Simple Sew Palazzo Pants

I decided to try something different to dresses from the Simple Sew collection for my blog post this time so I’ve chosen the wide-legged Palazzo pants. 

I always have a look at any posts or reviews about a particular Simple Sew pattern first to check if there are any pitfalls I should look out for which might influence my decision, or how I tackle making it, and the overall opinion of trousers was positive. I sorted out some fabric from deep in the stash, it’s a viscose from the now-defunct Adam Ross fabrics which has a good drapey quality, although I know it will crease so I’ll wear these permanently standing up! 

There are only 4 pattern pieces to the trousers-front/back/waistband/pocket- which makes them very simple to lay up and cut out, you could even leave out the pockets if you’re short on fabric but why would you leave out pockets?! 

I checked my measurements against the chart to decide my size, I also measured the pattern pieces to get some idea of the ease involved but I was optimistic they would be generally OK. If you’re very unsure, or between sizes, I’d suggest you make a toile that’s about mid-thigh in length to check the fit and comfort around your waist, hips and body length. Leave out the pockets at this stage, there are darts in the back and the front is flat, you could insert a zip in the back if it makes things easier to fit yourself but I didn’t bother. Always sew a toile as accurately as you would the garment itself because if you don’t bother cutting properly or following the seam allowances how will you know where the problems lie? That’s the whole point of a toile! Make any adjustments on the toile and transfer the changes to the pattern pieces. There are no lengthening/shortening lines marked on the pattern so I suggest, if you need to make either of these changes, drawing a line at a right angle to the grainline at a point midway between the waist and crotch level. Fold out or add in length through this line. 

It wouldn’t be a Simple Sew pattern if there weren’t some errors to keep you on your toes and this is no different. On the back piece the pocket placement notches are only printed on size 8 and none of the others. Either transfer the markings to your size or remember to snip them when you’re cutting out the back.  

the notches don’t feature on all the size lines so transfer them across as required.

The lay plan for cutting out shows the main pieces interlocking, which is fine if you have plain or multi-directional fabric but don’t forget to keep the pieces running the same way if you have a distinct one-way print. Also, I didn’t cut out the waistband until I was happy with the fit of my trousers as it’s very shaped piece and if it’s too big or too small you’ll probably need to cut another. Don’t forget to make a snip for the centre back on the waistband, it could have done with a notch for the side seam position though as there isn’t one so it’s guesswork.

I’m not normally an advocate of overlocking the edges until they’re sewn up [because you if you aren’t careful you can easily lose too much seam allowance in the trimming and when you join pieces together you could start to make the garment too small, plus your notches disappear] but, as many of the pieces here require the seams pressed open and flat, I overlocked most pieces first this time. 

You will find that for instructions 4 and 6 the words don’t match the diagrams but the drawings are correct 

Next the pockets go in (unless you wish to check the waist/hip fit first in which case tack or machine baste the side seams and leave the back open where the zip will be inserted in order to try the trousers on) The pocket insertion is easy enough, follow the instructions carefully and don’t sew the sew the openings shut by mistake! Also, don’t forget to sew the bottom of the pockets or all your sweets will fall out down inside your trouser leg!! 

After I’d assessed the waist size (comfortable to loose) and crotch length (comfortable) at this point I cut and interfaced the corresponding waistband [for some reason there are two waistbands printed out but I could find no discernible difference between them so just ignore one and cut a pair in fabric plus one interfacing] 

The reason the waistband goes on before the zip insertion is because the zip runs right up into the waistband to finish at the top, there’s no overlap allowed with button or hooks and eyes. You could use the overlap method if you prefer but you’ll need to add some extra length to the waistband on one end to allow for the overlap. 

The lack of indication of the side seams on the waistband means you’ll need to pin carefully to evenly absorb any fullness of the trousers to ensure a good smooth fit to the waistband. [the side seam is probably at the halfway point but not necessarily, especially if you’ve made any fit adjustments to the waist] 

The instructions and illustrations for inserting the zip are pretty clear however there seems to be a contradiction with an earlier instruction which tells you to sew up the back crotch seam. Illustrations 13-15 appear to have the CB seam unsewn and 16 tells you to sew it up after inserting the zip but previous diagram 6 tells you to sew it up! No wonder I got in a muddle!! My suggestion would be, if you’re using an invisible zip as suggested, leave the CB seam unsewn AND ignore instruction 11 to sew up the inseam until after you’ve inserted the zip. Before sewing the waistband down I added to hanging tapes to each side seam so that I had an additional means to hang the trousers up if needs be.

Hopefully you’ve now arrived at a finished pair of trousers which simply need hemming. After checking the length wearing shoes (they come up pretty long) you could use the simple rolled hem finish as per the instructions or, as I did, leave a sizeable hem of about 5cms to give weight to the very flared leg width. I overlocked the edges to neaten and then used my blindhem stitch with the appropriate foot on the machine to finish [incidentally the photo is of a different project] I don’t use this technique often but it’s a good, and quick, finish on hems that don’t have too much, if any, curve. You could also slip hem by hand of course. 

Different project but still blind-hemming set up

The Palazzo pants are worth persevering with as they have a pleasing smooth fit over the waist and hips which is very comfortable and the leg is wide without being crazy-big. You could shorten them to culotte length very easily, they would work well in a variety of fabrics including linen, chambray or crepe, fabrics with a bit of drape and fluidity will look nicest as you don’t want to look like Coco the Clown!

I’m wearing them here with a top made from broderie anglaise that I found in a whole collection of fabric I was given by a friend. Her mother had been a wonderful dressmaker and I found the fabric pre-cut as this simple top which so I just sewed it up.
I’m wearing them here with one of my trusty Camber Set tops from Merchant & Mills

Overall I’m pleased with these trousers, they are a good fit and make a nice alternative to a skirt or close fitting trousers especially in warm weather.

If you encounter any problems with them that I might be able to help with do message me and I’ll try my best.

Until next time, happy sewing

Sue

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s