Trying out a new Simplicity patterns PDF

Simplicity have long been one of the most familiar big names in the home sewing paper patterns market but many of us are now choosing to use PDF patterns instead for a variety of reasons. Simplicity have recently decided to dip a toe into the waters and release a small collection of patterns as PDFs for the first time.

I was first invited to try one of this new range of PDF patterns way back in high summer but for a variety of reasons it’s taken until mid-October to get completed. 

Simplicity have released a range of ten basics which are available now from Sew Direct including several tops, a skirt, a dress and a jumpsuit, plus two children’s patterns and a free clutch bag pattern. 

I chose the tie-front robe jacket SP110 which appealed to me as a cover-up in place of a cardi or sweatshirt and, because it was July at the time, I picked a pretty, drapey Atelier Brunette viscose crepe in a pale ivory print kindly provided by Minerva. The robe jacket is a very simple silhouette with a wide grown-on 3/4 length sleeve, the neck is finished with a band and the tie waist is elasticated across the back.

For me, it depends how many pages a PDF has whether I print it myself or send it away (my usual cut-off is anything over 30 sheets, more than that and I’m not keen on the printing and assembling) However, we had been experiencing postal strikes here in the UK and I needed to get started so I printed at home this time. I think the paper in my printer was a bit out of alignment because not all the pages were printing as accurately as they should have been but fortunately I could see what had gone adrift as I assembled the pages and was able to rectify it. Make sure you print the test page and check carefully that all borders are present and accurate, don’t simply check the test square measurement and wander off into another room while it’s all printing out… With A0 printing this shouldn’t be an issue.

The pattern includes all sizes from UK6 to UK26 (up to 48” bust) which are broken down into two size bands (there isn’t a layering option to isolate which sizes you choose to print unfortunately) The robe jacket consists of just six simple pattern pieces.

The instructions sheet/booklet design is attractive and uncluttered with clear diagrams and straightforward step by step instructions. For the more novice sewer there is a glossary which includes all the sewing terms that will be used throughout, and a page explaining pattern markings. This being a US-originated pattern, all the seam allowances are only in inches so you may want to write your own metric equivalents on the page somewhere before you start, to avoid confusion. 

snipping the curved underarm seam means it sits more smoothly without puckering when it’s turned through

pulling up the gathering stitches

turning through the front ties using my old school ruler!

I joined two pieces of elastic using the 3-step ‘elastic’ stitch on my machine.

two different methods of pulling the elastic through, either using a bodkin or using a safety pin with a piece of masking tape to prevent it from opening accidentally inside the channel.

All finished

This is a quick and easy make, not much more than half a day probably, and everything comes together well. I thought the instructions and diagrams were clear, well explained and thorough without being over-complex. Overall a relative beginner should be able to manage this pattern. I like to print my instructions in booklet form but I should have increased the font size a little as I struggled occasionally to see the diagrams. I think the diagrams are actually very good, I simply didn’t print them large enough. If you are reading them from a tablet or lap top then this isn’t so likely to be an issue.

My only ‘problem’ now is that I have a summer garment as we head into autumn/winter. I intended it to be a light cover over summer dresses and tops so I’ve tried to style it for the season as it is now. I made a UK14 but possibly should have gone up a size, I feel self-conscious about how it looks around my midriff. It falls exactly on my natural waistline (I’m 5’5” tall) rather than above it like the models who are probably 5’8”-5’10” minimum. Hey ho, I didn’t get the tall gene but I did get the yoyo weight one instead! Basically, I’m pleased with the garment overall but less pleased with how it looks on me just now. I’m determined to get use out of it though but it will probably not be much before next spring. 

Wearing it with Vogue Marcy Tilton #8499

and with a newly finished pair of wide-legged Eve trousers by Merchant and Mills

And finally with my recent Nina Lee Portobello trousers and a vintage shirt pattern from around 1978!

I have a small quantity of the fabric left so, if there’s enough, I may consider adding it to the bottom under the waistband. This shouldn’t be too difficult because the waistband is straight and it would then give a little peplum which I might feel more comfortable with. It wouldn’t be too difficult to add a longer skirt to turn it into a coat as an alternative.

Being a PDF means you can buy the pattern to use immediately, and all the others in the Simplicity PDF range from Sew Direct. I was paid a modest fee for my pattern review and generously provided with the fabric to make it from Minerva. All views expressed are of course my own. 

Until next time, happy sewing

Sue

Tips for sewing with linen jersey, a new Lamazi post

Did you know that linen jersey was even a thing? It’s an unusual fabric which you don’t see often, we all know knits are available in most other fibre types-cotton, wool, silk or man-mades for example- but I’ve never worked with it before so when Liana invited me to sew my next Lamazi project using it, and to pass on any hints and tips for sewing it, I was up for the challenge. 

This 100% linen jersey comes from Mind the Maker in a range of colours and I picked the Dry Mustard shade which is a lovely vibrant ochre. The fabric has a beautiful lustrous sheen on the right side, the reverse is duller so it makes it much easier to tell the difference between the two. It has lovely light drapey quality too and is slightly sheer.

Linen fabric is not a textile known for its inherent stretch qualities and this jersey does feel slightly different from other knits because it has only a small amount of stretch along its length and quite a lot of stretch across the width but it has very little recovery so once it’s been stretched out it will stay like that at least until it’s washed again. During construction the application of plenty of steam will encourage some of this accidental stretching to be eased back into position so, coupled with its sheerness, this means that you need to think carefully about what garment to sew with it. 

Plenty of steam will help remove most unwanted bagginess like this

The properties of linen fabric itself [cool in warm weather, warm in cold weather] mean that it would be ideal for loose-fitting leisure or exercise wear, for yoga or Pilates for example. I would definitely say it’s better to avoid anything that is particularly close fitting because areas like the elbows or wrists would become stretched or baggy with little recovery. However the fabric has a lovely drape and its fine gauge allows it to be gathered up successfully so these properties could be exploited instead.

Bearing all these factors in mind I decided to make (another) Sewing Revival Heron dress which I would hack into a blouse. The pattern has a neckline which is gathered using elastic along with raglan sleeves with deep elasticated cuffs. To mix it up further I decided to pull the hemline in onto elastic rather than have a wide smock silhouette.

First things first, I washed the fabric by hand to remove any risk of excessive shrinkage or twisting in the machine. If you want to wash it in the machine then it might be an idea to overlock the cut ends together first to form a long loop and place it into a large washing bag to protect it further. Alternatively you could press it on your ironing board with plenty of steam instead. If at all possible it is better to dry the fabric flat, and certainly don’t wring or twist it. All of this might sound off-putting, and it is clearly not as straightforward as chucking a nice stable cotton into the machine but this is a luxurious fabric and deserves to be treated and handled carefully in the preparation. When it comes to cutting out your pattern pieces lay the fabric as flat as possible, handle it gently and don’t pull it about too much, especially if you decide to fold it. I made a whole back pattern piece for my top so that I could cut it flat, another appeal of the Heron pattern for me is that it has just three pieces so it’s a relatively quick sew usually. 

After cutting all the pieces the first thing I did was stabilise all the raglan shoulder seams using some iron-on seam tape, I did this to prevent any unwanted stretching before I sewed the sleeves in later on. I added small squares of iron-on interfacing to reinforce the bottom of the opening on the centre front seam too. I also decided to press all the folded parts of the casings/ruffles for the neckline, sleeves and hem before sewing anything together, just so that I was handling the cut-out pieces as little as possible, again to prevent unwanted stretching before they got joined together. I also tacked these folded parts into position temporarily. All this might sound excessive but I wasn’t in a rush, and I found the slow and considered processes very soothing at quite a difficult time. 

iron-on stay tape to prevent unwanted stretching of the raglan seams

• 

  the pinned raglan seams showing the slight excess to be absorbed

• 

  the finished seams inside the garment

I pressed and tacked casing/ruffles before joining the sections together later on

reinforcing the bottom of the neck opening with small squares of iron-on interfacing.

Something else I did before commencing was check on fabric scraps which needle and stitch-type would give me the best results. A ballpoint needle suitable for stretch/knits/jersey is essential to prevent snagging which could lead to laddering of this delicate fabric, and I found a short straight stitch was better than a narrow zigzag but you must do what works best on your own machine. You could sew a garment together entirely on an overlocker but be aware of the lack of rebound this fabric has so if it gets stretched or misshapen while it’s being sewn then it’s probably like that permanently. I also tested the overlocker finish before diving in for the same reasons. If you don’t have an overlocker this fabric is fine enough that where possible you could probably sew self-neatening French seams, or a wide zigzag might work but just be careful it doesn’t chew up the edges. If you have an overlock stitch option on your sewing machine and/or a special foot to sew an overlock-style stitch then definitely use them. Test all options before making your choice, the time taken could save you upsets later on. I slipped some folded strips of paper underneath the seam allowances when I pressed them to minimise any chance of the seam showing through on the front

testing stitches and overlocking

I popped two strips of folded paper under the centre front seam while I pressed it so that there was no show-through or unwanted shininess on the right side.

If you have a walking foot for your machine this is definitely a fabric worth using it for, even if you don’t it’s a good idea to use plenty of pins. I’m not a fan of mini-clips because I think they are too heavy and get in the way, this fabric is lightweight and I think mini-clips could distort it while you’re sewing but it’s up to you. Tacking seams is always an option too of course, any technique that prevents the fabric shifting while you sew basically.

If you’ve followed my blog for a while you’ll know I’ve made a few Herons before so the construction was straightforward, the only area I did differently was to create the ruffled hem with a wide elastic casing. I couldn’t decide between my planned 2cms or 1cm wide elastic initially so I tested with the two widths to see which I preferred-I chose to stay with the 2cms width as planned. 

testing which elastic width I preferred for the hem, this was the narrow one (the fabric scrap is wrong side out!)

and this is wider width, it’s the one I used at the hem in the end.

using a bodkin to insert the narrow elastic in the neck casing.

checking the gathered neckline on the stand

I used this quilting attachment on my machine so that I sewed an accurate parallel width for the elastic casing

close up of the elasticated hem casing

To sum up, I’m really pleased with how my first experience of sewing with linen jersey has gone, I’ll admit I was a little nervous because Liana was putting her trust in me with an expensive fabric but taking the time to plan and test, and use my existing knowledge of working with knits definitely helped. Because of the sheerness of the fabric Lamazi also provided me with a metre of Atelier Brunette crepe viscose in Ochre to make a camisole to wear underneath, I used the Simone camisole and trousers pattern by Maven which is a very quick make and a very useful garment to wear on its own or underneath other garments. The crepe viscose is a beautiful quality fabric with lovely handle and drape but be aware that there’s a disappointing amount of creasing, you might want to take that into account when planning, for example if you’re making something you’ll spend a lot of time sitting in.

all finished

As always, I hope you find my hints and tips helpful if you choose this lovely fabric, I wouldn’t recommend it to a novice sewer because some experience of sewing with other similar fabrics is definitely an advantage, plus it would be shame to end up with a costly mistake, but if you’re looking for a new challenge to add to your repertoire this could be a good start. I’ll launder the finished garment either by hand or in a wash bag on a gentle cycle in the machine. I’ll dry it flat too and store it that way, I don’t want a coat hanger to make it misshapen. If you’re a person who prefers not to worry too much about their clothes or their maintenance then this might strike you as overkill, and that’s fair enough, but I don’t think it hurts to have a few special things in our wardrobes which were worth the effort to make for ourselves. 

I’m looking forward to wearing this top as autumn is fast approaching (did summer ever arrive!?) thank you to Lamazi for providing me with the fabric to review.

Until next time, happy sewing,

Sue

My latest Minerva make-Tilly’s Tabitha T-shirt dress

I seem to be constantly attracted to teal/turquoise/duck egg shades recently so this Art Gallery organic cotton jersey for my recent Minerva post looked perfect when it hoved into my field of vision! 

I’ve used Art Gallery knit fabrics in the past and the designs and fabric, whilst fairly pricey, are lovely quality. This particular jersey is an organic cotton (with a little Elastane) and very soft, a lighter weight than many so it would be good for children’s and babies clothing as well as adults. I love the print, I think it’s a vaguely ‘Tribal-esque’ graphic stripe and I quickly decided to make a Tabitha T-shirt from Tilly and the Buttons book ‘Make it Simple’ which I’ve made a few times before but to try out the dress hack version for a change this time. 

• 

• 

I traced off a new copy of the pattern using the horizontal lines indicated across the bodice specifically for the dress. I’m not long in the body but I thought it looked a little short so I added an extra 2cms to the bodice length. In truth I probably could have added more than that because I feel there isn’t as much blousing at the waist as there seems to be in the photo in the book [If you know, or suspect, you have a long body length then pay close attention to this before cutting your fabric, get someone to take your nape to waist measurement and compare it to the back pattern piece. If necessary then add any extra through the horizontal ‘lengthen/shorten’ lines, and don’t forget to do the front as well!] If you’re wondering why this matters, it will mean that the waist seam sits too high above your natural waist and could look more like Empire line. 

I followed the instructions in the book to draft my own skirt pattern which was simple enough, you only need one because the front and back are identical (you’ll need a decent sized piece of paper to do this) I cut the new front and back as complete pieces so that I didn’t have to cut anything on the fold, I also wanted a short sleeve so I traced one off. 

The fabric was a little bit curly at the edges so I took my time cutting out, be careful not to pull or drag the fabric at this stage because this could result in twisting of the finished garment. It’s helpful to mark stripes onto the pattern so that you can then match them to corresponding seams more easily. Cutting a single layer of fabric can really help make this more straightforward, and be less wasteful too.

Moving on, the suggestion for the waist casing is to use eyelets or buttonholes. I used a small round-ended buttonhole, whichever method you choose make sure you interface underneath first to stabilise the fabric. I used the quilting guide to help me sew an accurate 2cms seam to create casing. Once I’d sewn it I used a bodkin to thread the ribbon through.

Tiny round-ended buttonholes instead of eyelets

Using the quilting guide to sew an accurate 2cms seam to create the channel

I used a bodkin to thread the ribbon through, this was some tape I used initially until I got the better-matching teal grosgrain ribbon.

• 

• 

The rest of the construction was pretty quick because I already knew the T-shirt in size 5 was a nice fit, the skirt was a bit ‘hippy’ though so I took some off in that area. Following the drafting instructions the pattern piece is shaped for the waist but, for me, a straight rectangle would suffice.

The length was educated guesswork but I’m very happy with it and it’s not too restrictive at the hem, any longer or narrower and the skirt might need a split in it to allow movement. I have the advantage of using a Pfaff coverstitch machine to hem the sleeves and skirt but a twin needle or a zig-zag stitch will do the job too, and don’t forget to use a ballpoint or jersey needle. I used a narrow grosgrain ribbon in a toning teal to slot through the waist casing to complete the dress. As I mentioned near the beginning I might add just a little more length to the bodice next time but otherwise I’m really pleased with this Tabitha dress, it will be comfortable to wear for everyday and easy to roll up in a suitcase if I ever get to go on holiday again!

not keen to reveal pasty white legs!

Minerva provided me with this lovely fabric to write about, I’m delighted with the quality and I’m especially happy with the dress which is so just comfortable.

Until next time, happy sewing

Sue