can simply slip stitch the lining in place by hand as per the instructions. As I was lining the skirt too I cut, sewed and hemmed a simple A-line shape in plain cotton which I stitched to the bottom of the bodice lining, obviously it must have the gap at the back for the button opening. I simply caught this down behind the button-stand with a few hand stitches so it doesn’t flap about. So that it doesn’t ride up inside the dress I hand-sewed a few stitches at the side seams and CF where the seams meet to anchor them together loosely.

The lining looks like this inside, it doesn’t need to be the full length of the skirt although it could be if you want.

I used a nice deep hem of 5cms to give the skirt weight. I overlocked the edge and then used the blindhem stitch and foot to sew it up. As the hem is straight you could face it instead with bias binding or ribbon, or a contrast fabric for a different look, either machine top stitch or slip-hem in place by hand. The photos show the blindhem for my machine but most machine manuals will show you how to sew this-definitely practice to get it right as there is a knack to it.

I used 4 buttons on the bodice section and then 6 buttons on the skirt, evenly spaced so that there’s still a nice ‘split’ at the bottom. I have a ‘thing’ about button opening on skirts where the bottom button is too close to the hem, don’t ask me why, I just don’t find it aesthetically pleasing. For a novel detail I used red and blue thread to sew on the bodice buttons and ivory on the skirt. I also added a small hook and eye at the waist seam to take any strain off the button at this point. 

All that remains is to pop your dress on and pull up the ribbons to your desired amount and tie in a bow, trim the ends into neat Vs to stop them fraying. Once you’ve adjusted the gathers to your liking then pin and stitch in a few places as per the instructions to hold them in place evenly.  

I used green Grosgrain ribbon as a contrast to the otherwise nautical colours of my Regatta dress.

I just need to find a nice wide belt to finish it off I think although it works perfectly well without. My Regatta dress has already had two wears since I finished it and it’s quirky details make it stand out. It isn’t an ultra-quick make compared to some styles but it’s worth the effort and makes a charming and feminine summer dress. It would even work in more ’special’ type fabrics too, like panne velvet, Chantilly lace or crepe de chine for an evening or party dress.

Once again it’s been an interesting process to help test a pattern and Alice & Co were quick to respond to queries. Another reason I was keen to assist is because as a brand they are very supportive of the Sew Over 50 cause by reposting images shared by older makers using their patterns, and have generously provided prizes in our previous challenges.

So while the sun is out here in the UK this could be a nice addition to your summer/holiday wardrobe.

Until next time,

Happy sewing

Sue

A Grainline ‘Alder’ shirtdress with sleeves

img_0340

I’ve already made one Alder earlier in the summer and liked wearing it more than I expected to…a slightly bizarre statement surely?  I loved the fabric, a cute butterfly-print poplin bought from Backstitch in the spring, and I like the style a lot but it felt a bit snug over the bust (and I’m not large) and I couldn’t get the collar to go on the neatly. This may have been because I forgot halfway through (or never actually checked) that the seam allowances are 1/2″ which isn’t a typical SA for most patterns sold in the UK. If I used 1.5cms this would explain why it was a bit tight. Rookie error!

img_4575
Sorry about the messy hair-I was on holiday!

img_0349
I made view A again.

I added a box pleat to the back this time to create a little extra fullness, as well as it being a new detail. This is simple to do. Instead of placing the pattern piece directly against the fold of the fabric just move it parallel away from the fold by the amount you want, I moved it by 2cms which added a total of 4cms. [If you don’t want fullness all the way to the hem, place the hem against the fold and pivot the pattern piece from that point away from the fold at the top by as much as you want to add] Then you can pleat out the extra as you wish, I top-stitched it down, western-shirt style.

img_0342
This is what it looks like finished

I decided exploit the distinct pile of the fabric by cutting the patch pockets on the bias. It was pretty straightforward from then on to make up the dress, I was really careful about the seam allowance this time.

img_0341
pockets cut on the bias and saddle stitched

I top-stitched most of the seams using the saddle stitch setting on my machine [it looks like 3 lines of stitches side by side in the diagram if you’ve got it, it oversews each stitch so they’re highlighted more than if you just did one row of normal stitch in regular thread]

img_0345
This time the collar went on just fine, I must have goofed somewhere on the previous one.

In the end I decided not to make it sleeveless as before so I added sleeves from a Simplicity pattern I’d used previously. I checked the arm scye measurement against the sleeve head to ensure the sleeve was big enough, but not too big, to go into the armhole. This sleeve has a simple cuff without a placket so it was speedier to make and not too bulky in the cord fabric.

img_0343
Finished cuffs, I haven’t top stitched them although I might…so indecisive

I should mention that I’ve also added pockets to the side seams this time-always handy for a tissue to go through the washing machine and cover everything in white fluff!img_0346

Considering I have about 4 billion buttons in my collection I was somewhat surprised to not be able to collect together enough buttons all the same! So….there are two different-coloured ones on the front and perfectly matching red ones on the cuffs, a quirky detail I like to think.

img_0344
You’ll notice it’s been hard to capture the colour of this.

And there we have it, it needs a bit more of a press judging by this photo but I think it will be a lovely cosy winter dress with thick tights or leggings, and boots. The pile on plain cord gives lots of different shades even when it’s all cut in the same direction as this was.img_0418

…and there’s still a bit of fabric left too, perhaps I’ll keep that another 23 years and make something for my yet-to-be-born grandchildren!

Happy Sewing,

Sue xx