My latest Backstitch project, the Ingrid dress by Homer and Howells


It’s been a while since I wrote my first blog post for Backstitch way back in January but I’m happy to say that I have loved wearing the Ellsworth shirt I made then, it’s been a great addition to my wardrobe. 

For my second post I’ve sewn a Homer and Howells Ingrid dress. Like many popular styles circulating this year it’s a loose-fitting dress but the USP of the Ingrid is its unusual asymmetric style lines. 

The front and back are both quartered by differing horizontal and diagonal seams, plus the bust shaping is in the form of tucks in the centre front seam. It pops on over the head so no zips to insert, there are inseam pockets and a choice of two skirt lengths and two sleeve shapes. 

I felt with all this unusual seaming going on that I didn’t want a busy printed fabric which disguised it (that said, you could have fun with stripes or even checks) My original plan was to use needlecord and deliberately cut the pieces in opposite directions to highlight the shading this would create. 

However I wasn’t sure that any of the colours available in the shop at the time I was making it were really very ‘me’ so I plumped for the saffron yellow Broderie Anglaise double gauze instead! [I made this handbrake turn decision partly based on having recently seen a woman wearing a similar style RTW dress made in grey Broderie Anglaise and the fabric looked great, not too ‘girly’ or twee at all]

The stitching on Broderie Anglaise fabric usually has a right and a wrong side if you look closely at the embroidery but it isn’t always very obvious. My advice would be to choose the side you prefer and stick to it throughout! Because virtually every piece of the Ingrid is cut as a single I pinned paper labels onto each one so that I didn’t get them mixed up. Alternatively you could use small sticky dots to differentiate.

I gave the fabric a pre-wash before cutting, there was virtually no dye run and no obvious shrinkage either. Because of its asymmetric shape the Ingrid is almost all cut from a single layer of fabric so I would highly recommend keeping each pattern piece attached to the fabric until you’re ready to use them, or label them as I’ve suggested earlier. [Incidentally, if ever you’re short of fabric for a project, check if you can cut it out of a single layer rather than folded, it’s always more economical…just make sure you mirror everything as necessary] Helpfully Backstitch sell their fabrics in 25cm increments which can mean a lot less wastage, I bought 2m25 for this dress.

I pinned rough labels to the pieces so that I knew exactly which one was which.

I found the instructions and diagrams for construction nice and clear and very straightforward, do read them through a couple of times first though because I made assumptions about the order of making in a couple of places which would have led me up the garden path and some unpicking. The right and left dress parts are sewn tops to skirts before joining vertically at the centre front and back. Some of the seams which would normally match one another on more conventional styles don’t on the Ingrid because of the asymmetry but if you start pinning at the top of each seam down to the hem you should be fine. 

The fabric sewed up nicely although be aware that the weave of double gauze causes it to have a little inherent stretch so try not to pull it about too much during construction, and pressing causes some of the natural crinkles of the cloth to flatten as well but they will bounce back after the next wash. 

I made a couple of other small deviations from the pattern by using self-fabric bias binding instead of the neck facing. I cut a bias strip 4cms wide, folded and pressed it lengthwise before sewing the two cut edges to the neckline on the dress. Next, I understitched the seam to the inside then finally topstitched it down to finish. I also chose to sew my own thread loop for the button at the back neck rather than try to make a rouleau loop with such ‘bobbly’ fabric, I was delighted to find a button in the shop which is a great match to the fabric colour. 

marking the centre front point on my folded binding
Pinning the bias binding in position
Close up of the centre front seam details

I wasn’t convinced that either skirt length would be quite right on me so I went somewhere in between, finishing a little below knee length (I’m 5’5”) I wanted longer sleeves too so I used a bell-shaped pattern with a cuff which I had drafted myself for a different dress earlier in the year. 

My sleeve has a fixed cuff with gentle gathers (incidentally, the colour here is paler than in reality, the outdoor photos of the finished dress are much more accurate)

Finally, I turned up the hem by 2.5cms and then used one of the huge range of embroidery stitches on my Pfaff machine to sew it up, it took a while to go all the way around the hem but I love the little detail it gives. 

The hem is finished with a machine embroidery stitch

The only fitting change I will probably make if/when I sew another Ingrid is to slightly reduce the width of the shoulders, the sleeves cause them to droop off my shoulders a little but it’s not a major issue. I sewed the UK14 with no fitting adjustments other than the length and it’s very comfortable.

The back seams are asymmetric too
The button and hand-sewn loop

Thank you to Backstitch for providing me with the fabric and supplies to sew with by means of gift vouchers, the Ingrid is not currently stocked in the shop though. Broderie Anglaise might not be typical winter fabric but I love the sunny colour on a miserable English day.

I hope you’ve found my review helpful, until next time,

Happy sewing
Sue

Merchant & Mills Fielder Top

The Fielder top and dress by Merchant and Mills has been around for at least six years I think but I only bought my copy from Anne NewVintageSewing just last year when she was having a destash sale.

Essentially it’s a raglan cropped-sleeve sweatshirt or dress with ribbing cuffs, hem and neckline. The sleeves have darts at the shoulder to give them some shaping and the neckline is quite scooped out. Most of the sweatshirts I’ve made in recent years have been quite baggy and over-sized so I thought I would try the closer fit of the Fielder for a change. Based on my own body measurements and the finished measurements given on the packet I opted for a UK size 12, and I lengthened the sleeve to be wrist length.

I bought the unusual ‘quilted’ fabric from the M&M stand at the recently-revived Knitting and Stitching Show at Alexandra Palace in London. It was so good to be able to browse a whole selection of stands once again, it had been over 18 months since any of us were last able to do that. The colour reminds me of old-fashioned sticking plasters, the triple-layer fabric is a clever weave but the loose threads through the middle layer do come adrift quite easily. Because of this I overlocked every piece around its edges to prevent further disintegration. I also stay-stitched the neck edge before it had a chance to stretch.

I couldn’t get any ribbing in a colour I was happy with but I found this brilliant wide elastic in MacCullogh and Wallis with it’s pink/beige stripe blending into black.( Can’t find this exact product on their website, I bought it in-store, they do have similar items online though) The next challenge was how to attach it without losing any of the colours.
I tried out laying the elastic over the top of the overlocked edges like this and that seemed satisfactory. I lined up the pink stripe with the O/L stitching underneath which created a suitable overlap.
I tried out a few stitch options and settled on this closed overlock on my Pfaff
It calls for the blindhem foot to be used which meant I could follow the red guide along the stripe.
The finished stitch is nice and stable and looks good too.
The next challenge was neatening the neck but, as you can see from the photo above, the width of the elastic meant it stood away from the neck and was all wavy.
I pinned it on though and had a ponder on how to solve the issue while I went out for a run….
I came up with the idea that if I could get rid of the fullness on the outer edge (like I’ve pinned it out here) then that might work. I sewed the elastic on in the same way I had on the cuffs and hem and pinned evenly and in alignment with each line on the check design.
Next I folded and pinned each pleat evenly, the chalk line and pencil marks where I would start and finish the line.
I used the width of the presser foot as a starting point to sew down to the bottom of the triangle.
a completed triangle.
This is how it looked after I’d sewn all the triangles and I was pleased with the result. The idea worked but now the triangles weren’t flat inside against my neck.
I tried topstitching each one from the outside to see if it would flatten the triangle sufficiently.
It worked! I pushed them all the same way instead of having some going in one direction and some the other.
The end of the elastic was folded over and stitched with two lines at the CB, it ain’t perfect but I’m pretty pleased with end result! I thought I was going to have to settle for an alternative ribbing/binding of some kind on the neck which wouldn’t have linked so well with the hem and cuffs so I’m delighted with how well this has worked out.
I added this gorgeous little label given to me by my friend Alana (and available from Rosy Little Cheeks) on the back, I think it’s perfect, and true!

I haven’t mentioned the rest of the garment construction because it’s a very straightforward sew, I just made it a bit harder for myself…but in a good way.

As I said in an Instagram post, whilst I’m really pleased with he finished result as a garment, I’m not 100% convinced about the fit yet. The fabric is an unusual alternative to traditional sweatshirt fabric, although it creases more and there’s no stretch either but I think it will come to like it. I’ve got plans to make a plain white button-up shirt to go under things this winter (most of mine are over-sized like the sweatshirts!) so I’ll probably layer it up under this, or a roll-neck perhaps?

Anyhoo, that’s one way to elevate a plain top into a slightly more interesting one (IMO!)

Until next time, Happy sewing

Sue

Simple Sew Palazzo Pants updated

In 2019 I decided to try something different to dresses from the Simple Sew pattern collection for my blog post so I chose the wide-legged Palazzo pants. 

I always have a look at any posts or reviews about a particular Simple Sew pattern first to check if there are any pitfalls I should look out for which might influence my decision, or how I tackle making it, and the overall opinion of trousers was positive. I sorted out some fabric from deep in the stash, it’s a viscose from the now-defunct Adam Ross fabrics which has a good drapey quality, although I know it will crease so I’ll wear these permanently standing up! 

There are only 4 pattern pieces to the trousers-front/back/waistband/pocket- which makes them very simple to lay up and cut out, you could even leave out the pockets if you’re short on fabric but why would you leave out pockets?! 

I checked my measurements against the chart to decide my size, I also measured the pattern pieces to get some idea of the ease involved but I was optimistic they would be generally OK. If you’re very unsure, or between sizes, I’d suggest you make a toile that’s about mid-thigh in length to check the fit and comfort around your waist, hips and body length. Leave out the pockets at this stage, there are darts in the back and the front is flat, you could insert a zip in the back if it makes things easier to fit yourself but I didn’t bother. Always sew a toile as accurately as you would the garment itself because if you don’t bother cutting properly or following the seam allowances how will you know where the problems lie? That’s the whole point of a toile! Make any adjustments on the toile and transfer the changes to the pattern pieces. There are no lengthening/shortening lines marked on the midriff area of the pattern so I suggest, if you need to make either of these changes, drawing a line at a right angle to the grainline at a point midway between the waist and crotch level. Fold out or add in length through this line. There is a lengthening/shortening line for the leg length however.

It wouldn’t be a Simple Sew pattern if there weren’t some errors or anomalies to keep you on your toes and this is no different. On the back piece the pocket placement notches are only printed on size 8 and none of the others. Either transfer the markings to your size or remember to snip them when you’re cutting out the back.  

The notches don’t feature on all the size lines so transfer them across as required.

The lay plan for cutting out shows the main pieces interlocking, which is fine if you have plain or multi-directional fabric but don’t forget to keep the pieces running the same way if you have a distinct one-way print. Also, I didn’t cut out the waistband until I was happy with the fit of my trousers as it’s very shaped piece and if it’s too big or too small you’ll probably need to cut another. Don’t forget to make a snip for the centre point on the waistband, it could have done with a notch for the side seam position though as there isn’t one so it’s a bit of guesswork.

I’m not normally an advocate of overlocking the edges until they’re sewn up [because if you aren’t careful you can easily lose too much seam allowance in the trimming and when you join pieces together you could start to make the garment too small, plus your notches disappear] but, as many of the pieces here require the seams pressed open and flat, I overlocked most pieces first this time. 

You will find that for instructions 4 and 6 the words don’t match the diagrams but the drawings are correct 

Next the pockets go in (unless you wish to check the waist/hip fit first in which case tack or machine baste the side seams and leave the back open where the zip will be inserted in order to try the trousers on) The description for the pocket insertion is a bit vague, I’ve made a second pair since writing this piece originally and found it quite unsatisfactory which is why I have updated my advice.

Neaten the lower edge of the pocket bags first then pin to the trouser fronts matching the ‘opening’ notches. Next stitch in place from the waist to the bottom edge of the pocket bag using a 12mm seam allowance (see my notes on the photo above) Repeat with the trouser backs, then neaten the seam edges all the way down enclosing the pocket edges too. On the front only, understitch the pocket opening. Now you can pin the fronts to the backs and sew the side seams shut using a 1.5cms seam allowance, not forgetting to leave the pocket opening unstitched! Finally, carefully sew the bottom edge of each pocket bag closed otherwise your sweets will fall out inside your trouser leg!

After I’d assessed the waist size (comfortable to loose) and crotch length (comfortable) at this point I cut and interfaced the corresponding waistband [for some reason there were two waistbands printed out but I could find no discernible difference between them so just ignore one and cut a pair in fabric plus one interfacing] 

The reason the waistband goes on before the zip insertion is because the zip runs right up into the waistband to finish at the top, there’s no overlap allowed with button or hooks and eyes. You could use the overlap method if you prefer but you’ll need to add some extra length to the waistband on one end to allow for the overlap. 

The lack of indication of the side seams on the waistband means you’ll need to pin carefully to evenly absorb any fullness of the trousers to ensure a good smooth fit to the waistband. [the side seam is probably at the halfway point but not necessarily, especially if you’ve made any fit adjustments to the waist] 

With the benefit of hindsight I would make the waistband in two pieces, a front and two backs with the join at the side seam. This is for two reasons, first, it will allow you to make adjustments for fit more easily and, secondly, I’ve found the centre back has become slightly pointy and misshapen both times I’ve made these now. I believe this could be because the length and curve of the waistband means that it the centre back is very off grain, usually the centre back seam would be cut on the straight grain which gives it stability.

The instructions and illustrations for inserting the zip are reasonably clear however there seems to be a contradiction with an earlier instruction which tells you to sew up the back crotch seam. Illustrations 13-15 appear to have the CB seam unsewn and 16 tells you to sew it up after inserting the zip but previous diagram 6 tells you to sew it up! No wonder I got in a muddle!! My suggestion would be, if you’re using an invisible zip as suggested, leave the CB seam unsewn AND ignore instruction 11 to sew up the inseam until after you’ve inserted the zip. Alternatively, use your preferred method of inserting an invisible zip. Before sewing the waistband down I added two hanging tapes to each side seam so that I had an additional means to hang the trousers up if needs be.

On my second pair I’ve added a small button and loop inside the waistband because I found the zip a bit of a faff to do up without anything at the top of it.

you can also see here how the waistband rises to a slight point on each side in spite of it being fully interfaced. It isn’t the end of the world but I’m a bit cross it’s happened a second time, CBA to fiddle with it too much though…

Hopefully you’ve now arrived at a finished pair of trousers which simply need hemming. After checking the length wearing shoes (they come up pretty long) you could use the simple rolled hem finish as per the instructions or, as I did, leave a sizeable hem of about 5cms to give weight to the very flared leg width. I overlocked the edges to neaten and then used my blindhem stitch with the appropriate foot on the machine to finish [incidentally the photo is of a different project] I don’t use this technique often but it’s a good, and quick, finish on hems that don’t have too much, if any, curve. You could also slip hem by hand of course. 

Different project but still blind-hemming set up

The Palazzo pants are worth persevering with as they have a pleasing smooth fit over the waist and hips which is very comfortable and the leg is wide without being crazy-big. You could shorten them to culotte length very easily, they would work well in a variety of fabrics including linen, chambray or crepe, fabrics with a bit of drape and fluidity will look nicest as you don’t want to look like Coco the Clown!

I’ve made my second pair from a remnant of printed linen/viscose mix I bought from Lamazi recently.

I’m wearing them here with a top made from broderie anglaise that I found in a whole collection of fabric I was given by a friend. Her mother had been a wonderful dressmaker and I found the fabric pre-cut as this simple top which so I just sewed it up.
I’m wearing them here with one of my trusty Camber Set tops from Merchant & Mills
Same Camber, different trousers!
I cut this pair slightly shorter overall so that they aren’t so long if I wear them with flat shoes.

Overall I’m pleased with these trousers, they are a good fit and make a nice alternative to a skirt or close fitting trousers especially in warm weather.

I noticed that this particular post gets a huge amount of traffic so I hope this update clarifies any issues you might have had with the pattern. In fairness, it might have been updated and corrected since my copy was produced in which case you may be able to disregard some/all of what I’ve written!

Until next time, happy sewing

Sue

Box pleat shirt from Trend Patterns

I’ve made loads of different clothes over the decades but actual shirts for myself have not tended to be among them. I’m not sure why, possibly because I had to wear boring school shirts for years and years, and for a while I had to wear a uniform when I worked for the John Lewis Partnership so my personal preference has tended to softer blouse shapes. That said, I love to see a crisp white shirt especially when it’s given an inventive twist. It’s a wardrobe staple and yet there’s always room for a new version. 

Lucy at Trend Patterns has just released the first 3 patterns of what will become a shirt collection and each is available printed, as a PDF or as a complete kit with pattern, fabric and trims. TPCSH1 is a feminine Pussy bow top with shirt sleeves and a ruffle hem, TPCSH3 has stunning gathered ‘angel’ sleeves which really make a statement whilst the body is kept simple and traditional so that the sleeves do all the talking. 

Lucy offered me the kit of TPCSH2 to try out, it is a box-pleated front shirt, deceptively simple to look at but those details take a little time to get right. It’s classified as ‘moderate/hard’ and I would agree, not because the elements in themselves are especially difficult but each of them needs some experience and precision to execute so I wouldn’t recommend this as your first shirt project. 

The kit comes with enough good quality plain white cotton poplin to make up to the largest size of a UK 22, along with Trend-branded buttons (a nice touch) and iron-on interfacing. All you need to provide is your own thread! 

I started off by taking my measurements and comparing them to the sizing chart, there is also a chart giving you finished garment measurements too which is helpful because it will give you some idea of how oversized the shirt will be when it’s finished. I made a UK 12 and as you will see from the finished photos it’s a very generous fit, to be honest, if you want a close-fitting shirt then this particular pattern won’t be the one for you. 

I opted to trace off the pattern, there are two separate fronts, right and left, and a whole back plus sleeves, yoke, cuffs and collar. There is no pattern piece for the bias binding for the sleeve placket, you just need to cut yourself two bias strips approximately 30cms x 4cms. The right and left fronts are the same except for the extra on the centre front which creates the folded fly with concealed buttonholes. I traced off one front then, to save some time and to ensure they were identical, pinned it to more spot and cross paper before cutting them out together so that I had a mirror version with the additional front added. It’s really important to trace the front very carefully because of the three box pleats, if they are each a bit off you risk the pleats not sewing together accurately which will leave you scratching your head. There are a lot of drill holes to mark the stitching which will eventually hold the pleats in place, don’t be tempted to miss any out because they are also really helpful when you’re folding and pressing the pleats in position. You could choose to trace just half the back to save paper if you intend to always cut it on the fold anyway but having a whole piece gives you the option to have the fabric out flat, besides, it’s almost always more economical to cut fabric out as a single layer [this can be especially helpful if you ever need to do some tricky pattern placement or matching]

Because the fabric is plain, placing the pattern pieces and cutting out was a breeze-no pattern matching, yay! I spent quite a while making traditional tailor’s tacks for every single one of the drill holes. You could use a washable or some other kind of disappearing marker pen if you are confident that it definitely won’t come back to haunt you but I wasn’t going to take the risk on plain white fabric! 

In the past I’ve occasionally found some of the earlier Trend instructions a bit tricky to follow but the more recent ones have illustrations rather than photos and I found this set very clear. My biggest piece of advice would be to read then re-read the instructions before you start, and to highlight anything that you know you’re going to have to really concentrate on, this isn’t a race after all. 

Constructing the fly front and button stand first, including the buttonholes, was satisfying, I often feel like I’ve run out of steam by the end of any project which requires buttonholes and it’s a bit of a chore by then but this gets it out of the way nice and early. [I should add at this point that I started out sewing with a fine size 60 needle so as not to leave too many noticeable puncture holes in the plain fabric if I went wrong or needed to unpick. However, this size needle kept skipping stitches for some reason so I went up to a 70 and had no further problems]

transfer all markings and instructions to the paper pattern if you’re tracing it off. I made tailor’s tacks through every drill hole

My second piece of advice would be to press your pleats on the ironing board if you possibly can. I only have a small heat-resistant board in Threadquarters which meant I was constantly moving the fabric which was not ideal, it was so much easier on the ironing board because the whole piece fitted on. Do not rush this part, with pure cotton fabric you can have the iron on pretty hot but do be careful of your fingers with hot steam. Pin, tack or Wonder Tape the pleats in position once pressed if you want to. 

pressing the pleats on the ironing board, the snips top and bottom along with the tailor’s tacks will help you get each one in exactly the right place.
In progress-making the bar tacks

The instructions are to stitch down each pleat according to the markings using a few stitches. I did quite a lot of testing using a variety of decorative stitches for this before I committed to the bar tack. The next challenge was getting each of those bar tacks (30 in total!) central over the pleat. My machine comes with a number of feet which are used in conjunction with the decorative stitches and one of these has horizontal red lines which proved very helpful in getting lined up for every bar tack. After making a few of these bar tacks I ‘got my eye in’ so I could tell very quickly where to start each stitch, having the needle stopping in the up or down position is an absolute essential feature on my machine for me and it was brilliant during this, being able to lift the foot to check I was sewing in the correct place without the work shifting was so helpful. The photos will hopefully make my method clearer to follow. It’s vital to take your time and be as accurate as possible during this stage because the box-pleats are the USP of this shirt and it will obvious if they are off-kilter. I sewed in white thread but you could use a colour, or even hand embroider to give your shirt a totally original look.

testing various stitches including triple straight stitch and arrow heads, the difficulty was going to getting every single one central over the pleat

Incidentally, Trend will be creating a series of video tutorials to help so I suggest you check their Instagram account or the website for those. Also, there was a slight problem with pattern markings for the back box pleat which were incorrect. This has been rectified but if you bought a copy very soon after release you might find you have to scratch your head a little, the notches were in the wrong places. Check the website if you’re in any doubt.

the right front, including the fly, taking shape
the shirt with the side seams now sewn up, ready for the sleeves to go in
sewing the continuous binding to the sleeve opening. the instructions don’t call for it but I like to sew across the top of it at a 45 degree angle to encourage the binding to stay on the inside
close up of the finished front
all done
close up of the finished bar tacks

I followed the order of construction to complete the shirt (I usually do the first time I make a pattern) but personally I would put the collar on after making the yoke. I like to do it before the side seams are sewn up or the sleeves are inserted, unless there’s a technical reason not to obviously. 

the finished back yoke
I popped a bar tack in the middle of the back to hold the pleat in place, this hadn’t had a proper press yet

Everything came together really well, I’ve always found Trend patterns are accurately drafted so I know the pieces will go together well without major discrepancies-this is why it’s so important to trace off carefully if it’s your preferred method, if seams or notches don’t match up you won’t know where the fault lies [the same applies to accurate cutting out too] 

The sun came out so we could take some outdoor photos, I’ve paired the shirt with my much-worn Megan Nielsen Ash jeans
is it a bird? is it as plane?…
I’ve pressed the pleat now

Clearly not everyone will want to make a shirt that is going to take a sizeable amount of time to construct, or to launder afterwards for that matter, but if we only made simple loungewear for ever then the art and skill of making our own clothes will be lost, just at a time when so many people have discovered, or rediscovered, the joy of sewing for themselves. There will always be a place for a classic white shirt and Trend has created a small but growing collection with original twists on the genre. The last year has been so tough for small business owners so I really appreciate being given this kit to try out, I wasn’t under any obligation to review it other than share some photos but personally I have no problem with sewing and writing about it. I will always try to give you a balanced view and if I can support a little business by giving them some positive exposure then I will. Alongside that I’m keen to demonstrate that a design-led style doesn’t have to beyond us ‘ordinary’ sewers either, if you like it then sew it! 

I hope I’ve given you some idea of what will be involved in making the TPCSH2, if you’re looking to push your skills on a bit this could be a good project. Maybe you need/want a plain white shirt in your wardrobe [amazingly I didn’t have one in mine, just a couple of short-sleeved ones] I might layer this with a sleeveless tank top over it, or a waistcoat could look interesting. This is a typical cotton poplin shirting but you could use a variety of fabrics, you could have fun with graphic prints or stripes, try something soft like double gauze or a crisp linen? Or what about harvesting the fabric from several well-worn mens shirts to make a more patchwork look. Take your time though and enjoy the process.

I’ve got a long-sleeved T-shirt under it because it was a chilly day and it will be perfect for the day I can return to the V&A. I don’t know about you but I’ve really missed putting an outfit together to go on a nice day out, deciding which of the lovely garments I’ve made that I want to wear and how I’m going to accessorise them. It seems such a small silly thing to miss but I shall be so glad when I can start doing it again.

Most of all, thank you to Trend for giving me the opportunity to try the kit, until next time,

Happy Sewing

Sue

a multitasking Festive outfit

The Festive season is often a reason to make, or buy, a special new outfit to wear for office parties or Christmas Day but this year’s Festive season things will be very different for most of us. I don’t want to be entirely negative though so, as part of the Lamazi blogger team, I thought I’d make something which is a little bit Christmassy but will double up as a ‘regular’ winter dress too. 

I’ve chosen the cord velvet from Danish Design in a gorgeous shade of aubergine-I’m always a sucker for purple-but it comes in several other beautiful rich shades including a sumptuous gold and a stunning teal too. I picked this fabric because it’s a medium weight stretch jersey and has soft pile which makes it lovely to the touch. I’ve made a dress but you could easily make tops or wide-legged pants in it, or babies and children’s clothes too because it’s washable and crease resistant. 

Whilst I love a complex make to really get my teeth into I felt this wasn’t a garment which warranted lots of time. Making a special Christmas once-worn garment wasn’t appropriate any longer so I wanted something quite simple but adaptable and for that reason I’ve picked the Somerset T-shirt by Maven Patterns. I’ve made a few of these now, the bones of it are beautifully simple, it has a self-neatened bateau neckline, a slightly fitted silhouette and four sleeve options. I’ve chosen the Bishop sleeve with a long cuff but I’ve hacked the sleeve to make it even fuller, and I’ll lengthen the body to create a dress finishing below the knee.

Another idea was to add a flared skirt which looks nice but didn’t think I would use it as much as the straight version.

The Somerset has excellent very full instructions with lots of tips and advice to get a good finish. There’s a useful sheet to write all your information including body measurements and fit alterations, and a fabric stretch gauge to check you have enough stretch for the pattern to fit properly. You can also list the needle type and size you’ve used, stitch type and length and anything else you might want to remember for another time. 

To increase the size of the sleeves I took the bishop sleeve pattern and drew 5 vertical lines from each of the notches from shoulder to hem. Each segment will become slightly wider as it gets nearer the bottom edge so make sure they are even in size.

Cut a piece of spot and cross or tracing paper bigger than the pattern as it is, mark a grainline running right down the paper and then lay the pattern piece on top of it, matching the grain on the pattern to the grain line you’ve just drawn. Next, I carefully cut up to the top of the marked lines taking care not to snip right through at the top, keep it attached by a tiny amount to act as a pivot point. [If you don’t want to cut your original pattern piece I suggest you trace off a new one to use instead] Then you splay the hem edge apart by a few centimetres each, I added 2.5cms between the each of the ‘side’ segments and 5cms to the central one. By doing this you’re adding fullness at the hem but not altering the sleeve head. You could put additional fullness to the sleeve head by opening the top edge too if you wanted. I lengthened the sleeve by 5cms too so that it would have plenty of blousy fullness into the cuff. 

Trace around the new shape using a tracing wheel or pencil and cut out the new piece transferring all markings. One final change I made was to add a bias grainline because I knew I wanted to play with the stripe direction of the rib on the fabric.

I had pre-washed my fabric and partly tumble dried it on ‘low’ before letting it dry completely on the clothes airer, it seemed to survive the experience just fine. 

I made an arbitrary choice of how long to make the dress by simply holding the tape measure at my shoulder and seeing where it came to at about mid-shin! I attached another piece of spot and cross to the bottom of the front and back pattern pieces and drew on the skirt length I wanted, plus a generous hem. I knew I would have to make some adjustments to the hip and thigh during the fitting stage, just make sure that the hip and thigh measurements are plenty big enough because you can always remove some, it’s much harder to add later! 

The ‘cord’ runs across the width of the fabric and I wanted the rib to run down the length of my dress which meant I had to fold the fabric across the width. Try not to twist the fabric if you have to fold this way, I marked a single rib by following it across the width with pins so that I can see it clearly. Fabrics like corduroy, velvet or velour have a pile or ‘nap’ which will shade so if you cut some pieces facing one way on the grain and some pieces running the other way then you will end up with a garment that looks like it’s been made with two different colour fabrics, even though you know that isn’t the case. If you’re unsure what quantity of this type of fabric to buy go with the ‘with nap’ amount on the pattern information and follow the one-way layplan to cut out.

I marked the rib across the fabric with pins so that I could be sure it was folded correctly and would not be twisted.

Once I’d cut all my pieces I followed the making instructions which are very comprehensive. If you have a walking foot for your machine I strongly recommend you use it because velour like this has a ‘pile’ and has a tendency to ‘creep’ as you sew so you might find that it starts off with all the edges matching but by the time you get to the other end the two fabrics are no longer matching. I also strongly recommend you tack any seams you are unsure about. You could use a million pins but by the time you’ve done all that you could have basted it in place which does the same job and usually more effectively. I was able to coverstitch the neck and the skirt hem on the Pfaff Coverlock 3.0 I have on loan as a brand ambassador but it works just as well by overlocking the raw edges and twin-needle stitching them down, or zigzag and twin-needle, or two rows sewn singly if you don’t have a twin needle. When it comes to pressing a fabric like this, if you don’t have a special needle board (and few of us do) then you should press on the reverse at all times. You could place a towel on your pressing surface and lay the fabric on top so that the pile of the cloth is against the pile of the towel which will help protect it. Use a pressing cloth as well. These tips will also apply to regular corduroy or any non-stretch fabrics with a pile too.

The bell of the sleeve is gathered using shirring elastic which helps to retain some of the stretch required for the cuff. 

Once the sleeves were in I sewed up one side seam directly on the overlocker and then pinned the other side seam to fit myself. This was because I didn’t know if I’d need a split at the hem to be able to walk in the dress and I didn’t want to end up with loads of unpicking!

First I tried it right side out to get an idea of how it was fitting initially, then I turned it inside out to pin.

I looked at the fit in the mirror first of all and the sewn side seam was quite wavy, this could be cured by either adjusting the differential feed on the overlocker so that it doesn’t happen, or you could stitch the seam on the sewing machine and then overlock the edges [This is what I opted to do because I could see I had to take a fair bit off the side seams anyway to achieve a fit I was happy with] Then I put the dress on inside out in front of the mirror and pinned out the excess. I turned it right side out and tried it on again to check the fit, then finally sewed both side seams on the sewing machine, I used a ‘stretch’ needle, a ballpoint or jersey needle performs the same task. Either use a short straight stitch or a straightened out zigzag, make some samples to see which works best for your particular fabric. 

Now I tried it on the dress inside out to adjust the seams
I pinned out a fair bit of the side seams to give more shape through the waist and hips.
still Inside out
Finally I put the pinned dress back on the right way around to check I was happy with the fit before making the adjustments.

Lastly, the cuffs go on and the skirt is hemmed. 

And that’s pretty much it, it pops straight over the head so no tricky closures, because of the stretch it didn’t need a split, and that means there’s room for Christmas lunch and it won’t look like a dish rag after spending the afternoon curled up on the sofa watching Christmas telly!

cheers!
I’ve dressed it down with an ancient knitted gilet plus a wide belt, long boots and my much loved Alexander McQueen scarf
I love a scarf to keep my neck warm!
It could be the strangest of Christmases but let’s raise a glass to a much better 2021

I have to say that I’m really happy with this dress because it ticks all the boxes I wanted it to. It’s comfortable but it looks Christmassy, it looks great with opaque tights, heels and jewellery, but also with boots, a chunky belt, a roll neck top underneath for extra warmth or a cosy scarf…and did I mention it’s comfortable! #secretpyjamas It also has the advantage of rolling up and going in the corner of a bag or suitcase and coming back out again not needing a press. Bonus!!

If you have a favourite T-shirt pattern you could try lengthening it into a dress, Tilly and the Buttons Tabitha from Make it Simple does that. You could browse the SewOver50 post I wrote listing loads of go-to T-shirt patterns for inspiration, or maybe copy a RTW one you already have?

At 160cms the fabric is very wide so a little will go a long way, and because it’s so soft it would be lovely for children’s wear too. It needs a little bit of careful handling but a lot of that is in the ground work. Make sure you lay it up and cut it accurately to minimise unnecessary stretching or distortion (try to keep it flat on the table or lay it up on the floor) pin or tack the seams so they don’t move about and press carefully as you go and you should be fine. 

It’s been an incredibly tough year for so many and I wouldn’t blame you for not feeling like making anything new to wear. However, if crafting and creating bring you joy and respite then you could view it as a gift to yourself, and when you choose to buy from small companies like Lamazi and Maven then you are helping them too.

Thank you to Lamazi for providing me with the fabric for me to write my review, and I hope you find it helpful. 

Until next time, Happy sewing

Sue

A few hem finish suggestions-a Sew Over 50 topic

Over on the @SewOver50 account recently I shared a few of my favourite ways to finish hems or raw edges, although course it is absolutely NOT a definitive list by any means. I thought I would expand a little here on the blog using more photos of projects I’ve made in recent years. They are in no particular order either and if I wrote a blog post about the whole garment then I’ve linked it so you can read more if you want to.

Obviously there are the usual hand-finished hems using slip hemming stitch or herringbone stitch for example, which I use a lot too, but I thought I’d share a few alternatives which you might not know, or haven’t used for a while.

I’m beginning here with a faced hem…

This was the hem of the first Refashioners project I attempted. It was a jacket made from two pairs of my husband’s old jeans and because I wanted to use as much of the reclaimed fabric as possible I cut shaped facings for the lower edge. As you can see I also finished the edge with bias binding I made from offcuts of dress fabric.
The inside of the finished jacket looked like this. I understitched the lower edge of the facing to help it roll better and also slip-stitched it in various places including the seams and pocket bags to secure the facing without the stitching showing on the front.
This is also a much more shaped facing on the hem of Tilly and the Buttons Orla blouse. This can be a beautifully neat finish on a curve, it gives some ‘weight’ and crispness to the hem too and makes it less likely to curl upwards on blouses for example.
This Orla blouse was from 4 years ago, I like the exposed zip in the back too (the instructions for putting it in were excellent if I remember correctly)

The next one is an interesting hem finish which is very useful especially if you want a quality finish on evening or bridal wear. It uses something called ‘crin’, crinoline or horsehair braid (it doesn’t involve actual horsehair any longer though!) I’ve used it here on an organza skirt for the Dior New Look-inspired evening dress I made 4 years ago. As well as a crisp finish I wanted the hem to have distinct body and wave to it so this was the ideal technique. Crin comes in various widths, this was 5cms, lots of colours too because it’s more commonly used these days to trim hats and fascinators.

Helpfully, my fabric had horizontal stripes, some opaque and some sheer so I started by placing the crin on the front of the fabric and lining it up with the bottom edge of an opaque stripe. It is stitched on very close to the edge being careful not to stretch the crin as I sew, it’s important it lies flat. By sewing the crin onto the right side of the fabric when you flip it to the inside the raw edge of your fabric is enclosed underneath. To be honest I was making up the method as I went along because my experience of this technique previously came from altering wedding dresses which used it so this isn’t foolproof. I would strongly advise you to try a few samples first so that you have the version which looks best for your particular garment. [the eagle eyed amongst you might notice in my photo that I’ve sewn the crin to the wrong side of the fabric! I obviously did it and photographed it before realising what I’d done. As this was four years ago I don’t have any other photo!]
Once the crin is turned up to the inside I slip-hemmed it by hand, it looks a bit messy on the inside because the black shows up but it’s absolutely fine on the right side.
the finished dress, it’s one of my favourites I’ve ever made, and it’s a partial-refashion too because the velvet bodice used to be a skirt!

If you’re making a wedding dress for example and mounting all the skirt pieces onto another fabric, when you use crin on the hem (or bias binding for that matter) by hand-sewing the hem all your stitches will be invisible because you can catch them just through the mounting fabric. This is a couture technique so if you look at red carpet dresses with no visible stitching at the hem this will be how they achieved it. You can apply it as appropriate to any garment that you’ve mounted to another fabric though.

The next couple of photos are where I’ve used bias binding to neaten a hem. I find this a really useful technique if you need the maximum amount of hem because you can sew a very small seam allowance. It’s good if you’re letting down hems to gain length too, on trousers or children’s clothing for example.

Sew the binding on very close to the raw edge, this was a Simple Sew Lizzie dress
Here I made my own binding which is first sewn on with a 5mm seam allowance and then understitched which is what you see here. I made this Grainline Farrow dress for a magazine review
The hem is turned up and I’ve slipstitched it in place by hand.
This is the same technique with ready-made bias binding.
the finished skirt.
My final example is the little christening gown I made from a wedding dress.

If you have fine fabric why not consider using your overlocker if you have one on the rolled hem setting? Refer to your manual for specific instructions how to adjust your machine and make samples first to ensure it’s going to be satisfactory for your particular fabric. You’ll frequently see it used on chiffon or georgette but I’ve used it successfully here on fine cotton lawn, jersey and a stretch velour. If you don’t have an overlocker you can probably achieve a similar finish on your sewing using a rolled hem foot ideally and a small zigzag stitch-as always I would urge you to experiment to see what is possible. Some of the simplest machines can still give you an interesting variety of finishes.

This is one of my variations on the Camber Set
I roll-hemmed a straight strip of fabric here which I then pleated onto the sleeve using a fork!
I roll-hemmed a straight strip top and bottom and gathered it onto the sleeve here.
An extended length sleeve on the River pattern from Megan Nielsen, roll-hemmed and elasticated

I find the next couture/tailoring technique very useful on sleeves as well as coat, jacket or dress hems. I’ve used it here on my Tilly and the Buttons tester-made Eden. I wasn’t taught this method as such, I discovered it for myself whilst doing alterations taking up sleeves for people. I haven’t ever encountered it in pattern making instructions but I think it’s an excellent way of stabilising the cuffs of coats and jackets.

Using strips of iron-on interfacing to stabilise the area where the cuffs fold up
This is felted-type woollen fabric where hand stitching is unlikely to show through but if you have a finer fabric I would make the interfacing strip wider so that I then caught the inter with my stitches and not the fabric itself. See the next photo to explain this better.
You can see the interfacing is above the hem line here and I’ve herringbone stitched it by hand. You can also see how I’ve created a chain link to anchor the lining to vent opening on the back of the skirt.
the hemming stitches aren’t visible from the outside using this technique.

For this next finish I’ve used a triple straight stitch to create the effect of top stitching on the hem, and several seams, of this Simple Sew Zoe hack I made last summer.

If you have the foot attachment and stitch capability for your sewing machine you can always try blind-hemming. I must admit I don’t use it that often, and only then on completely straight hems. There is a bit of a knack to it and I tend to only use it on a busy print which will disguise any botched bits (yes really!) or if I’m tight for time compared with any other method. It’s not quite the same quality of finish you will see on RTW clothes though which uses a specific machine to blind stitch the hem.

Personally I always think the stitches show a bit too much no matter how hard I try to get them really tiny. It’s very easy to catch a bit too much fabric, or none at all! In truth I probably don’t practice enough!!
This Regatta dress from Alice & Co was an ideal application because the skirt has a straight, unshaped hem.

I think it’s worth mentioning that I like to use bias binding to neaten necklines (and armholes) too. I particularly like this as a way of avoiding using a neck or armhole facing which can be notorious for constantly rolling into view or flapping about annoyingly. The version you can see in the following two applications is a strip which I’ve folded in half lengthways first, the raw edges are matched and sewn. The seam is trimmed slightly and snipped if necessary, then turned so that the edge is enclosed and finally topstitched close to the folded edge to secure. In both the following examples I have sewn the binding on the wrong side of the fabric so that the binding turns to the outside to be visible and decorative but you could just as easily sew it to the right side so that it turns to the inside of the finished garment.

the binding is sewn on the inside first
the binding then flips to the outside to become visible.
This dress was made for the Simplicity pattern hacking challenge last year
Instead of the usual hem on this dress I created a casing which I threaded elastic through.

I’ve have included another variation of binding on a hem to show you how it can be combined with other techniques to achieve a quality finish. I used it here on a sheer organza which was mounted onto a backing fabric of slipper satin. This meant that when I turned the hem up the hand-stitching was invisible from the outside because the stitches only went through the mounting fabric.

the hem from the inside
the finished hem from the outside.
the finished dress, I was off to a wedding!

The next technique is more usually the choice of the pattern designer than the dressmaker, although if you know a little about pattern cutting you might be able to do it for yourself. This is an example of a deep grown-on faced hem on the Trend Patterns Square dress which I’ve made twice. It works brilliantly on this dress because the hem edges are straight (square!) plus it gives real weight to the hem which is another satisfying detail.

Inside the hem the corners are mitred.

Pin hemming is a technique I’ve used for decades on fine fabrics. You can replicate it using a rolled hem foot attachment on your machine although it can be trial and error which size works best for you with variable results. I have two different sizes of foot, 2mm and 4mm and I can’t get on with either, I’ve since been told that 3mm is the optimum size for most fabrics but I’m not prepared to risk another mistake when I know I can achieve a good quality result this way instead.

Simply put, I turn over the raw edge by approximately 5mm and stitch very close to the folded edge. Carefully trim the excess close to the stitching line and give it a light press. Then turn again and stitch a second time on top of the first row of stitching. This particular example is from the Trend Bias T-shirt dress I made a few months ago.

turn stitch and trim
make another narrow hem, stitch a second time on top of the first line. Press. There will only be one row of stitching visible on the outside.

If you read about my pattern hack of the Simple Sew Cocoon dress you will see how this variation of hemming came about. I added a large chunk of fabric to give extra length to a dress that would have been too short without it. This method is probably best on a straight hem, you could use it on sleeves too.

attaching a band to the hem.
The finished dress (worn with walking shoes during lockdown!)

This next one is a very much trial and error. I used an edging stitch on my Pfaff sewing machine to hem this Broderie Anglaise blouse which I made recently.

I put a piece of Stitch and Tear behind the fabric as I sewed.
It looked like this after I finished
It will look like this on the reverse.
gently pull away the backing and then carefully snip off the excess fabric up to the stitching line.
Eventually the hem looked like this, the sleeves are trimmed with Broderie Anglaise

I’ve used a variation of a faced hem recently when, instead of bias binding, I used straight strips of fabric to turn up a straight hem on a dirndl skirt. There will be a blog of this particular garment coming soon…

I had some narrow strips of white cotton lawn lying around so I joined them to make a piece long enough to go around the whole hem.
I folded the strip lengthwise.
attach the strip to the hem, raw edges together.
I understitched it, plus there’s a band on the front which is what you can see folded over in order to enclose the facing eventually.
The band folds back to enclose the hem facing.
There’s a little bit of puckering on the reverse here but this is invisible from the front, a good press will sort that out.

To finish with is a very simple method of rolling a fairly narrow hem. Overlock the edge first using three (or even two) threads then carefully turn it once and then again so that the overlocking is enclosed inside. If the fabric is quite ‘bouncy’ and won’t stay in position you could press the edge over once first and then roll it the second time. Whilst the result is wider than pin hemming it is narrower, and possibly quicker and more accurate, than a simple turned hem.

Stitching the hem with the overlocked edge rolled to the inside.

This last suggestion is from a project which will be blogged very soon. I cut 6cms wide bias strips which I used to create a self-neatening hem on a pair of pyjama shorts.

the bias strips were applied right side to wrong side on the shorts hems.
the bias strip is on the inside at the moment
It is then turned up to the outside where I trimmed and stitched it with ricrac braid.

I hope you’ve found my suggestions useful or thought provoking, is there something here which you’ve never encountered before, or that’s made you think how you could use a technique you already know in a different way? The idea is to show you a few ways of finishing hems, or raw edges, in new and interesting ways. I’ve not included the usual hand stitching methods because there’s nothing new to think about, although please let me know if you use these methods in a more unusual application. Just because the pattern instructions tell you to finish the hem a certain way doesn’t necessarily mean you have to do it that way…although think it through carefully just in case the really is a reason!

Until next time, Happy Sewing

Sue

Pfaff air threading and a Tesselate Tee!

There’s a lot going on in this post because I’m offering you my thoughts on not one product but three! 

So, a bit of background first…I used to be a keen runner but various injuries forced me to stop and then I never quite got started again. Fast forward at least 3 years and I’d gained weight which I wasn’t happy about, I felt sluggish and lacking in energy, I wanted to lose the weight for the good of my health and mental wellbeing. So, coming up to date, the return to running is going well (if cautiously…) and I’m losing some weight which in turn has inspired me to try making some of my own activewear. Fortunately for me Melissa Fehr of Fehrtrade has become a sewing friend of mine since first meeting her at the Sewing Weekender a few years ago and she generously offered me a copy of her Tesselate Tee pattern to try. I’d helped test her Rouleur leggings last year so I already had that pattern. Part of the beauty of Melissa’s patterns is that she gives you really comprehensive instructions to be able to sew activewear using just a regular sewing machine if you don’t own an overlocker. I’m in the fortunate position at the moment to be a Pfaff Brand Ambassador and I have their air-threading Admire Air 5000 on loan, along with a Coverlock 3.0 as well so this all seemed like the perfect opportunity to make some new running kit. 

Suitable activewear fabric is not something I have in my stash other than the scraps left from testing the Rouleur leggings so I had a little online search and came across Frumble fabrics. They have a good range of activewear fabrics at competitive prices as well as an impressive selection of suitable elastics and other trims or haberdashery you might need for this sort of project. I bought a metre of plain navy fabric and a metre of navy camouflage print, along with navy soft waistband elastic, some navy fold-over elastic and, finally, silicone grip elastic. [One point I should add here is that I decided not to pre-wash the fabric, this was based on my own knowledge and belief that synthetic fabrics are usually more colour-fast than natural fibres. I was wrong. The navy came off on my hands as I was making it up so as soon as I finished both garments they have been through the wash after all. I have alerted Frumble so I’m not saying anything here that I haven’t already fed back to them. Overall I’m pleased with the fabric quality and I learned my lesson-prewash even if you think it doesn’t need it!]

I opted to go for a medium size Tesselate top, Melissa has recently layered the pattern so now you only need to print off the size or sizes that you want, I wavered between small and medium according to my measurements. The small probably would have been fine but the medium gives me a little more room without the constant thought that I should be sucking in my wobbly bits! One of Melissa’s USP’s with her patterns is interesting seam lines which means, as well as striking designs, you can often use up small pieces or remnants of suitable fabrics. The Tesselate has a variety of options including short or long sleeves, thumb cuffs, a hood (with ponytail hole!) and back zipped pocket. 

I cut the leggings a mixture between small and medium and I’m happy with the fit of the end result. I had enough fabric for long sleeves on my Tesselate and, although there’s a pattern for the back pocket, rather than print it off I made my own. 

I opted to put the pocket in the back left diagonal seam because I decided I could reach it comfortably behind me and use the zip easily whilst moving if necessary. I drew onto the pattern how big it needed to be to accommodate the essentials.
I placed spot and cross paper over the top and traced off the shape, adding 1cm seam allowance to it.
a new pocket bag labelled and ready

I played around with the fabrics until I was happy with their placement, I had enough of the blue spotty fabric for the back and front side panels, everything else I divided between the two navy fabrics.

Because I was going to be sewing a fair bit of the garments together directly with the overlocker I join the pieces with the pins at least 2-3cms away from, and parallel to, the cut edge. Then it’s safe to sew without the pins being anywhere near the blade.

I’ve made another little video to demonstrate how the air threading works on the Pfaff, you’ll need to bear in mind that it might seem like it takes a while to thread and so where is the advantage in air threading but that’s because I’m trying to explain as I go and I was sitting at a funny angle behind the camera whilst I did it.

After two years of owning the Quilt Ambition 2.0 (now discontinued) I’m used to the quality of Pfaff machines so it doesn’t surprise me that the Air Admire is sturdy (no shifting about on the table while you sew) and very speedy, with a superb quality of stitch. It doesn’t take long to get to grips with the air threading and, as I mention in the video, there’s an automatic threader for both needles too! I couldn’t get the hang of that at all to start with but it’s amazing what a difference it makes if you read the instructions and follow them! Of course, this is an expensive machine and I understand that not everyone will have that kind of budget but if you are considering an air threading overlocker (there are now a lot more models on the market than just market-leader Babylock with prices gradually coming down) then this one is most definitely worth thinking about.

I inserted the invisible zip on the sewing machine, then attached the pocket bag that way too. The T-shirt goes together pretty quickly considering the number of pieces-most pieces are cut singly because they are asymmetric-if you’re using the same fabric throughout it would be an idea to label your pieces in some way so you don’t get them mixed up.

I find it very useful having a variety of stitches to choose from especially when sewing with stretch fabrics, the 3-step zig zag was ideal when I was sewing the elastic into the waistband, I also have an ‘elastic’ stitch which is useful. A lot of machines, even quite simple ones, will probably have a stitch option which will enable you to sew activewear so why not try out a few of them to see exactly what they are, the instruction book should be helpful, or there’s so much information on the internet too.

The finished waistband on the leggings, elastic is completely enclosed in a seam at the top and then I’ve secured it further with a 3-step zig zag stitch
I’ve joined the elastic for the legs into loops which are then sewn to the right side of the fabric, matching the edge of the elastic to the cut edge of the fabric.
I used a small zig zag to stitch it in place. This then flips to the inside and I coverstitched it along the top edge.

To neaten the hems and around the neck I swapped over to the Coverlock 3.0 which I had on the coverstitch setting. Again, this is a very sturdy piece of kit with excellent stitch quality, I am finding there is a certain knack to using it and I’m by no means an expert yet but it certainly gives a very professional finish to knit, jersey or stretch garments.

The Rouleur leggings also have large side pockets which are perfect for holding your phone and/or keys etc (Betsy getting in on the act again too)

As always, I hope you’ve found this helpful, I always try to be honest about how I get on with a product whether or not I’ve been gifted, loaned or purchased it-all three in this case. If you’re tempted to have a go at activewear then Melissa is a good place to start-she’s even written a book on the subject so you’re in good hands!

Until next time, happy sewing

Sue

Dawson Coatigan by Thrifty Stitcher

I followed the progress of this pattern with interest on Instagram when it was originally released nearly two years, it was fascinating to see how Claire-Louise Hardie (the Thrifty Stitcher!) developed and finessed the various elements of it as she sampled it, up to the point that she was ready to release it for sale. It has attractive style lines with princess seams in the front which curve into hip pockets, the back also has princess seams and there’s a horizontal seam just below the natural waist. The collar curves up smoothly against the neck and the back collar has a ‘sunray’ of five darts spreading out towards the shoulder blades which I particularly like. The cuffs each have 3 similar darts, the details on this pattern has simple but so stylish.

My copy is a paper pattern but it’s now a PDF available from CL’s own website.

This post was originally published last year by Minerva who generously provided me with a nice firm Ponte Roma in a plain navy to make the Dawson in, it would also work very well in a boiled wool, felted wool, Melton, not a loose tweed though as they can start to fray and you’d lose the details too much in the weave. Anything fairly structured and stable would effectively show off the style lines. You could get some interesting effects with checks or stripes if you want a challenge! I’d wanted to make another version for a while because I’ve had really good use from the navy one, I hadn’t got around to finding any specific fabric for it but then I hit upon the idea of using a single old heavyweight cotton curtain that used to keep the drafts out by our front door. It had long been replaced for this task but I just had it folded up underneath the heat-reflective mat that I use on my cutting table. In order to maximise the fabric in the curtain I undid the deep hem and the sides, and removed the tabs at the top. I gave it a wash to clean it but also to, hopefully, stop it shrinking later on.

Areas like the pocket edges and the neck need stabilising with some iron-on tape or strips of interfacing as per the instructions, especially if you use a knit fabric like Ponte. I would recommend stabilising the shoulders with seam tape or scraps of ribbon to prevent stretching too. I used a specific needle for stretch fabrics and you could use the ‘lightening’ stitch to sew with if your machine has it, or a very straightened out zigzag. If you do use boiled wool the layers could be quite thick, use a straight stitch but you may need to lengthen it a little more than usual.

The pattern comes in eight sizes which are not numbered in the conventional way, CL opts for letters instead, so you work from your own body measurements to choose which size should fit you. I cut and sewed a size F originally which was quite generous, for the newer version I’ve cut the next size down. I misjudged how generous the ease is in the garment so I usually wear the Ponte version layered up over jumpers or sweaters on warmer cool days if that makes sense. At the end of the day it’s intended as a casual coat so don’t make it too small as you’ll always be pulling it closed across you. The sleeves are nice and roomy too, I’ve noticed some coat/jacket patterns can be a bit snug around the bicep for me which is a bit dispiriting, I’m hardly a muscle-bound hulk! Just check before cutting out if you’re happy with the sleeve length too, I probably could have added just 3-4cms because it feels the tiniest bit short on me.

The pattern goes together beautifully and all that tweaking in the sampling stage is borne out in the final version. I found the instructions pretty clear, they are mostly photographs and there are some really useful hints and tips which will come in very handy if you aren’t that experienced in your dressmaking yet. Make sure you transfer your markings for the pocket pivot point for example so that you get a crisp finish for the corners.

You could top stitch all the darts down, possibly in a contrast thread if you like, but because the Ponte had a slight stretch I didn’t do this on mine. I did top stitch down the front facings though and caught them down in a couple of places on the inside to stop them flapping. 

For the ochre version I topstitched more of the seams, I confess that I was incredibly slovenly and used up various threads in my collection so not all the stitching is the same colour…oops! Incidentally I didn’t use top stitch thread, instead I used the triple straight stitch which looks very similar although it is quite thread-hungry (hence the non-matching!)

This time however I didn’t top stitch the front facings down, I adopted a different approach. As it’s an unlined coat so all the innards are visible I used some ribbon to anchor the facing down in a couple of places. I chose to do this because I know from experience that when you’re sewing through several thick layers the triple stitch (which is a set length on my Pfaff and not adjustable) it can lead to puckering which doesn’t look so nice. Try a sample before you go ahead if you aren’t sure, that’s a LOT of slow unpicking if you don’t like it after all.

ribbon tabs between the facing and the pocket bag stop the facing from flapping about too much
You can see from this shot where I’ve placed the ribbon anchors.

I finished the hem by hand using a herringbone stitch rather than machining it for the same reason that I didn’t top stitch the front facings.

I think the Dawson is a well-drafted and executed pattern from an independent designer (and CL’s art work features herself so it squeaks into the #so50visible category!) The Minerva Ponte Roma works well for the soft tailoring, using my old curtain gives the slightly cocoon-shape a little more definition. It shouldn’t be too difficult to do an FBA if you need to either. I’m much happier with the fit of the ochre one, but I love the navy and will still wear it regularly too.

cheer up love!

Because the Dawson is a loose cocoon shape it would make a beautiful evening coat in a glamorous brocade, to go over the top of your evening outfit, denim would look great too (Have a look at my Simple Sew Cocoon jacket in denim here)

I guess this was also a useful exercise in upcycling, the curtain was years old and not being used for it’s original purpose so I thought why not give this a try. If I found I wasn’t mad about wearing the colour after all I know it’s 100% cotton so it would dye, I might come unstuck with the polyester sewing thread though which would take up the colour differently-it’s hardly Saville Row standard though! The Dawson took barely two metres of fabric (the front facing is helpfully cut in two parts which helps reduce the fabric usage, and of course you could always use a contrast fabric anyway) it doesn’t instruct you to use interfacing on any of the collar or facing parts but I did, just to stabilise the fabric a bit.

Until next time, Happy sewing

Sue

A Simple Sew Cocoon dress hack

I had made two Simple Sew Cocoon dresses without alteration when the pattern was first released a couple of years back, and you probably know that I love a bit of a pattern hack so I decided that the style would be good for an adaptation. I’d drawn a few sketches of ideas and had a rummage in the stash for some suitable fabric when a funny thing happened…

I found I had already cut out a hacked Cocoon in the past!! I realised I must have done it easily two summers ago but then abandoned it because I decided it would be too short. I remember it was a limited amount of fabric, probably 2 metres, but I put it to one side and forgot about it. 

Fast forward to now, I wanted to make it up but I needed to lengthen it in a way I was happy with. I had truncated the bodice at Empire line just below the bust and then the skirt was two widths of the fabric, a simple dirndl. I’d cut the facings too but there was literally nothing else left except small scraps.

There’s a centre front seam in the bodice, I cut the dress horizontally under the bust at about Empire line

I went through various options including adding extra frill layers but to do that you gradually increase the amount of fullness needed for each layer, in other words, layer 1 would be 1.5x the waist measurement, layer 2 could be 2x the length of layer 1, and layer 3 could be 3x the length of layer 2. In simple terms this means longer and longer strips of fabric are needed to form each frill to be sewn to the previous one, and the longer the length of the dress the more layers you might need. Basically I couldn’t make the skirt any longer with what I had because it was already cut, and because of the lockdown I couldn’t go out to look for a suitable plain cotton. I returned to the stash and eventually found 50cms of cotton poplin which I know I bought at the same time as the original, I must have intended it as a contrast but never used it.

By cutting the 50cms piece across the width into two 25cms pieces I could join them at the side seams to form a loop and then fold them in half to create a 12.5cms deep band which I would sew to the hem of the dress! Simple! 

Once I’d worked all this out I sewed up the bodice, rather than hemming the cap sleeves I used some binding from my stash so that I could maximise their length. I planned to twin needle some top stitching in various places and I used two different coordinating threads for this. 

Bias binding sewn onto the sleeve then understitched
bias binding turned back
The completed sleeve with twin needle topstitching

I did the same around the V neck once the facing was sewn on, in order to get a pristine join at the point I carefully unpicked a couple of stitches and secured them on the reverse.  

I wanted side seam pockets (of course) so I had to cut them out of some plain cotton scraps, each piece was added to the side seam and then the side seams sewn up. 

The new band was initially slightly wider than the lower edge of the skirt so I restitched it until the two were the same width and matched exactly at both side seams. I used the overlocker with four threads to join and neaten the band in one step, I pressed the seam upwards and then twin-needle topstitched it to decorate. 

the band folded and pinned to the lower edge of the skirt

The final step was to run two rows of gathering stitches at the top of the skirt then sew it onto the bottom of the bodice, matching at the side seams. I pressed this upwards too and topstitched it as well.

For a dress which had languished with not much hope for two years I’m really happy with it!! I loved the fabric (which was from John Lewis originally I think about 4-5 years ago!) and I was so cross I’d cut something which I couldn’t imagine I’d wear if I sewed it up. By adding the deep band the skirt now has weight as well as length. It’s been so comfortable in the hot weather, why did I wait so long?!

we were heading out for our exercise hence the unsexy shoes!
we have a Henry Moore sculpture on loan for the duration of the centenary year of our town, maybe we can keep it for an extra year now that all the summer celebrations are cancelled?
Coronation Fountain
yes I have got water coming out of the top of my head!

Lockdown is easing in the UK since I originally finished this dress but I hope, as always, this hack has given you an idea of how simple it can be to take a section of a pattern you already have and give it a twist to become a different garment. I had very limited fabric with a print which still needed to match everywhere, by adding the hem band I’ve given it the look I was after…it just took a couple of years to think of it!

Until next time, happy sewing,

Sue

Two Minerva makes in one go!

I originally wrote this as a review for the MinervaDotCom blog but I’m not actually sure if it ever appeared. Rather than waste my efforts I thought I’d publish what I wrote here instead.

I’m sure it was a combination of an over-generous stated fabric requirement, my just-to-be-on-the-safe-side ordering and then super-stingy cutting out means that I managed to get not one but TWO sweatshirts out of my Minerva fabric choice this time. At the time of writing last autumn, Minerva were introducing a collection of textured jerseys made in a polyester/ viscose/ spandex mixture which came in a wide range of colours and textures so I opted for a geometric design in lilac to try out. I would suggest that this fabric is not as firm or thick as some jerseys suitable for sweatshirts, it isn’t fleecy on the reverse for example but it has reasonable drape, is soft to the touch and has a fair amount of stretch but not in a ‘really difficult to control’ kind-of way (it isn’t like lightweight jersey for T-shirts for example) it’s actually pretty stable so manipulates well into armholes or cuffs. 

I already had a pattern I wanted to try, the Maxine sweatshirt by Dhurata Davies that has interesting diagonal seams across the front which have pockets in them. This actually made cutting out a whole lot more tricky than I anticipated because the ‘check’ design of the fabric I had picked turned out not to be square but rectangular so matching the lines was a real challenge. In some areas I’ve failed so my advice would be “don’t choose a pattern that has too many intersecting seams or style lines” because you could end up tearing your hair out when you can’t get it to match! Once I’d committed though I decided to press ahead and settle for ‘almost but not quite’…not my usual route but there we are.

When it became apparent that by folding and cutting really carefully I’d have oodles of fabric left over I pulled out a very simple sweatshirt pattern Simplicity 8529 and cut that at the same time. You might recognise this pattern as the Toaster sweater by SewHouseSeven if you think it looks familiar. If you fold the selvedges in towards the centre so that you have two folds then it’s often possible to get more pieces out of less fabric, any sleeves, yokes or facings can be cut out of what remains.

I currently have a Pfaff Coverlock 3 on loan to me so I used it to sew up much of the two tops on it’s 4-thread overlocker setting but you can easily sew this fabric on a regular machine, just use a ballpoint or stretch needle and set your machine to a very elongated zigzag if you can (regular stitch length and a narrow width) or a ‘lightening’ stitch if your machine has it. Unlike some jerseys or sweatshirting you’ll definitely need to neaten the seams though because I found the fabric frayed and went fluffy at the cut edges quite badly as a result of the woven nature of the surface design. Use a zigzag stitch on the edges if you have limited options, or pinking shears. 

the cut edges fray like this a little bit.
the Pfaff Coverlock 3.0, it’s been a fantastic machine and the quality and versatility of its stitching has been superb.

The ‘Maxine’ is a great design which stands out in a crowded field of many other sweatshirts and the well-written instructions and diagrams are very clear and simple to follow. The tricky area could be the point at the centre where the seams intersect, I simply made this more complicated for myself by choosing the geometric design! And of course it has pockets! I’ve made another version of it since the lilac from a remnant of linen/wool which you can read about here.

Maxine sweater in linen/wool mix from Merchant and Mills
this is a slightly truer version of the colour

The Simplicity/Sew House Seven pattern has a very simple ‘grown-on’ collar and self bands on the cuffs and hem. I cut and made this one up in less than two hours and it shows off the textured surface of the fabric very well. 

Simplicity 8529 with cuffs and hem band finish, I like this top so I think I’ll make another next winter but do the longer straight version.
You’ll notice that neither top is long but I’m happier to be able to make two shorter but perfectly wearable tops rather than one longer one with fabric left over which wasn’t enough to use for anything else.

I would suggest that this fabric will make very comfortable loungewear like track pants, tees, sweatshirts, dresses and children’s wear. I don’t know what the other designs in the range are like but if you are pattern match averse then this particular one might not be for you! I thought at the time it would be interesting to see how well a fabric with a raised surface texture like this wears and now that several months have elapsed I’ve found that it catches quite often and has started to pill quite significantly which is disappointing given the price per metre.

My thanks to Minerva for providing me with the fabric to write about, this is a significantly different version of the blog post which may, or may not, have appeared on their website. I did try to find it but their search function doesn’t make it very easy to find specific posts.

Until next time,

Happy Sewing,

Sue