The Sewing Revival Heron dress hack

Two years ago I wrote a review of the Sewing Revival Heron dress which you can still read here. I liked the pattern so much that since then I’ve made another knee-length version in a viscose/linen mix fabric from Ditto in Brighton and a blouse variation too in a beautiful soft Italian cotton voile, also from Ditto. I wore it often although not so much lately…

wearing the blouse on my trip to Paris for the Sewcial in May 2019
my very first version of the Heron dress…it has pockets!

While I was at Sew Brum in October 2019 I bought some lovely soft brushed printed viscose twill from Barry’s Fabrics with the express intention of making another Heron but this time making it longer and more cold weather-friendly. There had been a lot of Wilder Gowns by the Friday Pattern Company popping up everywhere at the time, I liked the tiered style a lot but I knew I could create my own take on it by using a pattern I already had. A multiple-layered skirt like this isn’t difficult, it’s really a case of working out the number and sizes of rectangles you want to use. If you take a look at this post I wrote about recreating a sun dress for a client in 2019 you’ll get the gist. Because I like the top section of the Heron so much I decided this was a good pattern to use and it wouldn’t be difficult to adapt it to what I wanted.

All the quantities and proportions I have used for this dress were completely arbitrary and had to be based primarily on the quantity of fabric I’d purchased [which I can’t actually remember as it’s well over a year ago, probably 3m of 150cm wide fabric I’d guess] and my own height of 5’5” so bear this in mind if you decide to have a go yourself. I wanted the dress to be nice and long so eventually I settled on approximately hip length for the bodice, the finished length of the side seam is now 40cms. I folded the front and back dress pattern sections up out of the way when I pinned them to the fabric (obviously you could trace or print off a new copy of the PDF if you wish) Once both bodices, sleeve and pocket pieces are on the fabric [pockets could be cut from something else if you’re a bit short of fabric] I could see exactly how much I had left to create the skirt from. I kept it very simple and divided the remaining fabric into two equal rectangles across the full width, each one measured approximately 56cms long but that had to include the seam allowance at the top and a hem at the bottom.

Initially the construction of the dress followed the normal method up as far as putting the pockets into the side seams of the bodice as per the pattern.

Making the skirt was very straightforward, I joined the short selvedges to one another [if it’s a one-way design make sure the print is running the same way on both pieces] to form a large cylinder of fabric with two side seams. Press the side seams open, if you’ve been able to use the original selvedges they might not need finishing. I made the hem at this point too, it seemed easier than wrestling with a complete dress at the end, although this could have backfired on me if I hadn’t been happy with the length but I was pretty certain it would be OK.

I ran two rows of gathering stitches within the seam allowance of the top edge, I pinned them in position matching the side seams, centre front and centre back, plus the quarter seam positions too. Gather up carefully so as not to break the threads, small pleats would also work here especially if the fabric would be bulky otherwise, it depends a bit on the weight of the fabric to some extent. Once I was happy with the gathering distribution I sewed the skirt on and overlocked the seam.

And that was it. Now, I have to say that because I was taking a risk with proportions and limited by the quantity of fabric I’d bought that if I were to repeat this I would definitely make the bodice quite a lot shorter and make the skirt from more than one gathered tier instead. I’m happy with the overall finished length but I think the seam at the hip isn’t quite right. But, by wearing it with a narrow leather belt (there wasn’t any fabric left for a self-belt anyway) and bringing it in at the waist I’ve saved it, the belt gives it a lot more definition.

I added a tie at the neck this time using a bit of grosgrain ribbon which I had knocking about.

I grabbed a cheeky selfie in John Lewis with my sewing friend Ruth in the autumn, we can only dream of when we can meet up again at the moment though sadly. that’s my upcycled jeans jacket I’m wearing

The dress was finished around a year ago and these photos were shot in the autumn but it’s taken until now to write up. I just wanted to demonstrate how easy it can be to make your own version of popular patterns using one you already have-there’s a certain risk involved because it might not be completely successful but that’s always the risk anyway when making our own clothes-a style might turn out not to suit us after all, or we make a wrong fabric choice, or it could be a triumph so why not revisit what you already own before buying another pattern?

Until next time, happy sewing

Sue

2020-Sewing in a Time of Pandemic

Well what a year 2020 turned out to be!

It’s been such a tough time for so many and being a part of the wider sewing community has been a very real lifeline for many people. Those of us that enjoy making our own clothes already realise the obvious benefits this can give us; total freedom to choose types, colours and patterns of fabrics as we wish, the ability to emulate high-end or high street fashion at the price-point we can afford and the skill to make clothes fit our own particular body type, to name but a few. It shouldn’t then come as a surprise that the wider world, whilst searching for activities to entertain and occupy them during the long weeks and months of lockdown, discovered (or rediscovered) that home sewing can be creative, absorbing and rewarding which is a VERY GOOD THING! Who knew there was a link between doing a creative activity and a more balanced sense of well-being??

To be honest it doesn’t matter what that activity is, or whether you’re really any good at it, the fact that it can take your mind away to other less stressful places for a time is what matters.

But at the start of the year none of that was of much interest to most. I was extremely fortunate in January to go on a cruise to the Caribbean so I made a couple of new things to fills ‘gaps’ but mostly I took old favourites…cue multiple photos of 3 versions of The Maker’s Atelier Holiday shirt on heavy rotation! One new item was the Trend Square dress I made in fabric given to me by Dibs from Selvedges and Bolts the previous year, I got a lot more wear later on in the summer.

Within a couple of weeks of getting back, Judith Staley and I hosted the very first Sew Over 50 meet-up in London. We very much hoped, and expected, that it would be the start of many more such meet-ups between followers of the @SewOver50 account all over the world but it wasn’t to be…not yet anyway.

If you’ve been reading my blogs for a while you’ll know that as well as meeting up for sewcials with fellow sewers I really enjoy my visits to exhibitions and galleries. At the end of February I caught up with Janet Poole who is a fellow Lamazi blogger at the Stitch Festival in London, I had such a lovely day shopping and chatting with her, and her friend Great British Sewing Bee winner Juliet too. We didn’t realise it then but we were very fortunate to be able to attend the event at all and I wouldn’t be surprised if others who went didn’t catch the-virus-that-shall-not-be-named because it was so crowded.

About a week after this I was able to go to the stunning new Kimono show at the V&A and, although we didn’t know it at the time, that was to be the final outing for several months…

I wore the new Homer & Howells Cissy dress (and failed to remove my coat from shot which I chucked on the floor!)

So then we entered the first long lockdown and that’s when sewing (and some baking) became my primary occupation. During this time I had some blogging commitments for Simple Sew Patterns and Lamazi fabrics to complete. For my first Lamazi post I made a Trend patterns Bias T-shirt dress which was a tough make, not because the pattern was difficult but because I was making the dress for a wedding that never took place. And worse than that, I was making the Bride’s gown too so I still have an almost-finished dress waiting for the day that the wedding can happen.

In all honesty I hated how I looked in this dress because I had piled on weight and felt very self-conscious in a fitted dress. It was a lovely pattern made in beautiful fabric but I felt I was doing both a disservice. Eventually I did wear it in September by which time I had lost weight and it was a delight to wear! I’m sure I’m not the only one whose state of mind has fluctuated wildly this year and my self-confidence was rockbottom when this picture was taken.

I know I’m very blessed in that I have little to actually complain about in my life but that does not mean that these months of lockdown didn’t take their toll mentally so, when the call to help make scrubs came, it was something I could actually do! Eventually I made 10 sets, I believe they were headed to a maternity department in a London hospital.

I continued to keep busy by doing a few refashioning projects because the desire to make new things that weren’t going to be worn outside the house was just too depressing. I love the act of making clothes, the planning, the cutting out, the sewing, because that was taking my mind off what was happening in the real world but how could I justify making new clothes that I had little use for? Even dressmaking was starting to become a negative because I felt guilty about it. By doing some refashioning projects using things I already had, other than new fabric, I made a few items including pyjamas for my final Simple Sew post and another pair using the PJ pattern in the Great British Sewing Bee book written by Alex and Caroline of Selkie patterns and for which I had made a couple of samples. I used 4 old work shirts of my husband’s which were very well worn! I also made (eventually) two pouffes as well which took care of loads of scraps and off-cut furnishing fabrics and were extremely satisfying! I also refashioned a very old and redundant heavyweight cotton curtain into a Dawson coatigan by Thrifty Stitcher.

Early on in lockdown I had the pleasure of talking to Maria Theoharous for her Sew Organised Style podcast on a couple of occasions. I’ve set up a separate page so you can access this to be able to listen to her inspiring SewOver50 guests every week. One of our chats revolved around how we each arrive at our fabric choices for specific purposes or projects, I wrote this topic up as a post which you can read here, and I also wrote a further post which came from when I was guest editor on the @SewOver50 account and we talked about our cutting out processes-did we cut and make one thing at a time, or cut several things and have multiple projects on the go? Scissors or rotary cutter? Pins or weights? It was wide ranging and fascinating with so many excellent ideas and practices. I hosted another discussion about a variety of hem finishes later in the year and you can read that one here. Incidentally, by the end of this year @SewOver50 has reached an incredible 25,600 followers!!

One of my stranger tasks this year was to carry out a socially-distanced dress fitting on a doorstep! Before lockdown started I had been commissioned to make a dress for a work colleague of my daughter Katie. Thankfully I’d opted to make a toile of the bodice which I’d fitted just before lockdown kicked off so I managed to get the dress to a good stage of completion. However, I got to a point where I definitely needed her to try it on because even if she couldn’t wear it for the event she had hoped to, it would be nice for her to take delivery and wear it around the house!! So I went to their place of work and handed the dress over at arms length to Tracey to put on in the staff toilet, then she came out onto the porch where Katie, under my direction, pinned the dress for me. I took a few photos for reference too. From that I was able to finish and deliver the dress and my client was delighted with it…phew

One of the regular sewing highlights of the last 4 years for me has been the Sewing Weekender which generally takes place in Cambridge, UK in August. The organisers took the bold decision to put the whole event online instead which meant that many more people could ‘attend’ from all over the world. Myself and Judith Staley were delighted to be asked to contribute a video message each which was very nerve-racking but it turned out alright in the end. I published a transcript of mine here, along with the original video (you’ll notice that I had abandoned my signature pink hair by this time because, quite frankly, what was the point of bothering!) The Online Weekender also raised a significant amount of money which was divided between 4 charities. 

As lockdown started to ease in the summer I was able to get out and about a couple of times. I joined an al fresco rag-rugging workshop in Hertfordshire run by Elspeth Jackson of Ragged Life which was so enjoyable, and I visited a couple of exhibitions in London including the Kimono show again, plus Andy Warhol at Tate Modern and Tricia Guild at the Fashion and Textiles museum both on the same day. Since then though things have been shut down then reopened, then shut down again. My heart goes out to everyone who is trying to run a business or an organisation that relies on visitors through their doors to make them viable, their future is very uncertain.

I’ve made a few other garments during the autumn which I’ve been really pleased with including the Prada-inspired shirt dress and a pair of Utility pants by Trend Patterns (not blogged yet) but I feel I’ve run out of steam with my sewing right now and I never thought I’d say that. My own teaching classes restarted for a total of 5 weeks in October but they’ve stopped again. I know some have adapted by using Zoom or other platforms but it just wouldn’t work for me, I feel dressmaking is too hands-on and needs real assistance for tricky bits, holding things up to the camera isn’t good enough sometimes. And being part of a group and all that shared enjoyment is a huge part of it too. I’ve had fairly regular online catch-ups with some of my lovely sewing friends and that has been a joy, albeit not as good as seeing them in the flesh.

Mr Y was the lucky recipient of a few handmade garments too during 2020 when I made him another two Kwik Sew 3422 shirts, and not one but two Thread Theory Finlayson sweatshirts! I’m happy to say he’s delighted with all of them and I’ve got plans for another sweatshirt for him in the new year.

I’m working on my own pattern which I’ve self-drafted so hopefully that will be something positive for the new year but I need occasional assistance from more expert friends and that’s making it a drawn-out process which would have been so much more fun person-to-person.

One final project I was commissioned by a friend to make was a Christmas chasuble for her to wear as she presides over her Christmas services in church. A chasuble is essentially a fancy poncho which the priest wears over their other vestments and Wendy wanted me to create one with a Nativity scene on it. She sourced the base fabric with my advice, and a printed quilting cotton Nativity which was sent from the US. This was square so I carefully cut it into approximate thirds with the central third featuring the stable scene and the star for the front, another third with Bethlehem for the back and the remaining third I cut into two parts to use on the stole, which is the long scarf priests wear around their necks. All of these I attached by appliquéing around the black outlines (I was literally making it up as I went along!) Wendy is delighted with the finished result (thankfully) and I’m sure she will enjoy using them during the Christmas season.

As I finish writing this (2 days before Christmas) we have no idea what lies ahead…some countries seem to be slowly recovering whilst the UK as a whole seems to be sliding further and further into disaster, or maybe not? I should try to think more positively as scientists have worked tirelessly to make a vaccine which will gradually be rolled out. Personally I’m a long way down the list for it but that’s absolutely fine, we must protect the most vulnerable first.

I’m making an effort to look cheerful in this most recent Lamazi blog make, but the wine was slightly off watered down Rosé from my daughter’s fridge and it was 10.30 in the morning! I’m genuinely pleased with the dress though and in spite of everything I’ll wear it on Christmas Day because there’s plenty of room for expansion!!

This has probably ended up not being a-not-entirely-coherent post but that’s kind-of appropriate I reckon! Wherever you are and whatever the new year brings for all of us I’d like to thank so many of you for reading my posts, sending me lovely or encouraging messages. Being a part of the online sewing community and Sew Over 50 in particular has been an absolute joy and a lifeline at times. We need to lift each other up more often, call out injustices when we see them but not to the extent that it becomes bullying of individuals, that isn’t right either. 2020 has been a year of huge upheaval, I plan to restart 2021 with fresh sewing plans to help me to feel more positive about it…it’s going to be a bumpy ride!

Until next time, stay safe!

Sue

a multitasking Festive outfit

The Festive season is often a reason to make, or buy, a special new outfit to wear for office parties or Christmas Day but this year’s Festive season things will be very different for most of us. I don’t want to be entirely negative though so, as part of the Lamazi blogger team, I thought I’d make something which is a little bit Christmassy but will double up as a ‘regular’ winter dress too. 

I’ve chosen the cord velvet from Danish Design in a gorgeous shade of aubergine-I’m always a sucker for purple-but it comes in several other beautiful rich shades including a sumptuous gold and a stunning teal too. I picked this fabric because it’s a medium weight stretch jersey and has soft pile which makes it lovely to the touch. I’ve made a dress but you could easily make tops or wide-legged pants in it, or babies and children’s clothes too because it’s washable and crease resistant. 

Whilst I love a complex make to really get my teeth into I felt this wasn’t a garment which warranted lots of time. Making a special Christmas once-worn garment wasn’t appropriate any longer so I wanted something quite simple but adaptable and for that reason I’ve picked the Somerset T-shirt by Maven Patterns. I’ve made a few of these now, the bones of it are beautifully simple, it has a self-neatened bateau neckline, a slightly fitted silhouette and four sleeve options. I’ve chosen the Bishop sleeve with a long cuff but I’ve hacked the sleeve to make it even fuller, and I’ll lengthen the body to create a dress finishing below the knee.

Another idea was to add a flared skirt which looks nice but didn’t think I would use it as much as the straight version.

The Somerset has excellent very full instructions with lots of tips and advice to get a good finish. There’s a useful sheet to write all your information including body measurements and fit alterations, and a fabric stretch gauge to check you have enough stretch for the pattern to fit properly. You can also list the needle type and size you’ve used, stitch type and length and anything else you might want to remember for another time. 

To increase the size of the sleeves I took the bishop sleeve pattern and drew 5 vertical lines from each of the notches from shoulder to hem. Each segment will become slightly wider as it gets nearer the bottom edge so make sure they are even in size.

Cut a piece of spot and cross or tracing paper bigger than the pattern as it is, mark a grainline running right down the paper and then lay the pattern piece on top of it, matching the grain on the pattern to the grain line you’ve just drawn. Next, I carefully cut up to the top of the marked lines taking care not to snip right through at the top, keep it attached by a tiny amount to act as a pivot point. [If you don’t want to cut your original pattern piece I suggest you trace off a new one to use instead] Then you splay the hem edge apart by a few centimetres each, I added 2.5cms between the each of the ‘side’ segments and 5cms to the central one. By doing this you’re adding fullness at the hem but not altering the sleeve head. You could put additional fullness to the sleeve head by opening the top edge too if you wanted. I lengthened the sleeve by 5cms too so that it would have plenty of blousy fullness into the cuff. 

Trace around the new shape using a tracing wheel or pencil and cut out the new piece transferring all markings. One final change I made was to add a bias grainline because I knew I wanted to play with the stripe direction of the rib on the fabric.

I had pre-washed my fabric and partly tumble dried it on ‘low’ before letting it dry completely on the clothes airer, it seemed to survive the experience just fine. 

I made an arbitrary choice of how long to make the dress by simply holding the tape measure at my shoulder and seeing where it came to at about mid-shin! I attached another piece of spot and cross to the bottom of the front and back pattern pieces and drew on the skirt length I wanted, plus a generous hem. I knew I would have to make some adjustments to the hip and thigh during the fitting stage, just make sure that the hip and thigh measurements are plenty big enough because you can always remove some, it’s much harder to add later! 

The ‘cord’ runs across the width of the fabric and I wanted the rib to run down the length of my dress which meant I had to fold the fabric across the width. Try not to twist the fabric if you have to fold this way, I marked a single rib by following it across the width with pins so that I can see it clearly. Fabrics like corduroy, velvet or velour have a pile or ‘nap’ which will shade so if you cut some pieces facing one way on the grain and some pieces running the other way then you will end up with a garment that looks like it’s been made with two different colour fabrics, even though you know that isn’t the case. If you’re unsure what quantity of this type of fabric to buy go with the ‘with nap’ amount on the pattern information and follow the one-way layplan to cut out.

I marked the rib across the fabric with pins so that I could be sure it was folded correctly and would not be twisted.

Once I’d cut all my pieces I followed the making instructions which are very comprehensive. If you have a walking foot for your machine I strongly recommend you use it because velour like this has a ‘pile’ and has a tendency to ‘creep’ as you sew so you might find that it starts off with all the edges matching but by the time you get to the other end the two fabrics are no longer matching. I also strongly recommend you tack any seams you are unsure about. You could use a million pins but by the time you’ve done all that you could have basted it in place which does the same job and usually more effectively. I was able to coverstitch the neck and the skirt hem on the Pfaff Coverlock 3.0 I have on loan as a brand ambassador but it works just as well by overlocking the raw edges and twin-needle stitching them down, or zigzag and twin-needle, or two rows sewn singly if you don’t have a twin needle. When it comes to pressing a fabric like this, if you don’t have a special needle board (and few of us do) then you should press on the reverse at all times. You could place a towel on your pressing surface and lay the fabric on top so that the pile of the cloth is against the pile of the towel which will help protect it. Use a pressing cloth as well. These tips will also apply to regular corduroy or any non-stretch fabrics with a pile too.

The bell of the sleeve is gathered using shirring elastic which helps to retain some of the stretch required for the cuff. 

Once the sleeves were in I sewed up one side seam directly on the overlocker and then pinned the other side seam to fit myself. This was because I didn’t know if I’d need a split at the hem to be able to walk in the dress and I didn’t want to end up with loads of unpicking!

First I tried it right side out to get an idea of how it was fitting initially, then I turned it inside out to pin.

I looked at the fit in the mirror first of all and the sewn side seam was quite wavy, this could be cured by either adjusting the differential feed on the overlocker so that it doesn’t happen, or you could stitch the seam on the sewing machine and then overlock the edges [This is what I opted to do because I could see I had to take a fair bit off the side seams anyway to achieve a fit I was happy with] Then I put the dress on inside out in front of the mirror and pinned out the excess. I turned it right side out and tried it on again to check the fit, then finally sewed both side seams on the sewing machine, I used a ‘stretch’ needle, a ballpoint or jersey needle performs the same task. Either use a short straight stitch or a straightened out zigzag, make some samples to see which works best for your particular fabric. 

Now I tried it on the dress inside out to adjust the seams
I pinned out a fair bit of the side seams to give more shape through the waist and hips.
still Inside out
Finally I put the pinned dress back on the right way around to check I was happy with the fit before making the adjustments.

Lastly, the cuffs go on and the skirt is hemmed. 

And that’s pretty much it, it pops straight over the head so no tricky closures, because of the stretch it didn’t need a split, and that means there’s room for Christmas lunch and it won’t look like a dish rag after spending the afternoon curled up on the sofa watching Christmas telly!

cheers!
I’ve dressed it down with an ancient knitted gilet plus a wide belt, long boots and my much loved Alexander McQueen scarf
I love a scarf to keep my neck warm!
It could be the strangest of Christmases but let’s raise a glass to a much better 2021

I have to say that I’m really happy with this dress because it ticks all the boxes I wanted it to. It’s comfortable but it looks Christmassy, it looks great with opaque tights, heels and jewellery, but also with boots, a chunky belt, a roll neck top underneath for extra warmth or a cosy scarf…and did I mention it’s comfortable! #secretpyjamas It also has the advantage of rolling up and going in the corner of a bag or suitcase and coming back out again not needing a press. Bonus!!

If you have a favourite T-shirt pattern you could try lengthening it into a dress, Tilly and the Buttons Tabitha from Make it Simple does that. You could browse the SewOver50 post I wrote listing loads of go-to T-shirt patterns for inspiration, or maybe copy a RTW one you already have?

At 160cms the fabric is very wide so a little will go a long way, and because it’s so soft it would be lovely for children’s wear too. It needs a little bit of careful handling but a lot of that is in the ground work. Make sure you lay it up and cut it accurately to minimise unnecessary stretching or distortion (try to keep it flat on the table or lay it up on the floor) pin or tack the seams so they don’t move about and press carefully as you go and you should be fine. 

It’s been an incredibly tough year for so many and I wouldn’t blame you for not feeling like making anything new to wear. However, if crafting and creating bring you joy and respite then you could view it as a gift to yourself, and when you choose to buy from small companies like Lamazi and Maven then you are helping them too.

Thank you to Lamazi for providing me with the fabric for me to write my review, and I hope you find it helpful. 

Until next time, Happy sewing

Sue

Prada-inspired shirt dress

This whole project all came about because I couldn’t resist some ex-Prada fabric I spotted on my friend Dibs’s website, Selvedge and Bolts! She specialises in sourcing gorgeous quality high-end and ex-designer fabrics from Italy and France. This one caught my eye because funnily enough it doesn’t scream ‘designer’ but I liked the graphic print which stands out amongst so many florals.

I ordered 2 metres although I didn’t have a plan for it, then it occurred to me that I should look at actual Prada designs to see if there were any that were at all wearable by someone like me (ie. not six feet tall or looking about 17 years of age!) Somewhat surprisingly there were some really lovely shirt-dresses in eye-catching fabrics.

This was just the springboard I needed so, after a bit of a search through my patterns, I found this McCalls 7470 which had originally been free with Love Sewing magazine at some point in the recent past. The Princess seam lines and shirt styling were exactly what I wanted except I would change the skirt to be a dropped waist dirndl to echo the original.

The #7470 is a Palmer Pletsch fitting method pattern which I’ve never attempted before. I’ve been thinking lately that many of the garments I’ve made in recents months have either been old favourites or very simple shapes with little use of interesting techniques or style lines. I needed to stretch my sewing muscles a bit more-use them or lose them-so I set about following the instructions to tissue fit the bodice first. By a combination of body measurements, knowing my body quirks, periodically trying on the pinned tissue and using my padded-out dress stand Doris I arrived at a fit that I was happy with.

I’m not going to claim it was particularly easy but there are a lot of written instructions on how to approach it on the accompanying sheets to help you, plus online tutorials too. I’d recommend making a toile (or even two) if you need to before using your fashion fabric to avoid expensive mistakes.

I knew fairly early on that my 2 metres of fabric wouldn’t be enough for what I had in mind, and I didn’t want to waste my lovely Prada fabric so I opted to make the pattern instead in a vibrant printed stretch cotton which I’d bought in Paris at last year’s Sewcial event.

I took my time sewing the dress, I wanted to enjoy each part of the process. There is a two-part collar for example, pleated patch pockets with flaps, and a band running right down the front. I had a few problems with insetting the sleeves though. I’d made a small alteration the back of the arm scye which resulted in it getting a little smaller so I expected there to be a discrepancy but it was much bigger than I anticipated, the sleeve head was far too large and wouldn’t fit without puckering and gathering. I looked at a few examples of #7470 on Instagram and many versions were either sleeveless or didn’t mention it as a problem. Anyway, after a lot of fiddling about in the end I dropped the arm scye down to make it larger so that the sleeve head fitted properly.

The skirt was simply 3 rectangles, two for the front and one for the back which I pleated onto the shirt top using a fork to make each pleat even.

I used some plain white cotton scraps to make a faced hem.
I joined them into a long strip, folded lengthwise to about 5cms in width.
It was sewn onto the hem, all raw edges together.
At the centre front I enclosed it within the band for a neater finish.
the turned centre front band
the final stitched hem-it needs a good steamy press here. You can read more about hem finishes in my recent post here.

So what started as a Prada-inspired dress for one fabric has still ended up as a Prada-inspired dress but made in a different fabric! I finished the whole thing off with these beautiful buttons from Textile Garden all the way down the front.

the buttons look great
I love the detailed pockets too.
the collar is nice and crisp
the sleeves are two-part with a deep cuff
Yup, I’m happy with that!
I would have added a self-fabric belt like the Prada original but there wasn’t enough fabric left, just scraps.

So that’s my Prada-inspired dress up to this point, just not made with actual Prada fabric. I have a plan for it though because there was another shirt-dress that caught my eye…

I love the idea of a completely different fabric for the sleeves and the back
The front isn’t as I’d want it but I really like how the sleeves are such a contrast.

I’m really pleased with the outcome and the way it fits, and because I took my time and didn’t rush, it was an enjoyable process. I’d fallen into the habit of making simple projects, I felt something more complex was needed.

Until next time, happy sewing

Sue

A few hem finish suggestions-a Sew Over 50 topic

Over on the @SewOver50 account recently I shared a few of my favourite ways to finish hems or raw edges, although course it is absolutely NOT a definitive list by any means. I thought I would expand a little here on the blog using more photos of projects I’ve made in recent years. They are in no particular order either and if I wrote a blog post about the whole garment then I’ve linked it so you can read more if you want to.

Obviously there are the usual hand-finished hems using slip hemming stitch or herringbone stitch for example, which I use a lot too, but I thought I’d share a few alternatives which you might not know, or haven’t used for a while.

I’m beginning here with a faced hem…

This was the hem of the first Refashioners project I attempted. It was a jacket made from two pairs of my husband’s old jeans and because I wanted to use as much of the reclaimed fabric as possible I cut shaped facings for the lower edge. As you can see I also finished the edge with bias binding I made from offcuts of dress fabric.
The inside of the finished jacket looked like this. I understitched the lower edge of the facing to help it roll better and also slip-stitched it in various places including the seams and pocket bags to secure the facing without the stitching showing on the front.
This is also a much more shaped facing on the hem of Tilly and the Buttons Orla blouse. This can be a beautifully neat finish on a curve, it gives some ‘weight’ and crispness to the hem too and makes it less likely to curl upwards on blouses for example.
This Orla blouse was from 4 years ago, I like the exposed zip in the back too (the instructions for putting it in were excellent if I remember correctly)

The next one is an interesting hem finish which is very useful especially if you want a quality finish on evening or bridal wear. It uses something called ‘crin’, crinoline or horsehair braid (it doesn’t involve actual horsehair any longer though!) I’ve used it here on an organza skirt for the Dior New Look-inspired evening dress I made 4 years ago. As well as a crisp finish I wanted the hem to have distinct body and wave to it so this was the ideal technique. Crin comes in various widths, this was 5cms, lots of colours too because it’s more commonly used these days to trim hats and fascinators.

Helpfully, my fabric had horizontal stripes, some opaque and some sheer so I started by placing the crin on the front of the fabric and lining it up with the bottom edge of an opaque stripe. It is stitched on very close to the edge being careful not to stretch the crin as I sew, it’s important it lies flat. By sewing the crin onto the right side of the fabric when you flip it to the inside the raw edge of your fabric is enclosed underneath. To be honest I was making up the method as I went along because my experience of this technique previously came from altering wedding dresses which used it so this isn’t foolproof. I would strongly advise you to try a few samples first so that you have the version which looks best for your particular garment. [the eagle eyed amongst you might notice in my photo that I’ve sewn the crin to the wrong side of the fabric! I obviously did it and photographed it before realising what I’d done. As this was four years ago I don’t have any other photo!]
Once the crin is turned up to the inside I slip-hemmed it by hand, it looks a bit messy on the inside because the black shows up but it’s absolutely fine on the right side.
the finished dress, it’s one of my favourites I’ve ever made, and it’s a partial-refashion too because the velvet bodice used to be a skirt!

If you’re making a wedding dress for example and mounting all the skirt pieces onto another fabric, when you use crin on the hem (or bias binding for that matter) by hand-sewing the hem all your stitches will be invisible because you can catch them just through the mounting fabric. This is a couture technique so if you look at red carpet dresses with no visible stitching at the hem this will be how they achieved it. You can apply it as appropriate to any garment that you’ve mounted to another fabric though.

The next couple of photos are where I’ve used bias binding to neaten a hem. I find this a really useful technique if you need the maximum amount of hem because you can sew a very small seam allowance. It’s good if you’re letting down hems to gain length too, on trousers or children’s clothing for example.

Sew the binding on very close to the raw edge, this was a Simple Sew Lizzie dress
Here I made my own binding which is first sewn on with a 5mm seam allowance and then understitched which is what you see here. I made this Grainline Farrow dress for a magazine review
The hem is turned up and I’ve slipstitched it in place by hand.
This is the same technique with ready-made bias binding.
the finished skirt.
My final example is the little christening gown I made from a wedding dress.

If you have fine fabric why not consider using your overlocker if you have one on the rolled hem setting? Refer to your manual for specific instructions how to adjust your machine and make samples first to ensure it’s going to be satisfactory for your particular fabric. You’ll frequently see it used on chiffon or georgette but I’ve used it successfully here on fine cotton lawn, jersey and a stretch velour. If you don’t have an overlocker you can probably achieve a similar finish on your sewing using a rolled hem foot ideally and a small zigzag stitch-as always I would urge you to experiment to see what is possible. Some of the simplest machines can still give you an interesting variety of finishes.

This is one of my variations on the Camber Set
I roll-hemmed a straight strip of fabric here which I then pleated onto the sleeve using a fork!
I roll-hemmed a straight strip top and bottom and gathered it onto the sleeve here.
An extended length sleeve on the River pattern from Megan Nielsen, roll-hemmed and elasticated

I find the next couture/tailoring technique very useful on sleeves as well as coat, jacket or dress hems. I’ve used it here on my Tilly and the Buttons tester-made Eden. I wasn’t taught this method as such, I discovered it for myself whilst doing alterations taking up sleeves for people. I haven’t ever encountered it in pattern making instructions but I think it’s an excellent way of stabilising the cuffs of coats and jackets.

Using strips of iron-on interfacing to stabilise the area where the cuffs fold up
This is felted-type woollen fabric where hand stitching is unlikely to show through but if you have a finer fabric I would make the interfacing strip wider so that I then caught the inter with my stitches and not the fabric itself. See the next photo to explain this better.
You can see the interfacing is above the hem line here and I’ve herringbone stitched it by hand. You can also see how I’ve created a chain link to anchor the lining to vent opening on the back of the skirt.
the hemming stitches aren’t visible from the outside using this technique.

For this next finish I’ve used a triple straight stitch to create the effect of top stitching on the hem, and several seams, of this Simple Sew Zoe hack I made last summer.

If you have the foot attachment and stitch capability for your sewing machine you can always try blind-hemming. I must admit I don’t use it that often, and only then on completely straight hems. There is a bit of a knack to it and I tend to only use it on a busy print which will disguise any botched bits (yes really!) or if I’m tight for time compared with any other method. It’s not quite the same quality of finish you will see on RTW clothes though which uses a specific machine to blind stitch the hem.

Personally I always think the stitches show a bit too much no matter how hard I try to get them really tiny. It’s very easy to catch a bit too much fabric, or none at all! In truth I probably don’t practice enough!!
This Regatta dress from Alice & Co was an ideal application because the skirt has a straight, unshaped hem.

I think it’s worth mentioning that I like to use bias binding to neaten necklines (and armholes) too. I particularly like this as a way of avoiding using a neck or armhole facing which can be notorious for constantly rolling into view or flapping about annoyingly. The version you can see in the following two applications is a strip which I’ve folded in half lengthways first, the raw edges are matched and sewn. The seam is trimmed slightly and snipped if necessary, then turned so that the edge is enclosed and finally topstitched close to the folded edge to secure. In both the following examples I have sewn the binding on the wrong side of the fabric so that the binding turns to the outside to be visible and decorative but you could just as easily sew it to the right side so that it turns to the inside of the finished garment.

the binding is sewn on the inside first
the binding then flips to the outside to become visible.
This dress was made for the Simplicity pattern hacking challenge last year
Instead of the usual hem on this dress I created a casing which I threaded elastic through.

I’ve have included another variation of binding on a hem to show you how it can be combined with other techniques to achieve a quality finish. I used it here on a sheer organza which was mounted onto a backing fabric of slipper satin. This meant that when I turned the hem up the hand-stitching was invisible from the outside because the stitches only went through the mounting fabric.

the hem from the inside
the finished hem from the outside.
the finished dress, I was off to a wedding!

The next technique is more usually the choice of the pattern designer than the dressmaker, although if you know a little about pattern cutting you might be able to do it for yourself. This is an example of a deep grown-on faced hem on the Trend Patterns Square dress which I’ve made twice. It works brilliantly on this dress because the hem edges are straight (square!) plus it gives real weight to the hem which is another satisfying detail.

Inside the hem the corners are mitred.

Pin hemming is a technique I’ve used for decades on fine fabrics. You can replicate it using a rolled hem foot attachment on your machine although it can be trial and error which size works best for you with variable results. I have two different sizes of foot, 2mm and 4mm and I can’t get on with either, I’ve since been told that 3mm is the optimum size for most fabrics but I’m not prepared to risk another mistake when I know I can achieve a good quality result this way instead.

Simply put, I turn over the raw edge by approximately 5mm and stitch very close to the folded edge. Carefully trim the excess close to the stitching line and give it a light press. Then turn again and stitch a second time on top of the first row of stitching. This particular example is from the Trend Bias T-shirt dress I made a few months ago.

turn stitch and trim
make another narrow hem, stitch a second time on top of the first line. Press. There will only be one row of stitching visible on the outside.

If you read about my pattern hack of the Simple Sew Cocoon dress you will see how this variation of hemming came about. I added a large chunk of fabric to give extra length to a dress that would have been too short without it. This method is probably best on a straight hem, you could use it on sleeves too.

attaching a band to the hem.
The finished dress (worn with walking shoes during lockdown!)

This next one is a very much trial and error. I used an edging stitch on my Pfaff sewing machine to hem this Broderie Anglaise blouse which I made recently.

I put a piece of Stitch and Tear behind the fabric as I sewed.
It looked like this after I finished
It will look like this on the reverse.
gently pull away the backing and then carefully snip off the excess fabric up to the stitching line.
Eventually the hem looked like this, the sleeves are trimmed with Broderie Anglaise

I’ve used a variation of a faced hem recently when, instead of bias binding, I used straight strips of fabric to turn up a straight hem on a dirndl skirt. There will be a blog of this particular garment coming soon…

I had some narrow strips of white cotton lawn lying around so I joined them to make a piece long enough to go around the whole hem.
I folded the strip lengthwise.
attach the strip to the hem, raw edges together.
I understitched it, plus there’s a band on the front which is what you can see folded over in order to enclose the facing eventually.
The band folds back to enclose the hem facing.
There’s a little bit of puckering on the reverse here but this is invisible from the front, a good press will sort that out.

To finish with is a very simple method of rolling a fairly narrow hem. Overlock the edge first using three (or even two) threads then carefully turn it once and then again so that the overlocking is enclosed inside. If the fabric is quite ‘bouncy’ and won’t stay in position you could press the edge over once first and then roll it the second time. Whilst the result is wider than pin hemming it is narrower, and possibly quicker and more accurate, than a simple turned hem.

Stitching the hem with the overlocked edge rolled to the inside.

This last suggestion is from a project which will be blogged very soon. I cut 6cms wide bias strips which I used to create a self-neatening hem on a pair of pyjama shorts.

the bias strips were applied right side to wrong side on the shorts hems.
the bias strip is on the inside at the moment
It is then turned up to the outside where I trimmed and stitched it with ricrac braid.

I hope you’ve found my suggestions useful or thought provoking, is there something here which you’ve never encountered before, or that’s made you think how you could use a technique you already know in a different way? The idea is to show you a few ways of finishing hems, or raw edges, in new and interesting ways. I’ve not included the usual hand stitching methods because there’s nothing new to think about, although please let me know if you use these methods in a more unusual application. Just because the pattern instructions tell you to finish the hem a certain way doesn’t necessarily mean you have to do it that way…although think it through carefully just in case the really is a reason!

Until next time, Happy Sewing

Sue

Two years of Sew Over 50!! (where did that time go??)

So, here we are TWO YEARS on from the first SewOver50 post, on August 18th 2018, and the account now stands at nearly 21K members worldwide! 

Personally, I’d really like to thank Judith and Sandy for the amazing amount of work they undertake so graciously in order to steer the Mothership through some interesting and turbulent territory, especially the second half of these last twelve months. 

We were all trundling along in our own way when suddenly, in early 2020, the world went very weird indeed. As the impact of Covid-19 started to take effect many of us were locked-down at home, some still working but in a whole new way, reliant on technology to carry on, it was an extremely stressful time for many who could have no contact with their loved ones or friends, lots of sewing-related events we so enjoy were cancelled or postponed. Many of us found that our sewing and creative making was a safe haven amid what was going on around us. For example, did you make a pouffe? I had the luxury of being able to sew whenever I wanted, because I couldn’t go anywhere, and I noticed others embarking on this project so I took the opportunity to use up SO many scraps of fabric and stuff them all into a footstool, I made my own pattern but I know many of you used the ClosetCore free pouffe pattern. I know many others couldn’t sew as often but, from chatting with friends, the time that they were able eke out to sew was vitally important to them, helping them to de-stress and shift their focus for a while. Shopping for fabrics, patterns and haberdashery online became a way, almost the only way, of supporting some of our favourite businesses, as people found new ways to adapt and do business. Sales of sewing machines worldwide increased exponentially with many manufacturers and retailers struggling to keep up with demand. Some of us had sewing sessions with our friends via Zoom, which was occasionally technologically-challenging but it enabled us to be in touch with each other whilst participating in our shared interest. I’m not going to dwell here on the pandemic though because it’s been different for all of us, sewing and being in touch with my sewing friends around the world has been an absolute lifeline for me personally. In fact, rather than watching the all-too-overwhelming daily news stories, it’s enabled me to hear and appreciate what people I feel I’ve come to know have been going through. At one stage it seemed anyone who was able to was using their sewing skills to help with the desperate shortages by making scrubs here in the UK, and possibly elsewhere, and mask-making has become something that people with little previous sewing experience have found themselves being able to contribute. Face coverings have become compulsory in many places now so this will be an ongoing activity in future.

Moving on, as a group @SewOver50 has always strived very hard to be inclusive of anyone who wishes to follow along, after all, part of the reason it started in the first place was because we felt somewhat excluded from sections of the sewing community by virtue (?!) of our age. Following the murder of George Floyd in the US we were all called to question the part we play in our world, even within our sewing community we had to examine our consciences to ask if we were doing enough. #BlackLivesMatter was rapidly followed by #BlackMakersMatter and there is now an Instagram account @BlkMakersMatter where you can see, and follow and support, the massive diversity of BIPOC makers, and not just sewers but crafters and makers of many beautiful things. Many of our wonderful stalwart SewOver50 followers including Diary of a Sewing Fanatic are vocal advocates, I’ve always got time for Carolyn’s no nonsense plain speaking! We shall endeavour to continue reflecting our membership, and involve a diverse range of contributors and guest editors in the future. If you have ideas for future topics, especially if you think we’re missing something important, do please let us know.

So, very briefly, that’s the worldwide picture (as it currently stands) in which there have been quite a few SewOver50-related things going on during the past 12 months too. My personal favourite was our very first, and fortuitously timed, official meet-up in London in late February. Judith was able to join me to co-host and I was thrilled that so many generous companies large and small sponsored prizes for the charity raffle we held. I think, without exception, everyone who attended enjoyed themselves and agreed we would have liked even longer to chat and create new friendships in real life, just weeks later the event couldn’t even have happened. We had high hopes of more of you being able to host your own meet-ups where ever you are in the world but that’s still not really possible, make sure you let us know if you do manage it! Above all though, stay safe! 

still no luck for Judith using my homemade teleportation device…must try harder

Stalwart supporter Maria Theoharous in Sydney started her own podcast Sew Organised Style in September 2019 and she generously created a space for Sew Over 50 every Thursday! Judith, Sandy and myself have all chatted with her but you can also listen to a growing list of our fellow followers every week chatting about what sewing, crafting and Sew Over 50 means to them. It’s really lovely to actually hear their voices, talking with enthusiasm about things they are passionate about. 

At the beginning of May ClosetCore Patterns paid the ultimate accolade to one of my personally most inspirational sewers, Blanca, by naming a pattern after her, it’s a stylish flight/boiler/jump suit (call it what you will) but I love her personal aesthetic and she absolutely rocks this outfit! 

photo credit Blanca via Closet Core Patterns

In the UK during the spring, and at the height of lockdown, we had series 6 of the Great British Sewing Bee to enjoy. It featured several fellow dressmakers who we can claim to be representing ‘us’ on national TV. Yes, we know they are ticking boxes to cast certain ‘types’ but at least this time it’s positive discrimination! Even so, 10 weeks went by far too quickly!

Over the year the account covered all sorts of different topics for discussion including, do you always make a toile or just happy to wing it? What are you pet sewing peeves? (cutting out and pattern tracing seemed to be top for this one!) The art of tutu making was a personal favourite, having always loved ballet and especially the costumes. Tips for better and more accurate top stitching was another goody and @SewitwithDi gave us a master class in using the correct interfacings effectively. There are too many others to mention them all but you can refer back at any time, take a screen shot of your favourites or save them to your archive for future reference.

More recently the account reached, and has now surpassed, 20,000 followers! This was marked with a giveaway where two people who had not necessarily met in real life but had formed a friendship through sewing could each win a copy of the same pattern. If you take a look at the hashtag #so50sewalong you can see some of the garments that have been made since this competition ran a couple of months ago. Incidentally, it’s worth mentioning that the #sewover50 hashtag has now been used almost 80K times up to this point, it’s an absolute wealth of inspiration and knowledge which is all yours for the taking! 

I think many of us enjoyed the opportunity to look back through, and share, some of our holiday photos wearing our me-mades. Sadly many holiday and travel plans haven’t been able to happen this year so it was a lovely way for us all to virtually ‘travel the world’ over the course of a weekend. Lots of us wore those clothes anyway, even if we couldn’t leave home! The online virtual Frocktails in April was another excuse to dress up a bit, knowing our friends around the world were raising a glass to each other at (almost) the same time.

joining with Virtual Frocktails, my dress is self-drafted

Have you been keeping a #so50bingo card? This has been an ongoing way of keeping tabs on what you have been sewing and other techniques/events you could challenge yourself to try. No pressure, it’s just a bit of fun with no time limit. 

During the year I wrote several blog posts based around different topics including sewing advice for newbies (or returners for that matter) your go-to T-shirt patterns, what do you take into account with your fabric buying choices, are you a batch cutter/sewer or just one thing at a time? Judith and I both contributed videos as part of the online Sewing Weekender, this is normally an event held in Cambridge, UK but The Fold Line opened it up worldwide as an online event and it was a huge success with over 1,700 people ‘attending’ from all over the world. 

We also held the second #so50visible challenge earlier in the year, we seem to be having success with getting our images reposted by lots of pattern companies which is a very good thing but notably few are choosing older models-with a few honourable exceptions-to represent their patterns in the marketplace. This is still very frustrating when you look at just how many stylish and inspirational people follow this account but if we all keep plugging away a change will come. One thing that pattern companies have said to us is that the quality of photos isn’t always good enough for them to reshare so the better, and clearer, you can make your photos to show off your makes the more likely it is to get reposted. There have been a number of posts with simple tips on how to improve your photos so why not check them out?

Most recently our own Leader Judith has written an article for bi-monthly US-magazine Sew News talking about Sew Over 50, which you can order online.

So, in spite of everything, lots of good things going on for Sew Over 50 in the last twelve months, some progress being made with representation but I’m sure you’ll agree that isn’t all the account is about. I hope you continue to find the account as inspiring as I do? Yes, we all start off by being here for the sewing but it often becomes so much more than that. Real friendships have been forged as a result, very few of us have ever met one another in real life but that doesn’t stop us identifying and empathising with each other and the lives we lead, especially during these last few extraordinary months. 

I am deeply indebted to Judith and Sandy for the sheer dedication they have on our behalf, and I’d like to thank all of you for your kind words of encouragement, support and appreciation to me personally, I love being a part of this worldwide community of sewing and I can honestly say the last few months would have been very different without so many of you connecting and interacting with me in some way. 

Thank you, and until next time,

Happy sewing!

Sue

A Simple Sew Cocoon dress hack

I had made two Simple Sew Cocoon dresses without alteration when the pattern was first released a couple of years back, and you probably know that I love a bit of a pattern hack so I decided that the style would be good for an adaptation. I’d drawn a few sketches of ideas and had a rummage in the stash for some suitable fabric when a funny thing happened…

I found I had already cut out a hacked Cocoon in the past!! I realised I must have done it easily two summers ago but then abandoned it because I decided it would be too short. I remember it was a limited amount of fabric, probably 2 metres, but I put it to one side and forgot about it. 

Fast forward to now, I wanted to make it up but I needed to lengthen it in a way I was happy with. I had truncated the bodice at Empire line just below the bust and then the skirt was two widths of the fabric, a simple dirndl. I’d cut the facings too but there was literally nothing else left except small scraps.

There’s a centre front seam in the bodice, I cut the dress horizontally under the bust at about Empire line

I went through various options including adding extra frill layers but to do that you gradually increase the amount of fullness needed for each layer, in other words, layer 1 would be 1.5x the waist measurement, layer 2 could be 2x the length of layer 1, and layer 3 could be 3x the length of layer 2. In simple terms this means longer and longer strips of fabric are needed to form each frill to be sewn to the previous one, and the longer the length of the dress the more layers you might need. Basically I couldn’t make the skirt any longer with what I had because it was already cut, and because of the lockdown I couldn’t go out to look for a suitable plain cotton. I returned to the stash and eventually found 50cms of cotton poplin which I know I bought at the same time as the original, I must have intended it as a contrast but never used it.

By cutting the 50cms piece across the width into two 25cms pieces I could join them at the side seams to form a loop and then fold them in half to create a 12.5cms deep band which I would sew to the hem of the dress! Simple! 

Once I’d worked all this out I sewed up the bodice, rather than hemming the cap sleeves I used some binding from my stash so that I could maximise their length. I planned to twin needle some top stitching in various places and I used two different coordinating threads for this. 

Bias binding sewn onto the sleeve then understitched
bias binding turned back
The completed sleeve with twin needle topstitching

I did the same around the V neck once the facing was sewn on, in order to get a pristine join at the point I carefully unpicked a couple of stitches and secured them on the reverse.  

I wanted side seam pockets (of course) so I had to cut them out of some plain cotton scraps, each piece was added to the side seam and then the side seams sewn up. 

The new band was initially slightly wider than the lower edge of the skirt so I restitched it until the two were the same width and matched exactly at both side seams. I used the overlocker with four threads to join and neaten the band in one step, I pressed the seam upwards and then twin-needle topstitched it to decorate. 

the band folded and pinned to the lower edge of the skirt

The final step was to run two rows of gathering stitches at the top of the skirt then sew it onto the bottom of the bodice, matching at the side seams. I pressed this upwards too and topstitched it as well.

For a dress which had languished with not much hope for two years I’m really happy with it!! I loved the fabric (which was from John Lewis originally I think about 4-5 years ago!) and I was so cross I’d cut something which I couldn’t imagine I’d wear if I sewed it up. By adding the deep band the skirt now has weight as well as length. It’s been so comfortable in the hot weather, why did I wait so long?!

we were heading out for our exercise hence the unsexy shoes!
we have a Henry Moore sculpture on loan for the duration of the centenary year of our town, maybe we can keep it for an extra year now that all the summer celebrations are cancelled?
Coronation Fountain
yes I have got water coming out of the top of my head!

Lockdown is easing in the UK since I originally finished this dress but I hope, as always, this hack has given you an idea of how simple it can be to take a section of a pattern you already have and give it a twist to become a different garment. I had very limited fabric with a print which still needed to match everywhere, by adding the hem band I’ve given it the look I was after…it just took a couple of years to think of it!

Until next time, happy sewing,

Sue

New Trend pattern TPC26 plus tips for handling a tricky fabric.

Firstly, I probably need to give you a quick explanation of why I’m making a fancy frock during the lockdown because it must seem rather incongruous.

This is my first post as a Lamazi Fabrics blogger and before the Covid-19 pandemic reared it’s ugly head I had offered to make an outfit using a slightly ‘tricky’ fabric in order to share a few hints and tips for sewing with it. I selected the beautiful Tencel/Cupro ‘Bark’ fabric in Lavender because we were going to a wedding in late May which would be the perfect chance to make a something using this special fabric. Very sadly that wedding is now postponed indefinitely but I’m making the dress because I’ll still need something to wear when it’s rescheduled. 

The fabric has a lovely weight and handle which makes it drape really well. It’s has a bark-like finish and is different on each side, you could use this to your advantage if you want to create an interesting visual effect by having some pieces with one side out and some using the reverse side. 

I made life harder for myself by choosing the new Bias T-shirt Dress by Trend patterns (generously gifted to me by them) in which EVERY piece except the sleeves are singles and strange shapes which means you cut everything out on a single layer of fabric right side up (RSU). Unlike most patterns, when you are cutting pairs of parts you can usually flip a piece without too much difficulty, however if you do that for a piece which must be cut RSU you would have completely reversed the print/design to the wrong side when you try to sew it up. This Tencel/Cupro has a nice look whichever side you use but my advice is to be really careful on printed fabrics before reversing any piece labelled RSU. 

Next, when cutting slippery or fluid fabrics (unless you have a lovely big cutting table) you’ll need to handle them as little as possible (by which I mean pulling them about to get them into position) which might be easier said than done. I know that cutting out is most people’s least favourite part of sewing but it’s so important to take time and care at this stage. If you’re cutting out on a table with straight sides use the edges as a visual marker to get the end of your cloth at a right angle to start with, ensure the weft (across the fabric) is nice and straight as well as the warp, pull a few threads to find the grain if necessary. If you have more cloth than will fit on the table in one go you could try having the excess rolled on a cardboard tube if you have one to keep it under control rather than sliding off the table all the time. 

Because my pattern has large awkward-shaped pieces cut from a single layer I had no option but to cut out on the floor! This can be physically quite tiring so you might want to get help if you need to. This is slippy slidey fabric so an extra pair of hands could help you lay it up nice and straight, again, rolling the fabric onto a long cardboard tube would also help keep the fabric taut and straight as you lay it out on the floor. This is not a fabric to use weights and a rotary cutter on unless the whole lot fits onto a cutting board without disturbing the fabric, if you’re spending time laying up the fabric carefully so that the grain lines are straight in both (warp and weft) directions you can’t then mess it about shifting a cutting mat underneath it and the pattern pieces need to be secured in place with pins. Cut out carefully moving the pieces as little as possible and try to keep them flat after cutting until you’re ready to sew. All of this will help minimise the pieces stretching out of shape, especially as a lot of this pattern has seams running on a diagonal. 

I felt that the length of the dress would probably be too long for me so I took some of the length out of the skirt pieces before I cut them out in fabric.
I calculated that approximately 5 cms would be sufficient to take out of the length so first I drew a line at a right angle to the grainline, then a second line 5cms from the first.
I pinned each piece to it’s ‘partner’ so that I could see if it would still align correctly after I folded out the 5cms.
It was really just educated guesswork but, eventually, by folding out the 5cms horizontally from each panel I was reasonably confident it would be pretty close.
Why didn’t I just take it off the hem at the end? You could easily do that but because I had just 2.5m of fabric, which may not have been quite sufficient, I could not take that risk so I did it this way instead. It took longer but removed the element of uncertainty.
This is almost everything laid up on the floor, I cut a linen version at the same time which is what you can see on the top. Whilst a single layer is often a very economic way of cutting fabric it’s usually more time-consuming to cut out so I did the two at the same time which was slightly risky but it worked out.

Once I’ve finished cutting out it’s vital to transfer all notches and mark darts and a couple of pivot points so I use old-fashioned tailor’s tacks (obviously you can use a textile marker pen if you prefer, I often do but it’s a pale fabric and I didn’t want to risk any marks being left) It’s a habit of mine to keep all the pattern pieces attached by just a couple of pins to the fabric until I need it, so that I don’t them get muddled. These are curious-shaped pieces so the chance of having them the wrong way round could be quite high! Next I stay-stitched all the neck edges on the machine 5mm in, if you have a very loose weave fabric it would probably be sensible to stay-stitch the bottom edge of the front bodice piece to prevent stretching. If you’re using a particularly fine fabric like chiffon you should stabilise the neck, and any other seams which could stretch, by hand-stitching very narrow cotton tape or ribbon over the seam line on the wrong side of the fabric. When I worked for bridal designer David Fielden many years ago we would cut the selvedges off the silk habutai linings for the seamstresses to use on necklines.

There is just a little fraying on the cut edges which I overlocked singly as I went along, as per the pattern instructions. Whether you’re sewing or overlocking the fabric I strongly suggest you have the whole piece supported on the table in front of the machine rather than feeding up from your lap. This is to prevent the piece becoming stretched as you’re sewing and possibly causing it to become misshapen.

If you find, as I did, that there’s a slight discrepancy between two seams (assuming that it isn’t an error in cutting or adjustment of the pattern) then pin it with the excess on the underside so that when you sew the feed dogs will take up the ease.

You can see the lower layer is a little longer than the top one and by sewing it with this on the underside means the feed dogs should take up the excess.
After sewing but before pressing it looked like this.

My photos should make it clearer, a good press will help steam out some of the excess too. Also, to minimise the risk of making a shiny patch on the fabric make sure you use a pressing cloth, you can often buy silk organza ones although I have a piece of plain fine pure cotton lawn which I’ve overlocked around the edge. I use this when I’m pressing darts or turning points or corners out too.

To sew an invisible zip into the diagonal seam across the back I machined the seam closed but I used a long basting stitch just for the section where the zip will go. This stitching will be removed later.

Line up the teeth with the basted part of the seam, this has been lightly pressed open already.
Pin the zip tape to the seam allowance with the seam and teeth matching.
I prefer to tack the tape to the seam allowance at this point but you could use Wonder Tape if you have it.
Now I removed the basting stitches and sewed the zip in using an invisible zipper foot. The zip I was using was longer than I needed.
Make a new stopper for the zip by carefully sewing backwards and forwards a few times over the teeth, cut off the excess then secure each side of the tape to the seam allowance using a regular zip foot.

Once the zip was in and side seams sewn up I checked the fit on myself. I cut a UK 16 and overall I’m happy with the fit and apart from the length I made no alterations to the bodice. Because I made the linen version first I already knew that the shoulders were a bit too broad for me and the sleeves dangled too much off the crown of my arm. I calculated that I needed to remove approximately 3cms to lift them up to a slightly better position. I found I didn’t need to alter the sleeve head though, fortunately it still fitted into the armhole. Another thing I did decide at this point was that the sleeve needed ’something’ else so I mocked up some small pleats and pinned the sleeve into the armhole to try out the effect.

I mocked up some small pleats with the sleeve pinned into the armhole.
I drew some markings so that I could then transfer the pleats equally to both sleeves.
More old-fashioned tailor tacks to mark the pleats.
The pleats are equally divided across the centre line of the sleeve.

After making the pleats in the sleeves and sewing up the underarm seam I used a ‘pin hem’ to finish the edge. This is similar to a simple rolled hem but even narrower. Begin by stitching a turning of approx 1cm very close to the edge, trim this carefully  

Sewing a pin hem, this is useful technique well worth mastering because if you haven’t got a rolled hem foot which could do the job, this gives a beautiful hem finish to fine or delicate fabrics.
Finished pin hem on the sleeve
Because I’d made the pattern alterations to the skirt length I wasn’t surprised to find there was a slight discrepancy in levels at the hem. Using a long ruler I averaged out a new straight line and then pin-hemmed it.

I love the 1930s/40s vibe of this dress, the drapey qualities of the fabric enhance the bias lines of the skirt in particular. I really enjoyed the challenge of putting the dress together, there are no particularly difficult techniques as such but it’s an interesting puzzle which you’ll need to spend a little time concentrating on, you’ll be rewarded with a striking but really wearable dress.

Thank you to Trend Patterns for gifting me the pattern, there was no expectation to write a review. You can read my previous review of the Square Dress pattern here. The fabric was provided by Lamazi Fabrics in return for a review which is also published on their own website.

I hope you find some tips and advice in here that might be of use to you if you’re thinking of using a fabric that needs a bit more forward planning than you’re used to. Trend have created another beautiful pattern with stunning and unusual details but the pieces cleverly work with the grain of the fabric so that working with the bias cut is a lot easier than it usually is. They have been gradually increasing their size range too so the TPC26 comes in UK sizes 6-22.

Quite a long blog this time so thank you for reading this far and, until next time,

Happy Sewing

Sue

Simple Sew Chelsea Collection blouse hack.

A lot has happened since I wrote my last Simple Sew blog post, Christmas for one thing, and I had a lovely holiday in the sunshine too but now we are all confined to our homes because of Covid 19. Without wishing to trivialise the gravity of this situation, one of the side effects of it is that you might have more time to sew. 

I’ve had a rummage through my Simple Sew patterns to find one which I haven’t already shown you, and which has opportunities to hack, and I settled on the Chelsea Collection. This is a capsule wardrobe of a short sleeve blouse with two variations, a pair of trousers and a button-front skirt in two lengths. I liked the blouse with it’s shirred sleeves and keyhole back detail but I decided to mix it up a little by adding a button front. Normally we are able to select fabric from a couple of generous sponsors but I wanted to ‘shop my stash’ to find something this time. I found a very pretty vibrant floral John Kaldor cotton lawn which I think I picked up from a swap table sometime and I knew would work well for the blouse. 

I didn’t want the blouse to be overly tight so, after checking my measurements I opted for a larger size than I’ve made previously. If you’ve been a regular reader of my posts you’ll know that I tend to check Simple Sew patterns for any discrepancies before I start. There didn’t seem to be any glaring ones but I just added a slight curve to the back hem so that it dipped in the same way as the front and I trued the shoulder seams so there was a smooth flow from front to back. 

Adding a curved hem to the back, I measured the distance from the lengthen/shorten line on the front then made the back the same amount, curving the line gently upwards to the side seam.
trueing the shoulder seams

As I wanted to alter the front significantly I had to make some changes there first. In order to create a button-stand I simply added 2.5cms to the centre front all the way down what would have been the fold. [2.5cms was a fairly arbitrary figure because it depends really on what size buttons you’re using, a general rule of thumb is that the bigger the button the bigger the button-stand needs to be so that there’s enough overlap and the garment doesn’t end up too tight because the overlap isn’t big enough.]I was able to do this by drawing directly onto the tissue before cutting the piece out as there was enough space to do so.

adding the button stand to the front

If you’ve already cut a pattern that you want to add to just stick some extra paper to the centre front fold line, or trace off the whole piece again adding the extra. The original front had a facing for the neckline so now I needed to create a new facing which would neaten both the neck edge and the button-stand. To do this I simply traced off the whole of the new front opening including the neck edge and made the facing a depth of 7cms all the way down from shoulder to hem, with a smooth and gradual curve. The photo should make this clearer. The back neck needed a new facing too because the existing one took the armhole into account. Again I traced off the section I needed making it 7cms at the shoulders to match the front facing. 

The final change I made was to lengthen the sleeve a little and add some more fullness to it. I started by making the sleeve 5cms longer and then I drew 3 vertical lines on the pattern at approximately the front notch, back notch and shoulder seam points. [Depending how much extra fullness you want to add to a sleeve you could use more places than this but do try to space them evenly apart.] Next I cut up each line from the bottom until I reached almost the top, I left this very slightly attached. With the piece flat on the table I spread the bottom of each slit by about the same amount, probably about 4 cms, then taped slithers of paper into each gap.

First I added the extra length and then drew the vertical lines where I wanted the extra fullness.
Next I opened each part to add the extra being careful to keep the pieces flat and not twisting or wrinkling up, put extra pieces of paper under the gaps. Once you’re happy tape them in position,
Once I had added the extra I cut the piece out.

If you don’t want to cut the pattern up you can do the same process by still marking the vertical lines on then pivoting the uncut pattern at the top of each line, use a pencil or your finger as the axis. Draw or trace around the first section, which remains stationary, then each subsequent section after you pivot it to so that you get the extra fullness being added at the hem. Opening up the wedges in this way means you’re adding fullness to the hem but not the crown of the sleeve, if you want extra fullness in the crown spread the whole piece more or less parallel. The grainline should run equidistant down the centre of the new piece (unless you want to cut it on the bias)

Having done all this I cut it out and was ready to sew! 

I started by joining the shoulder seams of both the blouse and the facings (which I’d interfaced and neatened) then I attached the facings to the neck edge, turned, understitched and pressed. The keyhole back calls for a small rouleau tube as a button-loop which needs to be inserted at the same time as applying the facing although you could choose to make a hand sewn thread loop and stitch that at the end. In fact it isn’t even vital that this is a functioning loop if you’ve got a front opening, the keyhole is purely decorative now. 

I put the blouse onto Doris to check it was looking OK and this was when I found that the keyhole appeared to be bagging outwards quite significantly. I decided not to do anything at this point and I would check again once I had sewed the side seams and put the sleeves in, then I would get a better idea by trying it on myself. 

Checking the front neck
With the loop pinned I discovered that the keyhole didn’t sit flat.
It seems to stick out quite significantly on Doris.
If the button isn’t done up it would look like this.

I made three rows of shirring on the sleeves next, using my quilting guide to make sure the first row was 5cms from the bottom edge, the next two rows were then sewn parallel to the first. [Refer to a previous blog post on how to sew shirring if you haven’t done so before] Next I sewed up the sleeve seams and pin-hemmed the bottom edge to give a neat finish.

I positioned the needle 5cms from the cut edge and the quilting guide helps me as a visual marker to keep it parallel all the way.
Shirring is stitched from the right side so that the elastic is on the reverse. Use a long straight stitch, secure both ends and then apply plenty of steam to shrink up the stitching further.
finished sleeve

After sewing up and neatening the side seams I inserted the sleeves. At this point I tried the blouse on again to check the keyhole on myself and, with real shoulder blades under it, it didn’t seem so noticeable. Two other things struck me though, the blouse was a little too big so I took it in on the side seams and also the blouse was a bit shorter than I expected. In order to take as a small a hem as possible I made some bias binding from offcuts of the fabric then stitched it (folded in half lengthways and with the cut edges together) to the hem using a narrow 5mm seam allowance [This is a useful finish to any hem or edge where you need every spare centimetre of fabric.] Have a look at the photo which shows you how to get the ends of the binding enclosed within the front facing. I turned the binding up and top-stitched in place. 

If you’re adding binding when there’s also a facing pin it like this so that the end is neatly enclosed inside the facing when it’s turned right side out.

Finally, I found some ‘vintage’ buttons amongst my treasure trove and there were just the right number meaning the whole blouse had been sourced from what I already have!

Well I hope now that I’ve made it that I’ll have a chance to wear my Chelsea blouse somewhere other than in my own garden this summer, who knows? Maybe you’re reading this long after the emergency ended and life has returned to some sort of normality, although it definitely won’t be exactly as it was before.

Sewing our own clothes is an activity which gives us so much enjoyment for a variety of different reasons and, right now, the simple act of creating something is chief amongst them for me. It’s absorbing and the problem-solving gives me something else to think about.

I think the keyhole back is, by and large, just about acceptable when I’m wearing the blouse. I also think the cure could be to add a centre back seam instead of cutting on the fold so that the point of the keyhole could extend beyond the centre back line, this would hopefully bring the button and loop closer to one another when they are done up…this is just my theory based on experience and I haven’t tried it out. It’s such a nice little detail that I’m disappointed it hasn’t worked out quite right. I also regret not reading my fellow Simple Sew bloggers reviews of the blouse because then I would have known how short it comes up, personally I would add a minimum of 8-10cms to the length next time.

The sleeves are pretty and feminine but maybe they are a little too girly, the jury is out…

Until next time, happy sewing

Sue

The first official Sew Over 50 meet-up

After a couple of months in the planning I can hardly believe that the first ‘official’ Sew Over 50 meet-up is over! This isn’t really a blog as such, it’s more of a photo album so that those who were there can look out for themselves and to prove that it did happen and a great time was had, new friendships were made, information and tips were shared, fabric was stroked and support and encouragement was offered. 

Judith and I were simply overwhelmed by the feeling that was in the room for those 3 hours. The Village Haberdashery in West Hampstead, London proved to be the perfect venue to hold the meet-up with it’s mix of light-filled studio space and retail opportunities! Whilst quite a few of us already knew one another, and had met in the past, there were many others for whom this was the very first time they had gone to such an event. The distances some people travelled was extraordinary too, south Wales, Cumbria, Cheshire and north west England, Scotland, East Anglia, the south coast and Cologne, Germany were just some of the places people had come from. This represented a really big deal for some because it took them a long way outside their personal comfort zone to go on a long train journey to London and meet lots of strangers who they only ‘knew’ through the medium of little Instagram squares. So far as we can tell all of them thought it had been worth the effort and anxiety because within minutes of arriving they were chatting with fellow sewers and crafters as though they had known each other for years. That’s what the Sew Over 50 community seeks to encourage, to nurture and expand each others skills and talents, we try to make it a positive and supportive place to share our makes whether they are completely successful, or a dismal failure! 

I would personally like to thank every single one of the companies and individuals who gave me prizes for the charity raffle in response to my requests, and several others who offered without me even asking. 

Have a browse through the photos (please ask permission and credit me if you would like to use them elsewhere though, thank you) these are just a few of the hundreds that my daughter Bryony took for us but without them I don’t think there would be much record of the event having taken place…hardly anyone else took photos because they were too busy chatting!

unpacking the cake!
starting to arrive
the chatter gets going
The Village Haberdashery before we filled it up!
Marcia and Ana in the queue to get in
Val and Gilly came a very long way and had never been to a meet-up before but they had a great time
one question which never got asked was “did you make that?” because, obviously, we DID! More likely was “which pattern is that?” or “where’s that fabric from?”
pattern designers Marilla Walker and Ana Cocowawa Crafts who both donated prizes
what’s in the bag?
It’s a handmade plaque made especially for me by Jayne Wright, who also donated two handmade ceramic hedgehog pin-cushions (Threadquarters is the name of my workroom in the garden) Thank you so much Jayne
Judith and Lisa Bobo Bun who had come all the way from Norwich
Sara telling Jo all about sway back adjustments
I love this one, setting up for a selfie!
when Insta-friends finally meet in real life
this made me smile, Judith and I mirroring each other…
Ex-Brownie leader waiting for quiet
Ceramicist extraordinaire Corrie with our Great Leader, naturally she’s wearing one of her own handmade brooches
Susan and Amanda Patterns and Plains who generously offered a prize without me even asking
sorry Marilla but this was the best photo without one of you having closed eyes!
the much-admired cake made by Mr Y, it was universally agreed that it was a delicious fruit cake! ( and now he won’t let me forget it!)
busy in the shop now too
I love how during the course of the afternoon people are in different shots talking to different people all the time.
None of these ladies knew each other before they arrived but they got on like a house on fire
having a really good natter
my raffle ticket-selling friends Sara and Di
Me and lovely Ruth, whose son kindly donated a fabulous designer Anglepoise lamp which was much-coveted in the raffle.
Sharon (with the shoulder bag) is the talent and the brains behind Maven Patterns and generously donated 3 patterns to the raffle
group shot-it was a bit like herding cats but I think we got virtually everyone in
gathering to draw the raffle
by the wonders of WhatsApp I’m telling Kate (who was in Stockholm) that she had won a prize
She had won some lovely Lamazi fabric
with my fellow Love Sewing magazine photo-shoot friends, minus Kate and Sarah who couldn’t be with us. Love Sewing donated a one year subscription
this is us with former editor Amy and we featured in the February 2019 of Love Sewing magazine
designer Lucy of Trend Patterns donated two, here’s Charlotte with her prize
Corrie was thrilled with her Anglepoise, she’d been coveting it right from the beginning!
Sue was over the moon to win a Pfaff Passport 3.0
Judith trying out my teleportation device fashioned from an old hairdryer and sticky-back plastic. It didn’t work so it’s back to the drawing board for me!

I had opted to raise funds for The Samaritans, a UK-based charity who offer support at the end of the telephone to those at risk of suicide and the raffle made over £550 which is magnificent.

Thank you so much to everyone who came along and made it so enjoyable, thanks especially to Judith for having the courage to start the account in the first place. We’re approaching 18K followers and there have been almost 52K uses of the hashtag #sewover50 That’s a LOT of work which Judith and Sandy put in every day to ensure it’s such an enjoyable, interactive and mutually supportive community. I for one hope it continues this way. I’m sorry to those of you who couldn’t get a ticket, or are simply too far away, we want to actively encourage you to create your own meet-ups like this, there was no sewing at this one but you just need a venue where you can chat, a friendly cafe? your local sewing shop? Now we’ve started the ball rolling don’t forget to use the hashtag #so50meetup so we know what you’re up to.

Now, back to some sewing for a while!

until next time,

happy sewing

Sue