Simple Sew Chelsea Collection blouse hack.

A lot has happened since I wrote my last Simple Sew blog post, Christmas for one thing, and I had a lovely holiday in the sunshine too but now we are all confined to our homes because of Covid 19. Without wishing to trivialise the gravity of this situation, one of the side effects of it is that you might have more time to sew. 

I’ve had a rummage through my Simple Sew patterns to find one which I haven’t already shown you, and which has opportunities to hack, and I settled on the Chelsea Collection. This is a capsule wardrobe of a short sleeve blouse with two variations, a pair of trousers and a button-front skirt in two lengths. I liked the blouse with it’s shirred sleeves and keyhole back detail but I decided to mix it up a little by adding a button front. Normally we are able to select fabric from a couple of generous sponsors but I wanted to ‘shop my stash’ to find something this time. I found a very pretty vibrant floral John Kaldor cotton lawn which I think I picked up from a swap table sometime and I knew would work well for the blouse. 

I didn’t want the blouse to be overly tight so, after checking my measurements I opted for a larger size than I’ve made previously. If you’ve been a regular reader of my posts you’ll know that I tend to check Simple Sew patterns for any discrepancies before I start. There didn’t seem to be any glaring ones but I just added a slight curve to the back hem so that it dipped in the same way as the front and I trued the shoulder seams so there was a smooth flow from front to back. 

Adding a curved hem to the back, I measured the distance from the lengthen/shorten line on the front then made the back the same amount, curving the line gently upwards to the side seam.
trueing the shoulder seams

As I wanted to alter the front significantly I had to make some changes there first. In order to create a button-stand I simply added 2.5cms to the centre front all the way down what would have been the fold. [2.5cms was a fairly arbitrary figure because it depends really on what size buttons you’re using, a general rule of thumb is that the bigger the button the bigger the button-stand needs to be so that there’s enough overlap and the garment doesn’t end up too tight because the overlap isn’t big enough.]I was able to do this by drawing directly onto the tissue before cutting the piece out as there was enough space to do so.

adding the button stand to the front

If you’ve already cut a pattern that you want to add to just stick some extra paper to the centre front fold line, or trace off the whole piece again adding the extra. The original front had a facing for the neckline so now I needed to create a new facing which would neaten both the neck edge and the button-stand. To do this I simply traced off the whole of the new front opening including the neck edge and made the facing a depth of 7cms all the way down from shoulder to hem, with a smooth and gradual curve. The photo should make this clearer. The back neck needed a new facing too because the existing one took the armhole into account. Again I traced off the section I needed making it 7cms at the shoulders to match the front facing. 

The final change I made was to lengthen the sleeve a little and add some more fullness to it. I started by making the sleeve 5cms longer and then I drew 3 vertical lines on the pattern at approximately the front notch, back notch and shoulder seam points. [Depending how much extra fullness you want to add to a sleeve you could use more places than this but do try to space them evenly apart.] Next I cut up each line from the bottom until I reached almost the top, I left this very slightly attached. With the piece flat on the table I spread the bottom of each slit by about the same amount, probably about 4 cms, then taped slithers of paper into each gap.

First I added the extra length and then drew the vertical lines where I wanted the extra fullness.
Next I opened each part to add the extra being careful to keep the pieces flat and not twisting or wrinkling up, put extra pieces of paper under the gaps. Once you’re happy tape them in position,
Once I had added the extra I cut the piece out.

If you don’t want to cut the pattern up you can do the same process by still marking the vertical lines on then pivoting the uncut pattern at the top of each line, use a pencil or your finger as the axis. Draw or trace around the first section, which remains stationary, then each subsequent section after you pivot it to so that you get the extra fullness being added at the hem. Opening up the wedges in this way means you’re adding fullness to the hem but not the crown of the sleeve, if you want extra fullness in the crown spread the whole piece more or less parallel. The grainline should run equidistant down the centre of the new piece (unless you want to cut it on the bias)

Having done all this I cut it out and was ready to sew! 

I started by joining the shoulder seams of both the blouse and the facings (which I’d interfaced and neatened) then I attached the facings to the neck edge, turned, understitched and pressed. The keyhole back calls for a small rouleau tube as a button-loop which needs to be inserted at the same time as applying the facing although you could choose to make a hand sewn thread loop and stitch that at the end. In fact it isn’t even vital that this is a functioning loop if you’ve got a front opening, the keyhole is purely decorative now. 

I put the blouse onto Doris to check it was looking OK and this was when I found that the keyhole appeared to be bagging outwards quite significantly. I decided not to do anything at this point and I would check again once I had sewed the side seams and put the sleeves in, then I would get a better idea by trying it on myself. 

Checking the front neck
With the loop pinned I discovered that the keyhole didn’t sit flat.
It seems to stick out quite significantly on Doris.
If the button isn’t done up it would look like this.

I made three rows of shirring on the sleeves next, using my quilting guide to make sure the first row was 5cms from the bottom edge, the next two rows were then sewn parallel to the first. [Refer to a previous blog post on how to sew shirring if you haven’t done so before] Next I sewed up the sleeve seams and pin-hemmed the bottom edge to give a neat finish.

I positioned the needle 5cms from the cut edge and the quilting guide helps me as a visual marker to keep it parallel all the way.
Shirring is stitched from the right side so that the elastic is on the reverse. Use a long straight stitch, secure both ends and then apply plenty of steam to shrink up the stitching further.
finished sleeve

After sewing up and neatening the side seams I inserted the sleeves. At this point I tried the blouse on again to check the keyhole on myself and, with real shoulder blades under it, it didn’t seem so noticeable. Two other things struck me though, the blouse was a little too big so I took it in on the side seams and also the blouse was a bit shorter than I expected. In order to take as a small a hem as possible I made some bias binding from offcuts of the fabric then stitched it (folded in half lengthways and with the cut edges together) to the hem using a narrow 5mm seam allowance [This is a useful finish to any hem or edge where you need every spare centimetre of fabric.] Have a look at the photo which shows you how to get the ends of the binding enclosed within the front facing. I turned the binding up and top-stitched in place. 

If you’re adding binding when there’s also a facing pin it like this so that the end is neatly enclosed inside the facing when it’s turned right side out.

Finally, I found some ‘vintage’ buttons amongst my treasure trove and there were just the right number meaning the whole blouse had been sourced from what I already have!

Well I hope now that I’ve made it that I’ll have a chance to wear my Chelsea blouse somewhere other than in my own garden this summer, who knows? Maybe you’re reading this long after the emergency ended and life has returned to some sort of normality, although it definitely won’t be exactly as it was before.

Sewing our own clothes is an activity which gives us so much enjoyment for a variety of different reasons and, right now, the simple act of creating something is chief amongst them for me. It’s absorbing and the problem-solving gives me something else to think about.

I think the keyhole back is, by and large, just about acceptable when I’m wearing the blouse. I also think the cure could be to add a centre back seam instead of cutting on the fold so that the point of the keyhole could extend beyond the centre back line, this would hopefully bring the button and loop closer to one another when they are done up…this is just my theory based on experience and I haven’t tried it out. It’s such a nice little detail that I’m disappointed it hasn’t worked out quite right. I also regret not reading my fellow Simple Sew bloggers reviews of the blouse because then I would have known how short it comes up, personally I would add a minimum of 8-10cms to the length next time.

The sleeves are pretty and feminine but maybe they are a little too girly, the jury is out…

Until next time, happy sewing

Sue

3 thoughts on “Simple Sew Chelsea Collection blouse hack.

  1. Thank you for an excellent post – full of excellent tips on fitting and construction. I have never made a keyhole opening but I guess that it is very tricky to get the perfect fit for this feature. I think that the fabric really suits you. I love the blouse on you, although I would agree that it needs a bit more length. I loved your sleeve adaptation but would agree with your opinion that it is a bit “ girly” . I think that a narrow cuff would look better on sophisticated mature women like ourselves 🙂

    Liked by 1 person

  2. Love love love the fabric you used for your blouse! So cheerful. I think it looks wonderful on you.

    The button-front skirt though; my girls would have a fit over something like that! Must see if I can get my hands on this pattern.

    Liked by 1 person

  3. So many helpful tips in this well written blog. Thank you for going to so much trouble. I found it inspirational. The blouse is lovely on you. It is a beautiful material and all your modifications add to its uniqueness. I agree with what you say about setting yourself little puzzles to solve and the absorption of that. Wishing you well, Susan, and thank you.

    Liked by 1 person

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s