Considering it’s a raincoat this is a project that came out of a clear blue sky! In other words, I had no plan to make a raincoat until, that is, I spied this gorgeous showerproof Missoni fabric on Dibs’s Selvedges and Bolts website. I’m not normally a sucker for impulse purchases of online fabric but this one with it’s eye-catching colours just had my name on it!
Once I had it in my hot little hands I had to come up with a design for a jacket. My starting point was a vintage pattern for a kagoule-type top which is probably from the late 50s-early 60s but there’s no date on it sadly. As was typical of patterns from that period it’s a single size, medium, which I already knew was OK because I’d used it once before about 4-5 years back. I also have a cheap-as-chips packamac which is a nice style but turned out to leak like a sieve! I would use this as my sample to follow how components like the zip and a storm flap on the front go together for example. There were a few other patterns which gave me some ideas including The Maker’s Atelier Utility Coat and from these various sources I sketched a few drawings to come up with a design I liked.
As the fabric was expensive I only bought two metres so I had to progress carefully for each step. I made a new pattern for most pieces because the new version would be mid-thigh length and have a full length front zip opening to be covered by a storm flap, plus I repositioned the shoulder seam forwards to minimise possible leakage through the seams. I altered the side seam shaping a little by curving them out slightly, to give a bit more room for bulky jumpers/sweatshirts. I reused the original hood and sleeve patterns, plus I settled on two pleated patch pockets with separate flaps on top. To reinforce the shoulder area I made an inner lining pattern which acts as an internal yoke.
I read up a few general tips for sewing shower proof fabric before I started-I didn’t need it to be waterproof so I didn’t tape each seam but I did lengthen the stitch slightly, to reduce the number of puncture holes through the fabric which could potentially let water in. I also used a fine Microtex needle to reduce any friction there might be whilst sewing too. This fabric is different to other woven fabrics because of it’s special coating so any mistakes which have to be unpicked would leave holes. It’s possible to press it carefully but not too hot or you could melt it. Use a pressing cloth over the top and warm the iron up incrementally on a scrap piece until you’re happy with the temperature.
It took me a little while to source the hardwear I needed, many suppliers of zips had the length but not the colour, or the colour and not the length! Eventually I bought two open-ended zips of different colours from Jaycott’s. I couldn’t seem to find any suitable coloured round elastic online so eventually I settled on narrow grosgrain ribbon from VV Rouleaux for the hood and back waist detail instead, plus I sourced some small spring cord-lock toggles to secure the ends where needed. I found the lining for the hood and the shoulder yoke amongst fabrics I already had.
I sewed the jacket up in ‘bite-size’ chunks of time rather than pushing on through-mostly because I was often waiting for something to arrive in the post before I could do the next part. As I wasn’t following a particular set of making instructions I was winging it to a large extent, the order of making was often influenced by another section of the garment having to take a priority at certain points.
It would have been better if the sleeves could have been just 4-5cms longer-I’m not sure why they seem short because I’m sure they weren’t on the original sweatshirt-perhaps the big difference in fabric types was a factor? Anyway, no matter, I added a small section of elastication to the top of the cuff to bring it in slightly to help prevent drips seeping back up my arms if possible! I should add that normally I would pattern-match the print but I didn’t see any need to do that for this jacket.
Because this is very much a ‘make it up as I go along’ garment I used some of the ribbon to neaten the neck/hood seam and jolly nice it looks actually!
For an unplanned garment I’m very pleased with the outcome, I love the colours and I hope it will be useful, it folds up pretty small so I can shove it in a bag if I’m going out and don’t want, or need, to take a heavier coat. It’s very much one of a kind! In normal times I wouldn’t have been sourcing everything online, I enjoy browsing in real shops for haberdashery and trims, but not just at the moment.
This whole project all came about because I couldn’t resist some ex-Prada fabric I spotted on my friend Dibs’s website, Selvedge and Bolts! She specialises in sourcing gorgeous quality high-end and ex-designer fabrics from Italy and France. This one caught my eye because funnily enough it doesn’t scream ‘designer’ but I liked the graphic print which stands out amongst so many florals.
I ordered 2 metres although I didn’t have a plan for it, then it occurred to me that I should look at actual Prada designs to see if there were any that were at all wearable by someone like me (ie. not six feet tall or looking about 17 years of age!) Somewhat surprisingly there were some really lovely shirt-dresses in eye-catching fabrics.
This was just the springboard I needed so, after a bit of a search through my patterns, I found this McCalls 7470 which had originally been free with Love Sewing magazine at some point in the recent past. The Princess seam lines and shirt styling were exactly what I wanted except I would change the skirt to be a dropped waist dirndl to echo the original.
The #7470 is a Palmer Pletsch fitting method pattern which I’ve never attempted before. I’ve been thinking lately that many of the garments I’ve made in recents months have either been old favourites or very simple shapes with little use of interesting techniques or style lines. I needed to stretch my sewing muscles a bit more-use them or lose them-so I set about following the instructions to tissue fit the bodice first. By a combination of body measurements, knowing my body quirks, periodically trying on the pinned tissue and using my padded-out dress stand Doris I arrived at a fit that I was happy with.
I’m not going to claim it was particularly easy but there are a lot of written instructions on how to approach it on the accompanying sheets to help you, plus online tutorials too. I’d recommend making a toile (or even two) if you need to before using your fashion fabric to avoid expensive mistakes.
I knew fairly early on that my 2 metres of fabric wouldn’t be enough for what I had in mind, and I didn’t want to waste my lovely Prada fabric so I opted to make the pattern instead in a vibrant printed stretch cotton which I’d bought in Paris at last year’s Sewcial event.
I took my time sewing the dress, I wanted to enjoy each part of the process. There is a two-part collar for example, pleated patch pockets with flaps, and a band running right down the front. I had a few problems with insetting the sleeves though. I’d made a small alteration the back of the arm scye which resulted in it getting a little smaller so I expected there to be a discrepancy but it was much bigger than I anticipated, the sleeve head was far too large and wouldn’t fit without puckering and gathering. I looked at a few examples of #7470 on Instagram and many versions were either sleeveless or didn’t mention it as a problem. Anyway, after a lot of fiddling about in the end I dropped the arm scye down to make it larger so that the sleeve head fitted properly.
The skirt was simply 3 rectangles, two for the front and one for the back which I pleated onto the shirt top using a fork to make each pleat even.
So what started as a Prada-inspired dress for one fabric has still ended up as a Prada-inspired dress but made in a different fabric! I finished the whole thing off with these beautiful buttons from Textile Garden all the way down the front.
So that’s my Prada-inspired dress up to this point, just not made with actual Prada fabric. I have a plan for it though because there was another shirt-dress that caught my eye…
I’m really pleased with the outcome and the way it fits, and because I took my time and didn’t rush, it was an enjoyable process. I’d fallen into the habit of making simple projects, I felt something more complex was needed.
Two years ago one of my early makes as a Simple Sew blogger was the Kaftan pattern made in a tropical print cotton lawn kindly given by Doughty’s online fabric store. It was very much a ‘holiday’ garment but, even so, I didn’t wear it as much as I’d hoped because whilst the fabric was quite lightweight there was too much of it around my legs, it was probably a size too large and the whole thing just looked quite bulky. It would have been better in something like a very lightweight cotton voile or Batiste, or a printed chiffon or georgette as a swimsuit cover-up.
Anyway, rather than make another new garment for my next Simple Sew post I’ve decided to refashion the Kaftan into pyjamas instead, retaining the top section and cutting shorts from the remainder using the Lapwing trouser pattern.
I studied myself in the mirror wearing the Kaftan and decided to reduce it to approximately 25cms long from the original waist seam at the side-I would make it level all the way around although the waist seam rises up at the centre front. With the remaining fabric of the skirt I would make the shorts
I took the cord out of the waist and initially decided I would replace it with elastic instead although eventually I changed that plan. I felt the sleeves were a bit long and restrictive to sleep in so I shortened those too by about 5-6cms. I removed the pompom trim first although I didn’t reuse that in the end because I opted to create a curved opening on the shoulder seam instead, to soften the lines.
I partly unpicked the shoulder seam and overlocking sufficiently far that I could re-overlock the edges singly and then roll hem finish them so that the overlock stitches were enclosed.
I also took quite a bit of fullness out of the bust section at the underarm so that it would fit closer to my ribcage, I didn’t remove any corresponding fullness from the newly-shortened skirt though, I simply pleated it up to fit the top part and rejoined them together at the waist seam.
I neatened the new hem using the overlocked rolled hem method again and finally trimmed the waist seam with co-ordinating pink rick-rack from Backstitch. I decided against putting elastic in the original casing because I felt it would ride up while I slept and become annoying around my ribcage. This has proven to be the right choice because the top is comfortably loose without being huge.
Moving on to the shorts, I used a RTW pair I’ve had for years to compare measurements and also to compare against the size chart for the Lapwing trousers. I traced off the pattern in a size 14 because I wanted to create a hem similarly-shaped to my RTW ones for the shorts, they have a slight upward curve at the side seams (I dithered about adding side pockets as per the pattern but in the end I left them out, I thought about adding a patch pocket on the back instead but I didn’t do that either!)
I was able to fold the original front skirt section down the centre front line and cut a pair of front shorts pieces from that. I placed the piece as near to the top as possible so that I had the maximum amount of fabric left to cut the bias strips from.
As is very often the case the back section of trousers was bigger than the front so this meant I couldn’t cut it out of folded fabric. I laid the fabric out flat instead and cut them singly using the centre fold as my guide for the grain and making sure to flip one so that I had a pair, not two the same!
In order to hem the curve I made a wide bias band pattern piece which, ideally, I would have cut one for each leg but the remaining pieces of fabric from the front skirt didn’t allow me to do that so I cut several shorter pieces which I joined to make a long enough strip.
I joined each side seam first, neatened it and pressed towards the back. Having joined the bias strips I pressed over one long edge by 1cm. In order the self-neaten the hem I placed each strip RIGHT side to the WRONG side of the shorts (see photo) and stitched it in position.
Then the strip flips up to the right side, thus also being right side out and enclosing the raw edges. You could simply top stitch this in place along the folded pressed edge or add a trim, I put more rick rack on here to match the top. Now sew up and neaten the inseams.
The rest of the shorts were very straightforward, I placed one leg inside the other so that the crotch seam was right sides together then stitched it twice a couple of millimetres apart before neatening.
I pressed over the top edge by 3.5cms then made two round-ended buttonholes for the ribbon to come through at the centre front. Next I top stitched close to the top fold, then sewed another row of stitching 3cms from the fold to create the elastic channel. I measured my elastic for a comfortable fit and added a short piece of dusky pink ribbon (which probably came off a gift bag or something) to each end of the elastic. I slotted this through the buttonholes and then secured it so that the elastic was just out of sight with only the ribbon showing through the button holes. Job done!
I’m pretty pleased with how my new pyjamas have turned out, I reckon I’ve already worn them more times than as a kaftan so that’s got to be a good thing, right? At least this pretty fabric isn’t languishing in the wardrobe waiting for a warm sunny holiday which is nowhere on the horizon any time soon!
I’m a bit uncomfortable about sharing photos in my PJ’s but it’s in a good cause I guess.
Over on the @SewOver50 account recently I shared a few of my favourite ways to finish hems or raw edges, although course it is absolutely NOT a definitive list by any means. I thought I would expand a little here on the blog using more photos of projects I’ve made in recent years. They are in no particular order either and if I wrote a blog post about the whole garment then I’ve linked it so you can read more if you want to.
Obviously there are the usual hand-finished hems using slip hemming stitch or herringbone stitch for example, which I use a lot too, but I thought I’d share a few alternatives which you might not know, or haven’t used for a while.
I’m beginning here with a faced hem…
The next one is an interesting hem finish which is very useful especially if you want a quality finish on evening or bridal wear. It uses something called ‘crin’, crinoline or horsehair braid (it doesn’t involve actual horsehair any longer though!) I’ve used it here on an organza skirt for the Dior New Look-inspired evening dress I made 4 years ago. As well as a crisp finish I wanted the hem to have distinct body and wave to it so this was the ideal technique. Crin comes in various widths, this was 5cms, lots of colours too because it’s more commonly used these days to trim hats and fascinators.
If you’re making a wedding dress for example and mounting all the skirt pieces onto another fabric, when you use crin on the hem (or bias binding for that matter) by hand-sewing the hem all your stitches will be invisible because you can catch them just through the mounting fabric. This is a couture technique so if you look at red carpet dresses with no visible stitching at the hem this will be how they achieved it. You can apply it as appropriate to any garment that you’ve mounted to another fabric though.
The next couple of photos are where I’ve used bias binding to neaten a hem. I find this a really useful technique if you need the maximum amount of hem because you can sew a very small seam allowance. It’s good if you’re letting down hems to gain length too, on trousers or children’s clothing for example.
If you have fine fabric why not consider using your overlocker if you have one on the rolled hem setting? Refer to your manual for specific instructions how to adjust your machine and make samples first to ensure it’s going to be satisfactory for your particular fabric. You’ll frequently see it used on chiffon or georgette but I’ve used it successfully here on fine cotton lawn, jersey and a stretch velour. If you don’t have an overlocker you can probably achieve a similar finish on your sewing using a rolled hem foot ideally and a small zigzag stitch-as always I would urge you to experiment to see what is possible. Some of the simplest machines can still give you an interesting variety of finishes.
I find the next couture/tailoring technique very useful on sleeves as well as coat, jacket or dress hems. I’ve used it here on my Tilly and the Buttons tester-made Eden. I wasn’t taught this method as such, I discovered it for myself whilst doing alterations taking up sleeves for people. I haven’t ever encountered it in pattern making instructions but I think it’s an excellent way of stabilising the cuffs of coats and jackets.
For this next finish I’ve used a triple straight stitch to create the effect of top stitching on the hem, and several seams, of this Simple Sew Zoe hack I made last summer.
If you have the foot attachment and stitch capability for your sewing machine you can always try blind-hemming. I must admit I don’t use it that often, and only then on completely straight hems. There is a bit of a knack to it and I tend to only use it on a busy print which will disguise any botched bits (yes really!) or if I’m tight for time compared with any other method. It’s not quite the same quality of finish you will see on RTW clothes though which uses a specific machine to blind stitch the hem.
I think it’s worth mentioning that I like to use bias binding to neaten necklines (and armholes) too. I particularly like this as a way of avoiding using a neck or armhole facing which can be notorious for constantly rolling into view or flapping about annoyingly. The version you can see in the following two applications is a strip which I’ve folded in half lengthways first, the raw edges are matched and sewn. The seam is trimmed slightly and snipped if necessary, then turned so that the edge is enclosed and finally topstitched close to the folded edge to secure. In both the following examples I have sewn the binding on the wrong side of the fabric so that the binding turns to the outside to be visible and decorative but you could just as easily sew it to the right side so that it turns to the inside of the finished garment.
I’ve have included another variation of binding on a hem to show you how it can be combined with other techniques to achieve a quality finish. I used it here on a sheer organza which was mounted onto a backing fabric of slipper satin. This meant that when I turned the hem up the hand-stitching was invisible from the outside because the stitches only went through the mounting fabric.
The next technique is more usually the choice of the pattern designer than the dressmaker, although if you know a little about pattern cutting you might be able to do it for yourself. This is an example of a deep grown-on faced hem on the Trend Patterns Square dress which I’ve made twice. It works brilliantly on this dress because the hem edges are straight (square!) plus it gives real weight to the hem which is another satisfying detail.
Pin hemming is a technique I’ve used for decades on fine fabrics. You can replicate it using a rolled hem foot attachment on your machine although it can be trial and error which size works best for you with variable results. I have two different sizes of foot, 2mm and 4mm and I can’t get on with either, I’ve since been told that 3mm is the optimum size for most fabrics but I’m not prepared to risk another mistake when I know I can achieve a good quality result this way instead.
Simply put, I turn over the raw edge by approximately 5mm and stitch very close to the folded edge. Carefully trim the excess close to the stitching line and give it a light press. Then turn again and stitch a second time on top of the first row of stitching. This particular example is from the Trend Bias T-shirt dress I made a few months ago.
If you read about my pattern hack of the Simple Sew Cocoon dress you will see how this variation of hemming came about. I added a large chunk of fabric to give extra length to a dress that would have been too short without it. This method is probably best on a straight hem, you could use it on sleeves too.
This next one is a very much trial and error. I used an edging stitch on my Pfaff sewing machine to hem this Broderie Anglaise blouse which I made recently.
I’ve used a variation of a faced hem recently when, instead of bias binding, I used straight strips of fabric to turn up a straight hem on a dirndl skirt. There will be a blog of this particular garment coming soon…
To finish with is a very simple method of rolling a fairly narrow hem. Overlock the edge first using three (or even two) threads then carefully turn it once and then again so that the overlocking is enclosed inside. If the fabric is quite ‘bouncy’ and won’t stay in position you could press the edge over once first and then roll it the second time. Whilst the result is wider than pin hemming it is narrower, and possibly quicker and more accurate, than a simple turned hem.
This last suggestion is from a project which will be blogged very soon. I cut 6cms wide bias strips which I used to create a self-neatening hem on a pair of pyjama shorts.
I hope you’ve found my suggestions useful or thought provoking, is there something here which you’ve never encountered before, or that’s made you think how you could use a technique you already know in a different way? The idea is to show you a few ways of finishing hems, or raw edges, in new and interesting ways. I’ve not included the usual hand stitching methods because there’s nothing new to think about, although please let me know if you use these methods in a more unusual application. Just because the pattern instructions tell you to finish the hem a certain way doesn’t necessarily mean you have to do it that way…although think it through carefully just in case the really is a reason!
In 2016 I took part in Portia Lawrie’s Refashioners competition for the first time when I made a jacket from two pairs of Mr Y’s old jeans, you can read about that one here. I was jolly pleased with it and wear it a lot and obviously I didn’t win although I did get a mention in despatches so I was chuffed with that.
For Refashioners 2017 Portia announced it would be SUITS! Eek, I thought, I’m not sure about that…anyway, nothing daunted, I started thinking about what I might be able to do if I tracked down the right suit. I knew I didn’t want anything too dark or work-a-day so I hoped to find something in a check perhaps. Funnily enough it didn’t really occur to me that it could be something like linen or suede, or a woman’s suit so when the inspirational Blog Tour throughout September started and it featured some of alternative fabrics I did think “oh, why didn’t I do that?” Hey ho…
When it came to inspiration however there was only one person whose tailoring I was interested in and that was Alexander McQueen. The retrospective of his work ‘Savage Beauty’ at London’s V&A museum in 2015 was absolutely mind-blowing-I went 8 times! [I bought annual membership to the museum so that I could go as often as I wanted, it’s fair to say I got full value for my money. I’ve kept up that membership ever since and use it regularly] Whilst I’ve no hope of ever acquiring or wearing McQueen (apart from my treasured silk scarf which Mr Y bought for me at the end of the exhibition) I greatly admire his meticulous tailoring, originality, attention to detail and craftsmanship which has been ably continued since his death by Sarah Burton. [I didn’t blog about Savage Beauty at the time but I wrote one about a fascinating parallel exhibition that was at Tate Britain, you can read thathere]
Portia had set up a Pinterest page of inspiration too so I had a look there as well as internet searches of my own and the book which accompanied the exhibition and is full of wonderful images. So many clever ideas but there would be serious fabric constraints as I only wanted to use one suit, once I’d tracked it down, which meant some things like dresses with elaborate details would be impossible. If I was going to invest quite a lot of time into this it needed to fit me and I’m not a stick insect so I have to be realistic!
I collected ideas and images although some of them were unlikely contenders, for reasons of practicality, quantity of fabric and my own skill level. [I went on a tailoring course at Morley college in London last year and picked up loads of useful skills and the confidence to tackle this head-on, have a look at their prospectus because they offer some great courses] I liked the idea of combining different fabrics and techniques, particularly over or near the shoulders.
I scoured all our local charity shops but didn’t find anything I liked, Mr Y and my Dad didn’t have anything in their wardrobes either. Then, when we were visiting Salisbury in Wiltshire at the end of August, we tried a couple of shops when I spied a black and white checked jacket. It seemed to have trousers with it which didn’t match but these were Prince of Wales check! Looking further along the rail we discovered the right jacket for the trousers was on another hanger-yippee, success! a matching suit in the perfect fabric. It was £25 which was a bit more than I had hoped to pay but the money would go to a good cause so it was a win/win situation really. Even better was the fact it was 100% pure wool and it was a Daks suit from Simpsons of Piccadilly which would have been pretty expensive originally-I definitely lucked out with this one. At £25 though it did mean I would only use one suit rather than buy possibly 2 to mix together. No matter.
So now that I had the suit I needed to come up with a design. I also set myself the rule that I wouldn’t buy anything else so everything had to come from supplies I already had in my workroom. I tried to be a bit ambitious-and different from last year-and initially came up with a few dress designs where I thought I might be able to utilise the trouser legs to make panels and a feature-zip detail.
Before I went too much further though I needed to disassemble the suit to see exactly how much fabric I had. I got out the snips and unpicker and set to (not without trepidation because it was a lovely suit)
The beauty of pure wool is that it presses like a dream and so almost every original crease in the suit disappeared once I’d broken it down into all the parts. Needless to say there was less fabric than I’d hoped for my big plans so I had to modify them a lot. Out went the dress and in came [another] jacket. I’d been looking through my not inconsiderable pattern stash for inspiration and I’d found a dress pattern from 1973 which was amongst a huge number gifted to me last year by a friend. They had belonged to her Mum who was a fabulous dressmaker at Cresta Silks in her youth. Even though it was a dress I was attracted to its striking style lines with a long bust dart that ran parallel to a diagonal under-bust seam, and because it had a centre front seam I thought it was easily adaptable to a jacket. One of the features of McQueen’s work is his unusual seaming and style-lines so I decided to make a toile and see how it went.
The original collar opened at the back for the zip so I made a new pattern so that it opened at the front instead. I also had to change the front and back ‘skirts’ by dividing them evenly in half because the pieces would be too large for the fabric quantity I had. I also wanted to be able to cut various pieces on the bias to make it more interesting so they had to be smaller to achieve this.
By using an open-ended zip I minimised the amount of fabric needed for the front opening, there was no need for an overlap and there’d be barely enough anyway. I also knew that if I could use the original sleeves I would be be able to use all other available fabric for my design.
Amazingly I was happy with the toile and decided to press ahead with the design as it was. I could get the new front panels out of the original, and even managed to include the breast pocket and all the under-linings. However I couldn’t work out a way of satisfactorily utilising the pockets and flaps so they got left out. In the end I couldn’t use the back as per the toile, which had darts and the pattern piece was too large to fit as it was, so I turned the darts into princess seams instead and then those pieces came out of the original back after all. There was a tiny hole in the back but I repaired it with iron-on interfacing and no one would be any the wiser. I’d wanted all the peplum pieces to be on the bias but in order for them to be a reasonable match some had to be on the straight instead.
I won’t pretend that every seam has perfectly matching checks but given the fabric constraints I’m really pleased with the outcome. I carefully made the jacket up, a very enjoyable process, and because it was being fully lined I didn’t need to neaten any of the seams inside, they could just be pressed open. I remembered my tutor Daniel at Morley saying “steam is your friend” and wasn’t afraid to use it often, in conjunction with my tailor’s ham and a pressing cloth.
The trickiest part of the construction was making the original sleeves a little shorter for my arms and to fit into the new armholes. I roughly measured the sleeve head and compared it to the armhole. There was a fair difference so I needed to reduce the sleeve width by sewing up some of the under-arm seams to about elbow level (they are two-part sleeves) I tacked one sleeve in and tried it out. It looked pretty satisfactory without any further adjustment so I did the same to the other one as well. I tried to ensure that the checks matched as best I could too. Again I tried the jacket on to make sure I could move my arms and that I was happy with their length. After I’d machined them both in I reused the pieces of canvas and domette which I’d taken out of the original sleeve heads. These are part of tailoring construction which help give a good rounded shape to the sleeve head and are basted in place by hand onto the jacket seam allowance itself. I also planned to reuse the original shoulder pads later on.
Once the sleeves were in I could think more about the decoration I wanted to add. One of the recurring features I like about McQueen’s tailoring is his use of lace appliqué and embroidery. Amongst my stash of fabrics I have some beautiful black Guipure lace which was left over originally from the bridal shop where I used to work creating and making the most beautiful wedding and evening gowns. I’d used some of it on my elder daughter’s Prom dress 10 years ago but there’s still some left over so I had a little play. I put the jacket on Doris and draped pieces of lace over the shoulders to see what looked best. Part of the beauty of Guipure is that you can trim it into shape without it fraying or falling to bits so once I’d positioned it where I wanted I could trim it to neaten the shape. I love the swirls!
Looking at these photos you can see the other decorative technique I decided to use, embroidery.
I’d seen a very recent McQueen design which had red lacing on and I wanted to incorporate something similar probably in the form of hand embroidery instead, particularly because the fabric has a fine red stripe running through it.
I had a few practices first at simple running stitch, sashiko-style, and I tried a sort-of feather stitch but it looked pretty rubbish and uneven as I couldn’t get it right or consistent so I tried a couple of stitches of the many that my 25-year-old Elna 7000 machine offers.
I liked the feather stitch but decided it would be over-doing it so in the end I settled on the saddle stitch which would normally be used to top stitch but I was going to run it along some of the red stripes in the fabric for emphasis. [If you’re not sure which stitch this is on your machine it’s the one where the picture looks like 3 rows of stitches side by side. It’s actually 3 stitches on top of one another when it sews thus making an effective top stitch]
I decided to follow a few of the red stripes on the front and back, the front ones all run vertically and the back ones are just on one side in a cross formation. I considered putting them elsewhere too but decided there was enough.
Once I’d finished all the decoration I put the shoulder pads and the ‘plastron’ back in (this is a piece of heavy canvas which is part of the underlinings of tailored jackets and which helps give it a smooth line over the chest) The plastron needed to be trimmed slightly to fit inside since it had come from a man’s jacket. Finally I’d managed to salvage just enough fabric in one long strip to make a very narrow facing inside the zip. I turned up the hem first basting it in position and then herringbone stitching it by hand.
I’d found some black lining fabric in my stash so cut out the jacket lining (excluding sleeves because they had their own original lining in) and sewed it together. Red lining would have been nice but I didn’t have anything suitable and I’d have broken my own rules to buy some. Because the facing strip was so narrow I wanted to smarten up it up a bit so I dug out some black braid which I stitched down the edge of it-it looks much better now if the jacket is open.
Next I hand stitched all the linings in position at the hem and around the armholes so that everything was enclosed. The final thing I decided to do was change a couple of the cuff buttons so I swapped one on each wrist to red ones.
And that’s all there is to it…..
I’m afraid I’ll never make much of a model and the backdrop was a choice of either a brick wall or a flower bed! The photos aren’t by Testino (Katie actually) but I hope you’ll get an idea of how the jacket looks, it’s a distinctive but wearable one-off.
I’m so chuffed with my finished jacket and, better than that, I really enjoyed the planning and making very much. I felt I got back in touch with lots of the skills I’ve acquired over many years of sewing, some of which helped me to plan it carefully within the constraints set both by Portia and the ones I set myself, and others meant I could stretch my making skills further than they tend to get stretched these days which is no bad thing.
Initially I wasn’t sure if this would be a refashioning challenge I could rise to but I’ve surprised myself with the outcome. I’ve now got a jacket which I’ll be really happy to wear and I shall enjoy telling anyone who cares to listen exactly how it came about. I don’t know the story of the suit before I bought it but I feel like I’ve given it a new narrative now by reinventing it in a new form….and that might even be something McQueen himself would have applauded.
As ever many pictures are my own but the rest are sourced from the internet.
Have you made a suit refashion this year? I’d love to hear about it, or tell me your thoughts about mine…(risky hehe)
There’s a lot going on in this post because I’m offering you my thoughts on not one product but three!
So, a bit of background first…I used to be a keen runner but various injuries forced me to stop and then I never quite got started again. Fast forward at least 3 years and I’d gained weight which I wasn’t happy about, I felt sluggish and lacking in energy, I wanted to lose the weight for the good of my health and mental wellbeing. So, coming up to date, the return to running is going well (if cautiously…) and I’m losing some weight which in turn has inspired me to try making some of my own activewear. Fortunately for me Melissa Fehr of Fehrtrade has become a sewing friend of mine since first meeting her at the Sewing Weekender a few years ago and she generously offered me a copy of her Tesselate Tee pattern to try. I’d helped test her Rouleur leggings last year so I already had that pattern. Part of the beauty of Melissa’s patterns is that she gives you really comprehensive instructions to be able to sew activewear using just a regular sewing machine if you don’t own an overlocker. I’m in the fortunate position at the moment to be a Pfaff Brand Ambassador and I have their air-threading Admire Air 5000 on loan, along with a Coverlock 3.0 as well so this all seemed like the perfect opportunity to make some new running kit.
Suitable activewear fabric is not something I have in my stash other than the scraps left from testing the Rouleur leggings so I had a little online search and came across Frumble fabrics. They have a good range of activewear fabrics at competitive prices as well as an impressive selection of suitable elastics and other trims or haberdashery you might need for this sort of project. I bought a metre of plain navy fabric and a metre of navy camouflage print, along with navy soft waistband elastic, some navy fold-over elastic and, finally, silicone grip elastic. [One point I should add here is that I decided not to pre-wash the fabric, this was based on my own knowledge and belief that synthetic fabrics are usually more colour-fast than natural fibres. I was wrong. The navy came off on my hands as I was making it up so as soon as I finished both garments they have been through the wash after all. I have alerted Frumble so I’m not saying anything here that I haven’t already fed back to them. Overall I’m pleased with the fabric quality and I learned my lesson-prewash even if you think it doesn’t need it!]
I opted to go for a medium size Tesselate top, Melissa has recently layered the pattern so now you only need to print off the size or sizes that you want, I wavered between small and medium according to my measurements. The small probably would have been fine but the medium gives me a little more room without the constant thought that I should be sucking in my wobbly bits! One of Melissa’s USP’s with her patterns is interesting seam lines which means, as well as striking designs, you can often use up small pieces or remnants of suitable fabrics. The Tesselate has a variety of options including short or long sleeves, thumb cuffs, a hood (with ponytail hole!) and back zipped pocket.
I cut the leggings a mixture between small and medium and I’m happy with the fit of the end result. I had enough fabric for long sleeves on my Tesselate and, although there’s a pattern for the back pocket, rather than print it off I made my own.
I played around with the fabrics until I was happy with their placement, I had enough of the blue spotty fabric for the back and front side panels, everything else I divided between the two navy fabrics.
I’ve made another little video to demonstrate how the air threading works on the Pfaff, you’ll need to bear in mind that it might seem like it takes a while to thread and so where is the advantage in air threading but that’s because I’m trying to explain as I go and I was sitting at a funny angle behind the camera whilst I did it.
After two years of owning the Quilt Ambition 2.0 (now discontinued) I’m used to the quality of Pfaff machines so it doesn’t surprise me that the Air Admire is sturdy (no shifting about on the table while you sew) and very speedy, with a superb quality of stitch. It doesn’t take long to get to grips with the air threading and, as I mention in the video, there’s an automatic threader for both needles too! I couldn’t get the hang of that at all to start with but it’s amazing what a difference it makes if you read the instructions and follow them! Of course, this is an expensive machine and I understand that not everyone will have that kind of budget but if you are considering an air threading overlocker (there are now a lot more models on the market than just market-leader Babylock with prices gradually coming down) then this one is most definitely worth thinking about.
I inserted the invisible zip on the sewing machine, then attached the pocket bag that way too. The T-shirt goes together pretty quickly considering the number of pieces-most pieces are cut singly because they are asymmetric-if you’re using the same fabric throughout it would be an idea to label your pieces in some way so you don’t get them mixed up.
I find it very useful having a variety of stitches to choose from especially when sewing with stretch fabrics, the 3-step zig zag was ideal when I was sewing the elastic into the waistband, I also have an ‘elastic’ stitch which is useful. A lot of machines, even quite simple ones, will probably have a stitch option which will enable you to sew activewear so why not try out a few of them to see exactly what they are, the instruction book should be helpful, or there’s so much information on the internet too.
To neaten the hems and around the neck I swapped over to the Coverlock 3.0 which I had on the coverstitch setting. Again, this is a very sturdy piece of kit with excellent stitch quality, I am finding there is a certain knack to using it and I’m by no means an expert yet but it certainly gives a very professional finish to knit, jersey or stretch garments.
As always, I hope you’ve found this helpful, I always try to be honest about how I get on with a product whether or not I’ve been gifted, loaned or purchased it-all three in this case. If you’re tempted to have a go at activewear then Melissa is a good place to start-she’s even written a book on the subject so you’re in good hands!
This is an edited version of the original post from 4 years ago. Not all the pictures are here but I hope you get the gist of the jacket refashion. Sue
I’ve never been a great one for up-cycling really, I guess as a former sample cutter I always enjoy the challenge of cutting something new out of fresh fabric in an economic or inventive way. I think that’s probably the same reason I’ve never bothered with quilting or patchwork-cutting fabric into small pieces and then reassembling it in a different order-not for me I fear. Mind you, back in the day we were less concerned about ‘reduce reuse recycle’ than we’ve since, thankfully, become.
Anyway, at the beginning of August, Portia Lawrie announced that her Refashioners 2016 competition for this year would be to turn jeans into…something else, anything you like! Last year’s theme was shirts and I saw plenty of imaginative ideas where mens shirts became dresses, skirts, different shirts and the winning entry was trousers!
Anyway, I was pondering vaguely on the theme (almost entirely driven by the amazing prize-package that was on offer, the prospect of fabric/patterns/sewing books is enough to stir me into action) and thinking that I didn’t actually have any old jeans in the house to cut up-my girls wear way too many stretchy skinny jeggings to be useful and Mr Y is a keen believer in wearing things to infinity and beyond!
However, as luck would have it, Mr Y was having a rare ‘turn out’ and what should I find but TWO pairs of almost identical jeans…except they weren’t denim jeans, they were corded drill (looks like corduroy but not fluffy) Would they do? a quick email to Portia who said she thought they would. Excellent-green for go!
The next issue was that they weren’t even blue, they were very similar, very well washed shades of stone/sand/beige…you get the picture? Then I remembered I had a packet of unused Dylon machine dye in indigo-score!
So I set about unpicking the offending trousers…this took rather a long time to be truthful and made a huge mess with all the threads everywhere on the carpet in my workroom, Threadquarters.
I didn’t have a clear idea of what I wanted to make but I knew that the more useable fabric I could harvest the better. Once I’d taken everything apart I had four legs with side seams still intact, two waistbands with pockets attached and two zips removed. I popped the whole lot in the washing machine with the dye and 500grams of salt, you run the hottest cycle and then, when it’s complete, you run the whole cycle again with detergent. This is to remove any excess dye and also wash the machine out too (although the next proper wash I did was a dark one just to be on the safe side) I was pretty pleased with the outcome. The two pairs were by and large virtually the same colour now, interestingly the top stitching on both hadn’t dyed as the thread must have been synthetic, and the zips hadn’t either. That was a pity because I thought I might have been able to use them but they were just different shades of brown now-yuck.
After a lot more thinking, and sketching, I settled on a jacket for myself because I took the view that if I was going to spend such a lot of time on this with not a lot of realistic hope of winning I wanted to at least have something I’m happy to wear!
To work! I had a rummage in my-ahem-extensive collection of patterns to see what I had that might be basis to use. Most jackets I’ve made were years ago so they’re all a bit 80’s tailored but then I came upon a pattern from the 1970’s that my neighbour had given me when she was having a turn out (more recycling?) The jacket in itself wasn’t something I’d wear but I loved the curved bust dart in the front, it was collarless and edge to edge and the back was in two pieces.
All this meant that it could be a go-er. I spent a while fiddling with the pattern pieces and the trouser legs to see what was going to go where. Because I wanted a shorter length jacket that helped, the front would fit on to include the original side seams and the back would go above that with a modification, and the sleeves would come out of the other legs. They were all mostly on grain which pleased me a lot. (When things aren’t cut on the grain or on the bias they can go very wobbly when sewn up)
I forgot to mention that I decided to trace off a new spot and cross copy of the original as it was quite tatty, and I was shortening it anyway.
Because the back wouldn’t fit on without overlapping the front I chose to add a panel in the back so that it became four panels. This isn’t difficult, I just drew on the new seam line where I wanted it, added seam allowance of 1.5cms and a balance mark to the back panel section and cut it off. The remaining new side panel then needs the 1.5 cms added back on plus another 1.5cms for its own seam allowance. The photo should clarify this a little.
Once I’d got the panels sorted I could pin them onto the fabric.
I tried as much as possible to keep things on a proper grain line so that they behaved when I started sewing them together. Out of the other legs I cut the sleeves which I positioned so that the original seams ran straight down them. One of the things I liked about the pattern was the little elbow darts which would give them a cheeky feature.
Another rummage in my stash found me an open-ended zip in blue, I’d decided to tidy up the inside-and make it a bit more individual-with pretty bias binding. I managed to cut front and back neck facings out of what I’d got left from the sleeve leg.
Sewing the jacket together was very straightforward after that. I top stitched most of the main seams in part to match them to the originals and to link it all together, this meant I had to put the sleeves in on the flat rather than set-in but they look ok.
Because the zip was too long it gives an interesting finish to the neckline where there’s a section at the top that doesn’t do up, which I like. I wanted to use the pockets too but I didn’t want them spoiling the outside clean lines so I devised a way of having them on the inside.
The lower facings (cut from more scraps) fold up to neaten the bottom edge of the jacket.
I ran out of the red binding but I found about a metre left of the binding I made to go on my favourite dress so I used that instead. I understitched the lower edge in a fluoro-pink thread (just because) and then slip stitched the facing in place by hand so that it didn’t show through on the front. [I put binding on the cuff edges too so if I turn them up it’ll be visible]
I think the internal pockets might be quite useful if I ever go poaching!!
The only bits I didn’t find a use for in the end were the waistbands. I thought I might have used them on the lower edge but in the end I decided I didn’t really want the band on it and I wasn’t sure poor my machine could cope with the number of layers that it would have to sew through.
So there you have it, my entry to The Refashioners 2016. I’m really pleased with the outcome, it’s a tad big but that’s fine and it’s totally wearable. I used jeans that were headed to the charity shop (or even the bin), a gifted vintage pattern, binding I already had and a zip from my stash, a win all round I think. Needless to say I didn’t win the big prize but I did get an honourable mention in dispatches.
The jacket got its first outing in the wild, on the way to the first Sewing Weekender in late August 2016. I’m very happy with it and I’ve had loads of wear out of it. I think it achieved my aim of not looking too much like a thing that’s been made from something else and being not very good in the process. I’ve never really aspired to being designer so I know there will be far more original ideas than this but I want a garment that is wearable and useful to me and no one else. I hope you agree…although you probably wouldn’t say if you don’t!
If you’re reading this in 2020 (and what a very strange year this has been!) you might have seen me wearing the jacket for my first trip back to the V&A museum in almost 6 months, the wearing of face masks being compulsory. I’m wearing it with a linen Trend Patterns Bias T-shirt dress which I included in a review here. The exhibition is Kimono: Kyoto to Catwalk which I also reviewed earlier in year. My hair has grown quite a bit too!
Again, apologies for the gaps in the original photos but I hope you get the general idea of this refashion.
There are a quite number of blogs and websites out there that can give you ideas and inspiration for this kind of project and Portia’s own is as good a starting place as any, she’s a great advocate of refashioning with so many clever ideas and in 2020 this is still very much the case.
I followed the progress of this pattern with interest on Instagram when it was originally released nearly two years, it was fascinating to see how Claire-Louise Hardie (the Thrifty Stitcher!) developed and finessed the various elements of it as she sampled it, up to the point that she was ready to release it for sale. It has attractive style lines with princess seams in the front which curve into hip pockets, the back also has princess seams and there’s a horizontal seam just below the natural waist. The collar curves up smoothly against the neck and the back collar has a ‘sunray’ of five darts spreading out towards the shoulder blades which I particularly like. The cuffs each have 3 similar darts, the details on this pattern has simple but so stylish.
This post was originally published last year by Minerva who generously provided me with a nice firm Ponte Roma in a plain navy to make the Dawson in, it would also work very well in a boiled wool, felted wool, Melton, not a loose tweed though as they can start to fray and you’d lose the details too much in the weave. Anything fairly structured and stable would effectively show off the style lines. You could get some interesting effects with checks or stripes if you want a challenge! I’d wanted to make another version for a while because I’ve had really good use from the navy one, I hadn’t got around to finding any specific fabric for it but then I hit upon the idea of using a single old heavyweight cotton curtain that used to keep the drafts out by our front door. It had long been replaced for this task but I just had it folded up underneath the heat-reflective mat that I use on my cutting table. In order to maximise the fabric in the curtain I undid the deep hem and the sides, and removed the tabs at the top. I gave it a wash to clean it but also to, hopefully, stop it shrinking later on.
Areas like the pocket edges and the neck need stabilising with some iron-on tape or strips of interfacing as per the instructions, especially if you use a knit fabric like Ponte. I would recommend stabilising the shoulders with seam tape or scraps of ribbon to prevent stretching too. I used a specific needle for stretch fabrics and you could use the ‘lightening’ stitch to sew with if your machine has it, or a very straightened out zigzag. If you do use boiled wool the layers could be quite thick, use a straight stitch but you may need to lengthen it a little more than usual.
The pattern comes in eight sizes which are not numbered in the conventional way, CL opts for letters instead, so you work from your own body measurements to choose which size should fit you. I cut and sewed a size F originally which was quite generous, for the newer version I’ve cut the next size down. I misjudged how generous the ease is in the garment so I usually wear the Ponte version layered up over jumpers or sweaters on warmer cool days if that makes sense. At the end of the day it’s intended as a casual coat so don’t make it too small as you’ll always be pulling it closed across you. The sleeves are nice and roomy too, I’ve noticed some coat/jacket patterns can be a bit snug around the bicep for me which is a bit dispiriting, I’m hardly a muscle-bound hulk! Just check before cutting out if you’re happy with the sleeve length too, I probably could have added just 3-4cms because it feels the tiniest bit short on me.
The pattern goes together beautifully and all that tweaking in the sampling stage is borne out in the final version. I found the instructions pretty clear, they are mostly photographs and there are some really useful hints and tips which will come in very handy if you aren’t that experienced in your dressmaking yet. Make sure you transfer your markings for the pocket pivot point for example so that you get a crisp finish for the corners.
You could top stitch all the darts down, possibly in a contrast thread if you like, but because the Ponte had a slight stretch I didn’t do this on mine. I did top stitch down the front facings though and caught them down in a couple of places on the inside to stop them flapping.
For the ochre version I topstitched more of the seams, I confess that I was incredibly slovenly and used up various threads in my collection so not all the stitching is the same colour…oops! Incidentally I didn’t use top stitch thread, instead I used the triple straight stitch which looks very similar although it is quite thread-hungry (hence the non-matching!)
This time however I didn’t top stitch the front facings down, I adopted a different approach. As it’s an unlined coat so all the innards are visible I used some ribbon to anchor the facing down in a couple of places. I chose to do this because I know from experience that when you’re sewing through several thick layers the triple stitch (which is a set length on my Pfaff and not adjustable) it can lead to puckering which doesn’t look so nice. Try a sample before you go ahead if you aren’t sure, that’s a LOT of slow unpicking if you don’t like it after all.
I finished the hem by hand using a herringbone stitch rather than machining it for the same reason that I didn’t top stitch the front facings.
I think the Dawson is a well-drafted and executed pattern from an independent designer (and CL’s art work features herself so it squeaks into the #so50visible category!) The Minerva Ponte Roma works well for the soft tailoring, using my old curtain gives the slightly cocoon-shape a little more definition. It shouldn’t be too difficult to do an FBA if you need to either. I’m much happier with the fit of the ochre one, but I love the navy and will still wear it regularly too.
Because the Dawson is a loose cocoon shape it would make a beautiful evening coat in a glamorous brocade, to go over the top of your evening outfit, denim would look great too (Have a look at my Simple Sew Cocoon jacket in denim here)
I guess this was also a useful exercise in upcycling, the curtain was years old and not being used for it’s original purpose so I thought why not give this a try. If I found I wasn’t mad about wearing the colour after all I know it’s 100% cotton so it would dye, I might come unstuck with the polyester sewing thread though which would take up the colour differently-it’s hardly Saville Row standard though! The Dawson took barely two metres of fabric (the front facing is helpfully cut in two parts which helps reduce the fabric usage, and of course you could always use a contrast fabric anyway) it doesn’t instruct you to use interfacing on any of the collar or facing parts but I did, just to stabilise the fabric a bit.
So, here we are TWO YEARS on from the first SewOver50 post, on August 18th 2018, and the account now stands at nearly 21K members worldwide!
Personally, I’d really like to thank Judith and Sandy for the amazing amount of work they undertake so graciously in order to steer the Mothership through some interesting and turbulent territory, especially the second half of these last twelve months.
We were all trundling along in our own way when suddenly, in early 2020, the world went very weird indeed. As the impact of Covid-19 started to take effect many of us were locked-down at home, some still working but in a whole new way, reliant on technology to carry on, it was an extremely stressful time for many who could have no contact with their loved ones or friends, lots of sewing-related events we so enjoy were cancelled or postponed. Many of us found that our sewing and creative making was a safe haven amid what was going on around us. For example, did you make a pouffe? I had the luxury of being able to sew whenever I wanted, because I couldn’t go anywhere, and I noticed others embarking on this project so I took the opportunity to use up SO many scraps of fabric and stuff them all into a footstool, I made my own pattern but I know many of you used the ClosetCore free pouffe pattern. I know many others couldn’t sew as often but, from chatting with friends, the time that they were able eke out to sew was vitally important to them, helping them to de-stress and shift their focus for a while. Shopping for fabrics, patterns and haberdashery online became a way, almost the only way, of supporting some of our favourite businesses, as people found new ways to adapt and do business. Sales of sewing machines worldwide increased exponentially with many manufacturers and retailers struggling to keep up with demand. Some of us had sewing sessions with our friends via Zoom, which was occasionally technologically-challenging but it enabled us to be in touch with each other whilst participating in our shared interest. I’m not going to dwell here on the pandemic though because it’s been different for all of us, sewing and being in touch with my sewing friends around the world has been an absolute lifeline for me personally. In fact, rather than watching the all-too-overwhelming daily news stories, it’s enabled me to hear and appreciate what people I feel I’ve come to know have been going through. At one stage it seemed anyone who was able to was using their sewing skills to help with the desperate shortages by making scrubs here in the UK, and possibly elsewhere, and mask-making has become something that people with little previous sewing experience have found themselves being able to contribute. Face coverings have become compulsory in many places now so this will be an ongoing activity in future.
Moving on, as a group @SewOver50 has always strived very hard to be inclusive of anyone who wishes to follow along, after all, part of the reason it started in the first place was because we felt somewhat excluded from sections of the sewing community by virtue (?!) of our age. Following the murder of George Floyd in the US we were all called to question the part we play in our world, even within our sewing community we had to examine our consciences to ask if we were doing enough. #BlackLivesMatter was rapidly followed by #BlackMakersMatter and there is now an Instagram account @BlkMakersMatter where you can see, and follow and support, the massive diversity of BIPOC makers, and not just sewers but crafters and makers of many beautiful things. Many of our wonderful stalwart SewOver50 followers including Diary of a Sewing Fanatic are vocal advocates, I’ve always got time for Carolyn’s no nonsense plain speaking! We shall endeavour to continue reflecting our membership, and involve a diverse range of contributors and guest editors in the future. If you have ideas for future topics, especially if you think we’re missing something important, do please let us know.
So, very briefly, that’s the worldwide picture (as it currently stands) in which there have been quite a few SewOver50-related things going on during the past 12 months too. My personal favourite was our very first, and fortuitously timed, official meet-up in London in late February. Judith was able to join me to co-host and I was thrilled that so many generous companies large and small sponsored prizes for the charity raffle we held. I think, without exception, everyone who attended enjoyed themselves and agreed we would have liked even longer to chat and create new friendships in real life, just weeks later the event couldn’t even have happened. We had high hopes of more of you being able to host your own meet-ups where ever you are in the world but that’s still not really possible, make sure you let us know if you do manage it! Above all though, stay safe!
Stalwart supporter Maria Theoharous in Sydney started her own podcast Sew Organised Style in September 2019 and she generously created a space for Sew Over 50 every Thursday! Judith, Sandy and myself have all chatted with her but you can also listen to a growing list of our fellow followers every week chatting about what sewing, crafting and Sew Over 50 means to them. It’s really lovely to actually hear their voices, talking with enthusiasm about things they are passionate about.
At the beginning of May ClosetCore Patterns paid the ultimate accolade to one of my personally most inspirational sewers, Blanca, by naming a pattern after her, it’s a stylish flight/boiler/jump suit (call it what you will) but I love her personal aesthetic and she absolutely rocks this outfit!
In the UK during the spring, and at the height of lockdown, we had series 6 of the Great British Sewing Bee to enjoy. It featured several fellow dressmakers who we can claim to be representing ‘us’ on national TV. Yes, we know they are ticking boxes to cast certain ‘types’ but at least this time it’s positive discrimination! Even so, 10 weeks went by far too quickly!
Over the year the account covered all sorts of different topics for discussion including, do you always make a toile or just happy to wing it? What are you pet sewing peeves? (cutting out and pattern tracing seemed to be top for this one!) The art of tutu making was a personal favourite, having always loved ballet and especially the costumes. Tips for better and more accurate top stitching was another goody and @SewitwithDi gave us a master class in using the correct interfacings effectively. There are too many others to mention them all but you can refer back at any time, take a screen shot of your favourites or save them to your archive for future reference.
More recently the account reached, and has now surpassed, 20,000 followers! This was marked with a giveaway where two people who had not necessarily met in real life but had formed a friendship through sewing could each win a copy of the same pattern. If you take a look at the hashtag #so50sewalong you can see some of the garments that have been made since this competition ran a couple of months ago. Incidentally, it’s worth mentioning that the #sewover50 hashtag has now been used almost 80K times up to this point, it’s an absolute wealth of inspiration and knowledge which is all yours for the taking!
I think many of us enjoyed the opportunity to look back through, and share, some of our holiday photos wearing our me-mades. Sadly many holiday and travel plans haven’t been able to happen this year so it was a lovely way for us all to virtually ‘travel the world’ over the course of a weekend. Lots of us wore those clothes anyway, even if we couldn’t leave home! The online virtual Frocktails in April was another excuse to dress up a bit, knowing our friends around the world were raising a glass to each other at (almost) the same time.
Have you been keeping a #so50bingo card? This has been an ongoing way of keeping tabs on what you have been sewing and other techniques/events you could challenge yourself to try. No pressure, it’s just a bit of fun with no time limit.
During the year I wrote several blog posts based around different topics including sewing advice for newbies (or returners for that matter) your go-to T-shirt patterns, what do you take into account with your fabric buying choices, are you a batch cutter/sewer or just one thing at a time? Judith and I both contributed videos as part of the online Sewing Weekender, this is normally an event held in Cambridge, UK but The Fold Line opened it up worldwide as an online event and it was a huge success with over 1,700 people ‘attending’ from all over the world.
We also held the second #so50visible challenge earlier in the year, we seem to be having success with getting our images reposted by lots of pattern companies which is a very good thing but notably few are choosing older models-with a few honourable exceptions-to represent their patterns in the marketplace. This is still very frustrating when you look at just how many stylish and inspirational people follow this account but if we all keep plugging away a change will come. One thing that pattern companies have said to us is that the quality of photos isn’t always good enough for them to reshare so the better, and clearer, you can make your photos to show off your makes the more likely it is to get reposted. There have been a number of posts with simple tips on how to improve your photos so why not check them out?
Most recently our own Leader Judith has written an article for bi-monthly US-magazine Sew News talking about Sew Over 50, which you can order online.
So, in spite of everything, lots of good things going on for Sew Over 50 in the last twelve months, some progress being made with representation but I’m sure you’ll agree that isn’t all the account is about. I hope you continue to find the account as inspiring as I do? Yes, we all start off by being here for the sewing but it often becomes so much more than that. Real friendships have been forged as a result, very few of us have ever met one another in real life but that doesn’t stop us identifying and empathising with each other and the lives we lead, especially during these last few extraordinary months.
I am deeply indebted to Judith and Sandy for the sheer dedication they have on our behalf, and I’d like to thank all of you for your kind words of encouragement, support and appreciation to me personally, I love being a part of this worldwide community of sewing and I can honestly say the last few months would have been very different without so many of you connecting and interacting with me in some way.
Much as I’m a big fan of sewing and wearing dresses, I do love separates too, especially tops. I think this version of the Amaya shirt by Made My Wardrobe may just have gone to the top of my favourites list! [Full disclosure, Lydia offered me my choice of one of her patterns as a PDF with no expectation of a review and I selected the Amaya with its gathered neckline, raglan sleeves and full floaty cuffs] I printed it off but then didn’t start it for a while until the ‘right’ fabric came along.
As a Lamazi Fabrics blogger we each volunteer for a number of slots throughout the year but Liana was short of a post for early August so I offered to do it. I thought the Amaya would be a good option as it’s not complex and I could probably sew it quite quickly to meet the deadline. When my eyes fell on the beautiful printed Broderie Anglaise I knew I had my perfect match!
When the fabric arrived it was absolutely gorgeous, so soft and pliable. Broderie Anglaise can often be quite stiff and crisp, which may be what you want, but I’ve also found it to be a disguise for a cheaper quality cotton fabric with lots of dressing or starch in it so do be slightly wary of very cheap Broderie Anglaise. This version is a printed soft cotton lawn which is then embroidered, there are lots of eyelets so personally I’ll probably be wearing a plain-coloured RTW camisole underneath as no one needs to see my undies or midriff thank you! This specific fabric does not have an embroidered edge which some Broderie Anglaise does, and also be aware that the embroidered part of the fabric doesn’t run right up to the selvedge, this is normal with this type of fabric. On this particular fabric there’s a wider gap down one side than the other so you may find the useable part of the fabric isn’t as wide as you would think. In other words, don’t scrimp on the quantity of fabric when choosing Broderie Anglaise for a project because you could find yourself a bit short by accident.
I opted for a UK size 14 with no modifications according to my measurements but I think I will go down a size when I make another, the fabric you choose could make a significant difference to the finished look so a soft and floaty georgette or silk crepe de chine for example would look divine with plenty of volume but a firm linen, or a cotton poplin could give you the appearance of a ship in full sail! (that may, of course, be the look you’re after!)
This fabric has a one-way design but I chose to turn the upper sleeve pattern piece to interlock better and make it more economical to cut out, I really don’t think it’s that obvious on the finished garment, always worth checking though!
It’s pretty well impossible to see snipped notches or even triangles on this fabric so, in order to tell the front of the sleeve from the back, I marked the single and double notches with long thread tacks and this seemed to work well.
I used a French seam finish on the cuffs but found there wasn’t any particular advantage to doing this, for the rest of the construction I sewed regular seams and overlocked them together.
The pattern calls for interfacing to be attached down the centre front seam to stabilise it but I chose not to do this as it would show through the eyelets, I simply neatened the edge of the self-facing with the overlocker. I had a rummage through lots of the miscellaneous trims and ribbons I’ve had from past projects and tried a few ideas out with them but in the end I only used a white cotton trim down the front and simple edging lace on the sleeves, I would have used this on the hem too but there wasn’t enough, more on that later.
I added a triple zigzag stitch to embellish the sleeve ruffle seam too.
The neckline is gathered up into a bias-cut band but instead of cutting it on the bias I used a straight strip of the printed lawn from near the selvedge. I did this because a bias strip of such holey fabric wouldn’t have worked well at all, the one drawback of the tie being cut on the straight is that it doesn’t curve around the neckline quite so smoothly but it’s fine. The tie is topstitched close to the edge so, to match the sleeve, I used the triple zigzag stitch again.
Finally I had to finish the hem, I could simply have turned up as per the instructions but I wanted some kind of pretty finish to echo the cuffs. As I didn’t have enough of the sleeve trimming, or any other edging lace which I felt worked alongside what I’d already used, I opted to try out one of the satin stitches which my Pfaff machine is capable of.
I’d never tried this before so I did a couple of experimental tests with a few stitch designs that appealed to me, I used Vilene Stitch N Tear as a backing behind it to stabilise the fabric.
This seemed to be satisfactory so I sewed the whole hem by this method a few millimetres away from the edge. The Stitch N Tear is then carefully torn away to leave the actual embroidery and then finally, as accurately as possible, I snipped away the excess fabric to leave the pretty scalloped edge.
I’m very happy with this finish on the hem BUT it’s just possible that it might not be very durable in the wash, I’m half-expecting that it might start to come away in places. If this happens then I’ll have come up with another idea but for the moment it looks nice.
I hope you’ve found my tips for working with Broderie Anglaise helpful, and things to look out for with it. It’s certainly a fabric that is having a ‘moment’ at the moment, it’s timeless and feminine and I’m looking forward to wearing my Amaya for a few years to come.
Thank you as always to Lamazi for providing me with the fabric to be able to write this, and thank you to Lydia at Made My Wardrobe for generously giving me the pattern.